Broadcast-safe

Source: Wikipedia, the free encyclopedia.

Broadcast-safe video (broadcast legal or legal signal) is a term used in the

audio compliant with the technical or regulatory broadcast requirements of the target area or region the feed might be broadcasting to.[1] In the United States, the Federal Communications Commission (FCC) is the regulatory authority; in most of Europe, standards are set by the European Broadcasting Union
(EBU).

Broadcast safe video

Broadcast safe standard-definition video

Broadcast safe 625 video

Broadcast safe standards for 625 lines of

standard-definition (Inaccurately referred to as PAL, a colour encoding that is usually used with such systems) video are:[2][3]

  • Common name = 625/50i (576i)[4]
  • Commonly used digital
    SMPTE 259M-C
    , 270 Mbit/s bitrate
  • Commonly used No. of Vertical Lines = 625 (576 visible active video)
  • Commonly used Frame rate = 25 Hz (25 interlaced frame/s)
  • Commonly used TV Resolution = 720 x 576 (576i)
  • Black levels = 0 mV or 0 IRE
  • White levels (Chrominance amplitude):
    • 700 mV p-p or 100 IRE - 100% intensity setting which corresponds to 100.0.100.0 SMPTE color bars.
    • 75% intensity corresponding to 100.0.75.0 color bars, also referred to as EBU Bars.
Variants
Resolution Aspect ratio Pixel aspect ratio Form of scanning Framerate (Hz)
Vertical Horizontal
576 352 4:3 or 16:9 non-square interlaced 25 (50 fields/s)
progressive 25
480 4:3 or 16:9 non-square interlaced 25 (50 fields/s)
progressive 25
544 4:3 or 16:9 non-square interlaced 25 (50 fields/s)
progressive 25
720 4:3 or 16:9 non-square interlaced 25 (50 fields/s)
progressive 25
50

Broadcast safe 525 video

Broadcast safe standards for 525 lines of

standard-definition (System M, NTSC, NTSC-J, PAL-M) video are:[5][6][7][8][9]

  • Common name = 525/60i (480i)[4]
  • Commonly used digital
    SMPTE 259M-C
    , 270 Mbit/s bitrate
  • Commonly used Frame rate = 30 frame/s black and white, 29.97 interlaced frame/s color
  • Black level = 7.5 IRE for NTSC, 0 IRE for NTSC-J in Japan and PAL-M in Brazil.
  • Blanking level = 0 IRE
  • White levels = 100 IRE, 714 mV
  • Maximum signal level = 120 IRE
  • Minimum signal level = -20 IRE
Variants
Resolution Aspect ratio Pixel aspect ratio Form of scanning Framerate (Hz)
Vertical Horizontal
480 640 4:3 square interlaced 29.97 (59.94 fields/s)
30 (60 fields/s)
progressive 23.976
24
29.97
30
59.94
60
720 4:3 or 16:9 non-square interlaced 29.97 (59.94 fields/s)
30 (60 fields/s)
progressive 23.976
24
29.97
30
59.94
60

Broadcast safe High Definition video

Digital broadcasting is very different from analog. The NTSC and PAL standards describe both transmission of the signal and how the electrical signal is converted into an image. In digital, there is a separation between the subject of how data is to be transmitted from tower to TV, and the subject of what content that data might contain. While data transmission is likely to be a fixed and consistent affair, the content could vary from High Definition video, to SD multicasting the next, and even to non-video datacasting. For ATSC 1.0, 8VSB transmits the data, while MPEG-2 encodes pictures and sound.

Resolution Aspect ratio Pixel aspect ratio Form of scanning Frame rate (Hz)
Vertical Horizontal
720 1280 16:9 square progressive 23.976
24
25
29.97
30
50
59.94
60
1080 1920 16:9 square interlaced 25 (50 fields/s)
29.97 (59.94 fields/s)
30 (60 fields/s)
progressive 23.976
24
25
29.97
30
50
59.94
60

Broadcast safe audio

Broadcast engineers in North America usually line up their audio gear to nominal reference level of 0 dB on a VU meter aligned to +4dBu or -20dBFs, in Europe equating to roughly +4 dBm or -18 dBFS. Peak signal levels must not exceed the nominal level by more than +10 dB.[10]

Broadcast audio as a rule must be as free as possible of Gaussian noise, that is to say, it must be as far from the noise floor, as is reasonably possible considering the storage or transmission medium.

Broadcast audio must have a good

cockpit voice recorders
), sonic enhancement is recommended.

Non-standard video

Although almost any video gear can create problems when broadcast, equipment aimed at consumers sometimes produces video signals which are not broadcast safe. Usually this is to reduce the cost of the gear, since a non-standard video signal in the home might not create the problems that one might find in a broadcast facility. Potential flaws exist with:

In digital television only environments

In nations that have fully converted to digital television, broadcast safe analogue television takes on a slightly different meaning. All broadcasting systems will have been mostly converted to digital only outputs, leaving fewer entry points for analogue television signals.

What this means is that all devices that feed to the television transmitter must take in and feed standard analogue television signals into the transmission chain. Mostly it is up to the switcher to notify if there is non-broadcast safe video to the programmer. However, due to the limitations of many switchers for DTV and HDTV it ultimately is up to the automation systems to alert the programmer of non-broadcast safe video inputs.

As a matter of broadcast engineering practice, 4:3 analogue television signals will always pose the most problems with broadcast safe compliance. The use of portable and cheap timebase-genlock systems for analogue television inputs in the digital television studio will be clearly mandatory for the next 50 years.[original research?]

See also

References

  1. ^ "Learn". Archived from the original on 1 October 2011. Retrieved 22 March 2015.
  2. ^ Matrox - Composite video measurements Archived January 7, 2008, at the Wayback Machine
  3. ^ "VideoUniversity.com - PAL Colour Bars". Archived from the original on 8 February 2012. Retrieved 22 March 2015.
  4. ^ a b "Digital Video Encoding (DV, DVCAM, DVCPRO)". February 2012. Retrieved 22 March 2015.
  5. ^ "VideoUniversity.com - Engineering Primer". Archived from the original on 3 March 2016. Retrieved 22 March 2015.
  6. ^ Tektronix - The Color Bars Signal -- Why and How
  7. ^ "7.5 IRE Setup". Retrieved 22 March 2015.
  8. ^ "Final Cut Pro, Avid Media Composer, and Premiere Training". Retrieved 22 March 2015.
  9. ^ "VideoUniversity.com - Broadcast Requirements for Commercials and Informercials". Archived from the original on 4 March 2016. Retrieved 22 March 2015.
  10. ^ "Shure Tech Tip: VU and PPM Audio Meters – An Elementary Explanation". Retrieved 22 March 2015.