General Packet Radio Service

Source: Wikipedia, the free encyclopedia.
(Redirected from
GPRS
)

Part of a series on the
Wireless network technologies
Analog
Digital
Mobile telecommunications
Sony Ericsson K310a showing Wikipedia homepage via internet GPRS.

General Packet Radio Service (GPRS), also called 2.5G, is a

3rd Generation Partnership Project (3GPP).[2][3]

GPRS is typically sold according to the total volume of data transferred during the billing cycle, in contrast with circuit switched data, which is usually billed per minute of connection time, or sometimes by one-third minute increments. Usage above the GPRS bundled data cap may be charged per MB of data, speed limited, or disallowed.

GPRS is a

2.5G, that is, a technology between the second (2G) and third (3G) generations of mobile telephony.[5] It provides moderate-speed data transfer, by using unused time-division multiple access (TDMA) channels in, for example, the GSM system. GPRS is integrated into GSM Release 97 and newer releases. Mobile devices with GPRS started to roll out around the year 2001.[6]

Technical overview

See also:
GPRS Core Network

The GPRS core network allows

WCDMA mobile networks to transmit IP packets to external networks such as the Internet. The GPRS system is an integrated part of the GSM network switching subsystem.[7][8][9]

Services offered

GPRS extends the GSM Packet circuit switched data capabilities and makes the following services possible:

  • SMS messaging and broadcasting
  • "Always on" internet access
  • Multimedia messaging service (MMS)
  • Push-to-talk over cellular (PoC)
  • Instant messaging and presence—wireless village
  • Internet applications for smart devices through wireless application protocol (WAP)
  • Point-to-point (P2P) service: inter-networking with the Internet (IP)
  • Point-to-multipoint (P2M) service: point-to-multipoint multicast and point-to-multipoint group calls

If SMS over GPRS is used, an SMS transmission speed of about 30 SMS messages per minute may be achieved. This is much faster than using the ordinary SMS over GSM, whose SMS transmission speed is about 6 to 10 SMS messages per minute.

Frequencies

As the GPRS standard is an extension of GSM capabilities, the service operates on the

cellular communication GSM frequencies.[8][10] GPRS devices can typically use (one or more) of the frequencies within one of the frequency bands the radio supports (850, 900, 1800, 1900 MHz). Depending on the device, location and intended use, regulations may be imposed either restricting or explicitly specifying authorised frequency bands.[10][11][12]

GSM-850 and GSM-1900 are used in the United States, Canada, and many other countries in the Americas. GSM-900 and GSM-1800 are used in: Europe, Middle East, Africa and most of Asia. In South Americas these bands are used in Costa Rica (GSM-1800), Brazil (GSM-850, 900 and 1800), Guatemala (GSM-850, GSM-900 and 1900), El Salvador (GSM-850, GSM-900 and 1900). There is a more comprehensive record of international cellular service frequency assignments

Protocols supported

GPRS supports the following protocols:

  • IPv4 before IPv6
    is widespread.
  • Point-to-Point Protocol (PPP) is typically not supported by mobile phone operators but if a cellular phone is used as a modem for a connected computer, PPP may be used to tunnel IP to the phone. This allows an IP address to be dynamically assigned (using IPCP rather than DHCP) to the mobile equipment.
  • X.25 connections are typically used for applications like wireless payment terminals, although it has been removed from the standard. X.25 can still be supported over PPP, or even over IP, but this requires either a network-based router to perform encapsulation or software built into the end-device/terminal; e.g., user equipment (UE).

When TCP/IP is used, each phone can have one or more IP addresses allocated. GPRS will store and forward the IP packets to the phone even during handover. The TCP restores any packets lost (e.g. due to a radio noise induced pause).

Hardware

Devices supporting GPRS are grouped into three classes:

Class A
Can be connected to GPRS service and GSM service (voice, SMS) simultaneously. Such devices are now available[as of?].
Class B
Can be connected to GPRS service and GSM service (voice, SMS), but using only one at a time. During GSM service (voice call or SMS), GPRS service is suspended and resumed automatically after the GSM service (voice call or SMS) has concluded. Most GPRS mobile devices are Class B.
Class C
Are connected to either GPRS service or GSM service (voice, SMS) and must be switched manually between one service and the other.

Because a Class A device must service GPRS and GSM networks together, it effectively needs two radios. To avoid this hardware requirement, a GPRS mobile device may implement the dual transfer mode (DTM) feature. A DTM-capable mobile can handle both GSM packets and GPRS packets with network coordination to ensure both types are not transmitted at the same time. Such devices are considered pseudo-Class A, sometimes referred to as "simple class A". Some networks have supported DTM since 2007[citation needed].

Huawei E220 3G/GPRS Modem

USB 3G/GPRS modems have a

pendrive
.

Addressing

A GPRS connection is established by reference to its access point name (APN). The APN defines the services such as wireless application protocol (WAP) access,

short message service (SMS), multimedia messaging service (MMS), and for Internet communication services such as email and World Wide Web
access.

In order to set up a GPRS connection for a wireless modem, a user must specify an APN, optionally a user name and password, and very rarely an IP address, provided by the network operator.

GPRS modems and modules

GSM module or GPRS modules are similar to modems, but there's one difference: the modem is an external piece of equipment, whereas the GSM module or GPRS module can be integrated within an electrical or electronic equipment. It is an embedded piece of hardware. A GSM mobile, on the other hand, is a complete embedded system in itself. It comes with embedded processors dedicated to provide a functional interface between the user and the mobile network.

Coding schemes and speeds

The upload and download speeds that can be achieved in GPRS depend on a number of factors such as:

  • the number of
    BTS
    TDMA time slots assigned by the operator
  • the channel encoding used.
  • the maximum capability of the mobile device expressed as a
    GPRS multislot class

Multiple access schemes

The

dynamic TDMA
with first-come first-served.

Channel encoding

The channel encoding process in GPRS consists of two steps: first, a cyclic code is used to add parity bits, which are also referred to as the Block Check Sequence, followed by coding with a possibly punctured convolutional code.[13] The Coding Schemes CS-1 to CS-4 specify the number of parity bits generated by the cyclic code and the puncturing rate of the convolutional code.[13] In Coding Schemes CS-1 through CS-3, the convolutional code is of rate 1/2, i.e. each input bit is converted into two coded bits.[13] In Coding Schemes CS-2 and CS-3, the output of the convolutional code is punctured to achieve the desired code rate.[13] In Coding Scheme CS-4, no convolutional coding is applied.[13] The following table summarises the options.

GPRS
Coding scheme 		Bitrate including RLC/MAC overhead[a][b]
(kbit/s/slot) 		Bitrate excluding RLC/MAC overhead[c]
(kbit/s/slot) 		Modulation Code rate
CS-1 9.20 8.00 GMSK 1/2
CS-2 13.55 12.00 GMSK ≈2/3
CS-3 15.75 14.40 GMSK ≈3/4
CS-4 21.55 20.00 GMSK 1
  1. ^ This is rate at which the RLC/MAC layer protocol data unit (PDU) (called a radio block) is transmitted. As shown in TS 44.060 section 10.0a.1,[14] a radio block consists of MAC header, RLC header, RLC data unit and spare bits. The RLC data unit represents the payload, the rest is overhead. The radio block is coded by the convolutional code specified for a particular Coding Scheme, which yields the same PHY layer data rate for all Coding Schemes.
  2. ^ Cited in various sources, e.g. in TS 45.001 table 1.[13] is the bitrate including the RLC/MAC headers, but excluding the uplink state flag (USF), which is part of the MAC header,[15] yielding a bitrate that is 0.15 kbit/s lower.
  3. ^ The net bitrate here is the rate at which the RLC/MAC layer payload (the RLC data unit) is transmitted. As such, this bit rate excludes the header overhead from the RLC/MAC layers.

The least robust, but fastest, coding scheme (CS-4) is available near a

base transceiver station
(BTS), while the most robust coding scheme (CS-1) is used when the mobile station (MS) is further away from a BTS.

Using the CS-4 it is possible to achieve a user speed of 20.0 kbit/s per time slot. However, using this scheme the cell coverage is 25% of normal. CS-1 can achieve a user speed of only 8.0 kbit/s per time slot, but has 98% of normal coverage. Newer network equipment can adapt the transfer speed automatically depending on the mobile location.

In addition to GPRS, there are two other GSM technologies which deliver data services:

video calling
may prefer HSCSD, especially when there is a continuous flow of data between the endpoints.

The following table summarises some possible configurations of GPRS and circuit switched data services.

Technology Download (kbit/s) Upload (kbit/s) TDMA timeslots allocated (DL+UL)
CSD 9.6 9.6 1+1
HSCSD 28.8 14.4 2+1
HSCSD 43.2 14.4 3+1
GPRS 85.6 21.4 (Class 8 & 10 and CS-4) 4+1
GPRS 64.2 42.8 (Class 10 and CS-4) 3+2
EGPRS
(EDGE) 		236.8 59.2 (Class 8, 10 and MCS-9) 4+1
EGPRS
(EDGE) 		177.6 118.4 (Class 10 and MCS-9) 3+2

Multislot Class

The multislot class determines the speed of data transfer available in the

Downlink
directions. It is a value between 1 and 45 which the network uses to allocate radio channels in the uplink and downlink direction. Multislot class with values greater than 31 are referred to as high multislot classes.

A multislot allocation is represented as, for example, 5+2. The first number is the number of downlink timeslots and the second is the number of uplink timeslots allocated for use by the mobile station. A commonly used value is class 10 for many GPRS/EGPRS mobiles which uses a maximum of 4 timeslots in downlink direction and 2 timeslots in uplink direction. However simultaneously a maximum number of 5 simultaneous timeslots can be used in both uplink and downlink. The network will automatically configure for either 3+2 or 4+1 operation depending on the nature of data transfer.

Some high end mobiles, usually also supporting

modulation and coding scheme can be used, 5 timeslots can carry a bandwidth of 5*59.2 kbit/s = 296 kbit/s. In uplink direction, 3 timeslots can carry a bandwidth of 3*59.2 kbit/s = 177.6 kbit/s.[17]

Multislot Classes for GPRS/EGPRS

Multislot Class Downlink TS Uplink TS Active TS
1 1 1 2
2 2 1 3
3 2 2 3
4 3 1 4
5 2 2 4
6 3 2 4
7 3 3 4
8 4 1 5
9 3 2 5
10 4 2 5
11 4 3 5
12 4 4 5
30 5 1 6
31 5 2 6
32 5 3 6
33 5 4 6
34 5 5 6

Attributes of a multislot class

Each multislot class identifies the following:

  • the maximum number of Timeslots that can be allocated on uplink
  • the maximum number of Timeslots that can be allocated on downlink
  • the total number of timeslots which can be allocated by the network to the mobile
  • the time needed for the MS to perform adjacent cell signal level measurement and get ready to transmit
  • the time needed for the MS to get ready to transmit
  • the time needed for the MS to perform adjacent cell signal level measurement and get ready to receive
  • the time needed for the MS to get ready to receive.

The different multislot class specification is detailed in the Annex B of the 3GPP Technical Specification 45.002 (Multiplexing and multiple access on the radio path)

Usability

The maximum speed of a GPRS connection offered in 2003 was similar to a modem connection in an analog wire telephone network, about 32–40 kbit/s, depending on the phone used. Latency is very high; round-trip time (RTT) is typically about 600–700 ms and often reaches 1s. GPRS is typically prioritized lower than speech, and thus the quality of connection varies greatly.

Devices with latency/RTT improvements (via, for example, the extended UL TBF mode feature) are generally available. Also, network upgrades of features are available with certain operators. With these enhancements the active round-trip time can be reduced, resulting in significant increase in application-level throughput speeds.

History

GPRS opened in 2000[18] as a packet-switched data service embedded in the channel-switched cellular radio network GSM. GPRS extends the reach of the fixed Internet by connecting mobile terminals worldwide.

The CELLPAC

UMTS) and LTE
rely on key GPRS functions for mobile Internet access as introduced by CELLPAC.

According to a study on history of GPRS development,[22] Bernhard Walke and his student Peter Decker are the inventors of GPRS — the first system providing worldwide mobile Internet access.

Enhanced GPRS

This section is an excerpt from Enhanced Data rates for GSM Evolution.[edit]
EDGE sign shown in notification bar on an Android-based smartphone.

Cingular (now AT&T) in the United States.[24]

EDGE is standardized also by 3GPP as part of the GSM family. A variant, so called Compact-EDGE, was developed for use in a portion of Digital AMPS network spectrum.[25]

Through the introduction of sophisticated methods of coding and transmitting data, EDGE delivers higher bit-rates per radio channel, resulting in a threefold increase in capacity and performance compared with an ordinary GSM/GPRS connection.

EDGE can be used for any packet switched application, such as an Internet connection.

Evolved EDGE continues in release 7 of the 3GPP standard providing reduced latency and more than doubled performance e.g. to complement High-Speed Packet Access (HSPA). Peak bit-rates of up to 1 Mbit/s and typical bit-rates of 400 kbit/s can be expected.

See also

References

  1. ^ "Is General Packet Radio Service (GPRS) 2G, 3G or 4G? – Commsbrief". Retrieved 2023-07-16.
  2. ^ "Welcome to the World of Standards!". ETSI.
  3. ^ "3GPP – The Mobile Broadband Standard". 3GPP.
  4. ^ "General packet radio service from Qkport". Archived from the original on 2010-01-28. Retrieved 2009-12-14.
  5. ^ "Mobile Phone Generations from". Archived from the original on 2010-06-11.
  6. ^ "Q&A: GPRS phones". 2001-05-18. Retrieved 2023-07-16.
  7. ^ "What Is GPRS (General Packet Radio Service)? Meaning, Working, Advantages, and Applications". Spiceworks. Retrieved 2023-05-01.
  8. ^ a b Sandeep Bhandari (2021-09-17). "Difference Between GSM and GPRS". askanydifference.com. Retrieved 2023-05-01.
  9. ^ "4G vs GPRS: What is the difference between 4G LTE and GPRS?". Commsbrief. Retrieved 2023-05-01.
  10. ^ a b "Ofcom UK Frequency Allocation (UKFAT) Page". static.ofcom.org.uk. Retrieved 2023-05-01.
  11. ^ "What frequency does the data traffic use in GPRS?". Honeywell AIDC. Honeywell. 2014-10-07. Archived from the original on 2023-05-01. Retrieved 2023-05-01.
  12. ^ "Mobile Spectrum Assignments by Country". CellMapper Wiki. Retrieved 2023-05-01.
  13. ^ a b c d e f 3rd Generation Partnership Project (November 2014). "3GGP TS45.001: Technical Specification Group GSM/EDGE Radio Access Network; Physical layer on the radio path; General description". 12.1.0. Retrieved 2015-12-05.{{cite web}}: CS1 maint: numeric names: authors list (link)
  14. ^ 3rd Generation Partnership Project (June 2015). "3GGP TS45.001: Technical Specification Group GSM/EDGE Radio Access Network; Mobile Station (MS) - Base Station System (BSS) interface; Radio Link Control / Medium Access Control (RLC/MAC) protocol; section 10.0a.1 - GPRS RLC/MAC block for data transfer". 12.5.0. Retrieved 2015-12-05.{{cite web}}: CS1 maint: numeric names: authors list (link)
  15. ^ 3rd Generation Partnership Project (June 2015). "3GGP TS45.001: Technical Specification Group GSM/EDGE Radio Access Network; Mobile Station (MS) - Base Station System (BSS) interface; Radio Link Control / Medium Access Control (RLC/MAC) protocol; section 10.2.1 - Downlink RLC data block". 12.5.0. Retrieved 2015-12-05.{{cite web}}: CS1 maint: numeric names: authors list (link)
  16. ^ 3rd Generation Partnership Project (March 2015). "3GGP TS45.002: Technical Specification Group GSM/EDGE Radio Access Network; Multiplexing and multiple access on the radio path (Release 12)". 12.4.0. Retrieved 2015-12-05.{{cite web}}: CS1 maint: numeric names: authors list (link)
  17. ^ "GPRS and EDGE Multislot Classes". Archived from the original on 2010-11-27. Retrieved 2010-06-21.
  18. ISBN 9781591400158
    .
  19. ISSN 1090-3038. Archived
    (PDF) from the original on 2021-11-17. Retrieved 2021-11-27. (6 pages)
  20. Walke, Bernhard H. (1993-10-13). A General Packet Radio Service proposed for GSM (PDF). ETSI SMG Workshop "GSM in a Future Competitive Environment". Helsinki, Finland. pp. 1–20. Archived
    (PDF) from the original on 2021-09-18. Retrieved 2021-11-15. (11 pages)
  21. ^ Program “Publish or Perish”, see [1] returns to a search for P. Decker, B. Walke, their most cited paper that unveils US patents referencing that paper.
  22. ComNets Research Group: 12–23. Archived
    (PDF) from the original on 2021-09-18. Retrieved 2021-11-15. (19 pages)
  23. ^ "Archived copy" (PDF). Archived from the original (PDF) on 2009-03-06. Retrieved 2011-05-10.{{cite web}}: CS1 maint: archived copy as title (link)
  24. ^ http://www.itu.int/ITU-D/imt-2000/MiscDocuments/IMT-Deployments-Rev3.pdf. Retrieved 2008-04-16. {{cite web}}: Missing or empty |title= (help)[dead link]
  25. ^ ETSI SMG2 99/872

External links

Retrieved from "https://en.wikipedia.org/w/index.php?title=General_Packet_Radio_Service&oldid=1219048996"
This page is based on the copyrighted Wikipedia article: GPRS. Articles is available under the CC BY-SA 3.0 license; additional terms may apply.Privacy Policy