Hybrid Illinois Device for Research and Applications

Edit links
Source: Wikipedia, the free encyclopedia.

HIDRA
Hybrid Illinois Device for Research and Applications
kW
 (2.45 GHz magnetron, ohmic heating)
History
Year(s) of operation
HIDRA being assembled as of December 2014. (Photo: Daniel Andruczyk)

The Hybrid Illinois Device for Research and Applications (HIDRA) is a medium-sized toroidal magnetic fusion device housed in the

University of Illinois at Urbana–Champaign, United States. HIDRA had its first plasma at the end of April 2016 and started experimental campaigns by December of that year. HIDRA is the former WEGA classical stellarator that was operated at the Max Planck Institute for Plasma Physics in Greifswald
Germany from 2001 to 2013.

A unique aspect of HIDRA is that it can operate as a

NSTX, LTX, EAST, T-11M, RFX, FTU and TJ-II
.

History

Some argue that HIDRA is the most well traveled fusion devices in the world. From its beginnings in France it has operated in 3 countries and 4 cities. The research goals of the device have dramatically changed over the years from doing wave heating studies to being a testbed for one of the world's most sophisticated fusion devices and now to studying the way plasmas interact with the inside wall and materials of fusion devices. In fact, it will be the first toroidal fusion-relevant device that will be solely dedicated to the study of plasma wall (PWI), plasma surface (PSI) and plasma material interactions (PMI).

Centre d’Etudes Nucléaires (1972–1982)

HIDRA, started off as a different machine at the Centre d’Etudes Nucléaires in Grenoble, France in 1972. Back then it was called WEGA with construction of the device from 1972 to 1975. WEGA was a joint project between CEA Grenoble and the Max Planck Institute for Plasma Physics in Germany to study RF heating and lower hybrid heating. There were three vacuum vessel that were built, two tokamak and a single stellarator. WEGA primarily operated as a tokamak from 1975 to 1987[1] despite plans to install the stellarator vessel in 1976 (repairs were needed on the helical coil insulation). Electron and ion temperatures achieved were, Te = 600 – 900 eV and, Ti = 150 – 250 eV. Densities of ne = 1.6×1019 m−3 with a plasma current of IP = 45 – 60 kA and heating power, Pohm = 100 – 130 kW and, PRF = 100 kW. Typical pulse duration was, Δt = 5 – 15 ms and an energy confinement time, τE = 3 – 5 ms.[2]

WEGA was then converted over to a "classical Stellarator" design with the toroidal coils kept in place and a new vacuum vessel with four helical coils winding around the vessel.[3][4] It was operated as a Stellarator until 1982 when it moved to the University of Stuttgart, in the then West Germany.

Institut für Plasmaforschung (1982–2000)

The WEGA stellarator being assembled at IPF Stuttgart. (Photo: Courtesy of IPP Greifswald)

In 1982 WEGA moved from Grenoble to the University of Stuttgart in Germany. Unfortunately in Stuttgart it seems that WEGA was not used much. There is not a lot of information from this time and it is very difficult to see what results came out of this 18-year time period. The issues seem to be a lack of enough heating power and cooling. However, IPF did have the stellarator vacuum vessel installed and some of the first magnetic flux surface measurements were performed.[5]

Max-Planck-Institut für Plasmaphysik (2001–2013)

From 2000 to 2001 WEGA moved from Stuttgart to Greifswald. At this stage a new institute had been built in the former East German city to stimulate economic, scientific and educational growth in the region. MPIPP Greifswald was designated to house the brand new modular stellarator W7-X. While W7-X was being built WEGA was brought in to be the machine where much of the diagnostic, heating and control work for W7-X would be tested and perfected.[6][7][8] It also provided a valuable tool in the training and teaching of future generations of fusion and plasma scientists and engineers. In fact, though the name was the same the acronym for WEGA changed to "Wendelstein Experiment in Greifswald für Ausbildung" the Wendelstein experiment in Greifswald for Training.[9]

WEGA's magnetic coil systems were run via transformer and rectifier sets that allowed steady state operations. This made WEGA unique among the smaller toroidal fusion devices that normally are pulsed, and only the larger devices such as LHD and W7-X have that kind of steady state capability. Some of the achievements on WEGA include the development of an OXB heating scheme that allows ECRH heating above the cut off density for the electrons in the plasma.[10][11] This allowed densities almost 100 times higher to be achieved, where temperatures were on average around Te = 15 eV and densities around ne ~ 1018 m−3.[12][13][14] Ion temperatures around Ti = 1-2 eV.[15] The W7-X control system was tested on WEGA showing the real time capability of measuring plasma parameters and control of the machine. It was demonstrated, that despite being a stellarator, a plasma current could be driven via microwave heating of the plasma.[16][17]

Furthermore, a heavy ion beam probe (HIBP) was also developed for the measurement of radial profiles of the electric plasma potential.

University of Illinois at Urbana-Champaign
, and details for the transfer were completed in the summer of 2014.

Center for Plasma Material-Interactions
(2014–present)

HIDRA being assembled at the University of Illinois Urbana–Champaign. (Photo: Daniel Andruczyk)

With W7-X operations starting in 2014, the space occupied by WEGA and its power systems was taking up much needed real-estate for the Thomson Scattering system and a cryogenic pellet injection system. During the 2013 SOFE conference, Daniel Andruczyk, a former Post-Doc on WEGA, met with some former colleagues and it was suggested that the University of Illinois could potentially take WEGA to the USA. After a year of negotiating between the director of the Center for Plasma Material Interactions, David Ruzic, the university and IPP, the funds were secured to make it happen. Andruczyk was brought on to lead the project of dismantling and shipping WEGA to the Urbana-Champaign Campus in Illinois. Upon arrival the Machine was renamed the Hybrid Illinois Device for Research and Applications. The Hybrid part being that it still has the tokamak capabilities, not only the stellarator ones.

It took nearly 8 weeks over the autumn of 2014 of dismantling the device in Germany and was packed and shipped to the US in October. By early 4 November shipping containers worth of fusion device arrived by flat bed-truck to the University of Illinois at the Center for Plasma Material Interactions.[21] Aside from lab personnel, the universities facilities and services division were heavily involved in helping to off load, move in and assemble much of the larger, heavier components. Construction began in earnest with the transformers and rectifiers for the helical and toroidal magnetic coils moving in first. Once these were established then the base was brought in and the yokes, center-stack, half-tori and vertical field coils all installed over the next ten days.[22]

HIDRA foremost is an educational tool for training future fusion scientists and engineers. Everything with the machine is done such that students can use it. The control system was written by senior undergrad and grad students and allows the machine to be controlled from one computer via a LabView program. This also sends out the trigger signals that are needed to fire the various data acquisition and diagnostic systems. HIDRA essentially can be controlled and run by a single person.[23]

Current Status and Research

HIDRA currently is routinely operating at least 1–2 days a week. Typical plasma shots have durations running from 40 - 1000 s long using a mixture of gases, helium, hydrogen, deuterium and mixtures of hydrogen/helium. Argon and Neon are also possible along with the occasional nitrogen discharge. The current director of HIDRA is Associate Research Professor Dr. Daniel Andruczyk with 2 other professors affiliated with HIDRA. There are 3 graduate students and 4 undergraduate students doing research with HIDRA. A material analysis tool (HIDRA-MAT) has also been installed and commissioned to do plasma material interaction studies. An extensive collaboration has developed around the device with members from around the US and the world contributing to the device.

First Plasma (2016)

In April 2016, HIDRA had its first plasma, a simple glow plasma discharge, during the Nuclear, Plasma and Radiological Engineering Departments Open house. With nearly 100 dignitaries and guests including the head of the NPRE department and Dean of the Grainger College of Engineering, the HIDRA team was able to demonstrate that all the working components of the device were installed and running and that operations were able to begin. A short 120 s plasma discharge was initiated around 4 pm demonstrating the machines operational capabilities. HIDRA was shutdown for 3 months after that for further device installation and commissioning. Once the upgrades and installations were complete the first set of characterization experiments verifying the performance of the magnets and HIDRA operations.[24]

Flux Surface Measurements (2017 - 2018)

iota = 1/3 magnetic flux surfaces showing the islands. (Photo: Daniel Andruczyk)

The first set of data was the characterization of the magnetic

electron beams themselves.[25]

There are two DC magnetic probes used to monitor the magnetic field. There is a static probe that is situated at the edge of the vessel. This is used to monitor the magnetic field during the plasma discharge. There is a second DC magnetic probe mounted on a reciprocating probe in vacuum that allows radial scans of the magnetic field (without plasma). The probe itself is rotatable which allow horizontal, vertical and helical magnetic fields to be measured. This probe is mainly used in the Fall Semester of the university year during a plasma laboratory class to understand how magnetic fields affect plasmas.

An interesting effect of the HIDRA magnetic field operation is that the helical field can be ramped down while the

electron beam
, can visualize the drift of electrons.

Magnetron Plasmas (2018 - Present)

First plasma in HIDRA. This is with helium as the gas. (Photo: Daniel Andruczyk)

With most of 2017 and parts of 2018 being taken up with flux surface measurements and figuring out machine operation, the first magnetron plasmas were initiated at the end of 2018. A 2.45 GHz magnetron system is used to do generate electron cyclotron resonantly heated plasmas. Currently only the 6 kW system is operation, however this is enough to generate plasmas with electron temperatures on the order of TE = 10 – 20 eV and plasma densities up to ne = 13×1018 m−3. Ion temperatures have been measured using doppler broadening of the helium ion line and are typically around 10% of the electron temperature. There is a 20 kW magnetron system that will be available in future once commissioned.

From 2016 to 2019, HIDRA and CPMI was part of international collaboration to develop liquid lithium systems for long pulsed plasma operation. Confirming the magnetic flux surfaces and also magnetron operation was part of developing liquid metal technologies and was done in together with several labs around the US and China.[26]

The system is designed for steady state operation. The shortest duration plasma pulses currently are t = 40 s with flat top durations of tflat = 20 s. A typical experimental run has 5 seconds of no magnetic field with a 5 s ramp up to the desired field strengths. At the end of a pulse there is a 5 s ramp down and a further 5 s of no field. The longest duration plasma discharges currently run at 1000 s. These now are run quite routinely in HIDRA and are integral to the PMI experiments being performed. A typical plasma power run on HIDRA is anywhere from 1.2 kW < Pheat < 5.4 kW.

A fast reciprocating arm with a Langmuir probe is used to measure radial profiles of the electron temperature, Te, electron density, ne, floating potential Vf and plasma potential VP. Taking a measurement and saving the data takes approximately 52s. In a 1000 s discharge roughly 18 radial profile measurements can be taken to get a spatial and temporal profile of the plasma. This is to compliment and benchmark the spectroscopic collisional radiative model (CRM) technique used to also measure density and temperature.

HIDRA Material Analysis Teststand (HIDRA-MAT) (2019 - present)

The HIDRA Material Analysis Teststand (HIDRA-MAT) installed on HIDRA. This allows some surface characterization in-vacuo. The LIBS laser can be seen as well as the transfer arm.

In 2019 the HIDRA Material Analysis Teststand (HIDRA-MAT) was commissioned and the first exposures of tungsten samples were performed.[27] HIDRA-MAT was designed to be able to do surface characterization without having to break vacuum, that is in-vacuo measurements. This ability allows study of the temporal evolution of the surface as well. HIDRA-MAT was based on the Material Analysis Particle Probe (MAPP) that has been successfully used on LTX and NSTX. The system head allows material samples to be mounted securely and exposed to the HIDRA plasma. The probe head can be heated to 1000 oC and is attached to a translational stage that has a stroke of 800 mm. The Probe head also can be rotated from +90o to -90o. when in the +90o position a liquid lithium injector can place a controlled droplet of liquid lithium onto the material surface.[28] The probe then can be rotated back to 0o and inserted into the plasma. Furthermore, when in the -45o position, this allows the surface to be exposed to the LIBS/LIDS laser.

Retention studies of the surface with the plasma fuel gas can be performed. For example, is funning a D2 + He plasma, and a tungsten surface, the sample can be heated to do thermal desorption spectroscopy (TDS) measurements. To distinguish between the two gases (mass 4 for both) a dual RGA system has been developed that allows one gas to be subtracted from the other.[29]

Plasma Material Interaction (PMI) and Lithium Operations (2020 - present)

HIDRA plasma with lithium operation - PMI observed
HIDRA operations with lithium. This is shot# 3381 in the March 2021 campaign. (Photo: Daniel Andruczyk)

The first plasma operations with liquid lithium were performed in March 2021. This was done via a tungsten substrate mounted on HIDRA-MAT and a drop of lithium, mLi = 100 mg, places on it surface. This was inserted into a 600 s, 5.4 kW plasma and exposed at the scrape off layer edge in a = 1/4 plasma, near an island. Initial PMI was observed and eventually all the lithium was evaporated off the surface. However once the lithium interacted with the plasma and was ionized, the background helium gas which was being recycled off the wall disappeared despite a constant flow of helium into the HIDRA vacuum chamber. The effect was that the plasma temperature went from Te = 18 eV to over Te = 50 eV. The temperature on the surface of HIDRA-MAT spiked to over 2000 oC, and the molybdenum clips were melted. a corner of the ECRH antenna which was exposed to the plasma also melted die to the increased PMI.[30]

The mechanism for how the helium is being pumped out by the lithium is yet unknown. Thus, in November 2021 a new lithium campaign was undertaken to try and get a better understanding of what is going on. Future studies in 2022 will also be performed with

hydrogenic
species and helium pumping with liquid lithium. HIDRA along with HIDRA-MAT has the capabilities to explore this.

Plasma material interactions (PMI) play a pivotal role in fusion reactor operation and it's critical to have a dedicated toroidal machine to study these phenomena. It is anticipated that HIDRA will be able to reach the necessary conditions to study tungsten fuzz (W-fuzz). Already, under some conditions, precursors to fuzz formation have been observed. The long pulse aspect of HIDRA means that the required

Plasma chemistry
is another critical aspect that needs to be studied. This not only can lead to molecules that are detrimental to fusion operation, but also dust formation, re-deposition of material around the machine and "UFO's" formation. In fusion studies UFO's do refer to "unidentified flying objects" which are seen as sparks and bright spots that can form and travel around the vacuum vessel. These sometimes will be trapped on the field lines and sometimes are not. Their origin usually is not seen and just by viewing them on camera cannot determine what they are. Hence the "UFO" designation. During the lithium experiments on HIDRA in 2021, such UFO's were observed.

Summary of HIDRA Operations and Diagnostics - Current and Future

Operating Conditions

Summary of HIDRA under standard operating conditions.
Parameter Unit Value
Major Radius m R0 0.72
Vessel Minor Radius m r 0.19
Plasma Minor Radius m a 0.10 - 0.15
HIDRA Volume m3 V 0.51
HIDRA Surface m2 S 5.4
On-axis Magnetic Fields T (gauss) B0 <0.5 (5000)
Plasma Heating kW P 6 + 20
Electron Temperature eV Te < 25
Ion Temperature eV Ti < 2
Plasma Density m−3 ne < 5×1018
Base Pressure Pa (torr) p0 6.6×10−5 (5×10−7)
Operating Pressure Pa (torr) p 1.3×10−3 (1×10−5)

Operational Capabilities

Operational Capabilities of HIDRA.
Parameter Unit Value
Electron Temperature Standard eV Te < 25
Lithium eV Te < 60
Ion Temperature Standard eV Ti < 2
Lithium eV Ti < 5
Plasma Density Standard m−3 ne < 5×1018
Lithium m−3 ne < 1×1019
Plasma Volume m3 Vplasma 0.14 - 0.32
Particle Flux m−2s−1 Ω <1×1022
Discharge Duration s tplasma 40- 1000
Operating Gases H2, D2 He H2+He, D+He Ar, Ne

In Vessel Diagnostics

HIDRA plasma and in vessel diagnostics.
Diagnostic Measurement Status
Edge Langmuir Probe Particle Confinement time OPERATIONAL
Fast Reciprocating Probe Te, ne, Vf, VP OPERATIONAL
Survey Spectrometer #1 (200 - 110 nm) Te, ne, impurities, Hα, He, Li, Li+ OPERATIONAL
Survey Spectrometer #2 (300 - 800 nm) When needed
Recycling Spectrometer (630 - 680 nm) Hα, He, Li OPERATIONAL
Doppler Spectrometer (450 - 490 nm) Ti, Hβ, He As needed
Camera #1 FRP, ECRH, ELP OPERATIONAL
Camera #2 In Vessel OPERATIONAL
Camera #3 HIDRA-MAT OPERTATIONAL
Camera #4 - Open
RGA #1 Plasma Chemistry OPERATIONAL
RGA #2 OPERATIONAL
RGA #3 OPERATIONAL
FR Pressure Gauge North HIDRA Main Vessel OPERATIONAL
FR Pressure Gauge South HIDRA Main Vessel OPERATIONAL
FR Pressure Gauge Pump 1 Turbo Pump 1 OPERATIONAL
FR Pressure Gauge Pump 2 Turbo Pump 2 OPERATIONAL
FR Pressure Gauge FRP FRP OPERATIONAL
FR Pressure Gauge HIDRA-MAT HIDRA-MAT - OPERATIONAL
Mirnov Coil Turbulence, Plasma Shape In Development
Diamagnetic Loop Stored Energy, Te In Development
Inner Plate Heat Flux In Development
IR Camera In Development
DC Hall Probe B0 OPERATIONAL
Reciprocating DC Hall Probe Bin, B0, Bout OPERATIONAL
6 kW magnetron ECRH OPERATIONAL
20 kW magnetron ECRH Not Operational
Microwave Sniffer Probe Power Absorption OPERATIONAL
2 kW RF ICRH To be Developed
SHeB (He diagnostic beam) Te, ne Future
Squirt Fueling beam Future

HIDRA-MAT Capabilities

Capabilities of HIDRA-MAT
Diagnostic Parameter Status
Probe Head Exposure, LIBS OPERATIONAL
Probe Head Heater Exposure, TDS, LIDS OPERATIONAL
Lithium Injector Exposure OPERATIONAL
Thermocouple 1 Probe Surface OPERATIONAL
Thermocouple 2 Probe Surface OPERATIONAL
Thermocouple 3 Probe Heater OPERATIONAL
IR Camera Surface Temperature OPERATIONAL
Laser LIBS, LIDS OPERATIONAL
200-1100 nm Spectrometer LIBS OPERTATIONAL
RGA 1 Main HIDRA-MAT Main Vessel OPERATIONAL
RGA 2 Sniffer (25 V) TDS, LIDS (D2) OPERATIONAL
RGA 3 Sniffer (50 V) TDS, LIDS (He) OPERATIONAL
Baratron Gauge Main Main Vessel OPERATIONAL
FR Pressure Gauge Main Main Vessel OPERATIONAL
FR Pressure Gauge Sniffer Sniffer Probe OPERATIONAL
Camera - Open

References

  1. ^ C. Gormezano et al., Lower Hybrid Heating in the WEGA Tokamak, Symposium on Heating in Toroidal Plasma III, Grenoble, France, 22–26 March 1982, 15042735
  2. ^ P. Blanc et al., Lower Hybrid Experiments in the WEGA Tokamak, International Meeting on Theoretical and Experimental Aspects of Heating of Toroidal Plasmas, Grenoble France, 28 June 1976, 8311643
  3. ^ R. Frisch et al., Technological Aspects of the WEGA Stellarator Symposium on Fusion Technology, Garnich-Partenkirchen, F. R. Germany, 14–18 June 1976, FR7602990
  4. ^ T. Consoli et al., The WEGA Stellarator, Bulletin of Information, Science and Technology 202 (1975) 93-100
  5. ^ H. Hailer et al., 14th European Conference on Controlled Fusion and Plasma Physics, Madrid 1987, 11(1) 423
  6. ^ M.Lewerentz et al., First Experiences with the new W7-X Like Control System at the WEGA Stellarator, Fusion Engineering Design 84(7-11) (2009) 1179-1183
  7. ^ J. Schacht et al., Stellarator WEGA as a Test-bed for the Wendelstein 7-X Control System Concept, Fusion Engineering Design 83(2-3) (2008) 228-235
  8. ^ H. Laqua et al., Test of the Steady State W7-X Control and Data Acquisition System at the WEGA Stellarator Fusion Engineering Design 85(3-4) (2010), 520-524
  9. ^ M. Otte et al., The WEGA Stellarator: Results and Prospects, AIP Conference Proceedings 993 (2008), 3
  10. ^ Y. Podoba, Radio Frequency Heating on the WEGA Stellarator IPP report, IPP 13/12, October 2008
  11. ^ Y. Y. Podoba et al., Direct Observation of Electron-Bernstein Wave Heating by O-X-B Mode Conversion at Low Magnetic Fields in the WEGA Stellarator, Physical Review Letters, 98 (2007) 255003
  12. ^ K. Horvath et al., Langmuir Probe Measurements in the WEGA Stellarator, Contributions to Plasma Physics 44(7-8) (2004), 650-655
  13. ^ K. Horvath et al., Investigations of the Electron Temperature Profiles at the WEGA Stellarator, Plasma Physics and Controlled Fusion 48 (2006) 315
  14. ^ M. Otte et al., Overdense Plasma Operation in the WEGA Stellarator, Contributions to Plasma Physics 50(8) (2010) 785-789
  15. ^ J. Chung et al., Time Resolved Coherence-Imaging Spectrometer on WEGA Stellarator Plasma Physics Controlled Fusion, 47 (2005) 919
  16. ^ H. P. Laqua et al., Fundamental Investigation of Electron Bernstein Wave Heating and Current Drive at the WEGA Stellarator, IAEA, EX P-6 18
  17. ^ E. Chlechowitz, Plasma Current and Pressure Measurements at the WEGA Stellarator, PhD, Greifswald, April 2010
  18. ^ L. I. Krupnik et al., The Heavy Ion Beam Probing Development for WEGA Stellarator, Fusion Science and Technology 50(2) (2006), 276-280
  19. ^ Y. Podoba et al., First HIBP Results on the WEGA Stellarator, AIP Conference Proceedings 993 (2008) 235
  20. ^ M. Otte et al., Overview of Recent Results on the WEGA Stellarator Nukleonika 57(2) (2012), 171-175
  21. ^ "WEGA fusion experiment passed on to the USA".
  22. ^ D. Andruczyk et al., HIDRA: Hybrid Illinois Device for Research and Applications, Fusion Science and Technology 68 (2015) 497
  23. ^ D. Johnson et al., HIDRA control system (HCS): A LabVIEW-based program to control the Hybrid Illinois Device for Research and Applications, Fusion Engineering and Design 128 (2018) 215-222
  24. ^ R. Rizkallah et al., Latest Results From the Hybrid Illinois Device for Research and Applications (HIDRA), IEEE Transactions on Plasma Science 46(7) (2018) 2685
  25. ^ R. Rizkallah et al., Mapping of the HIDRA stellarator magnetic flux surfaces, Physics of Plasmas 26 (2019) 092503-1
  26. ^ D. Andruczyk et al., Overview of lithium injection and flowing liquid lithium results from the US–China collaboration on EAST, Physica Scripta T171 (2020) 014067
  27. ^ A. shone et al., An Overview of the Hybrid Illinois Device for Research and Applications Material Analysis Test-stand (HIDRA-MAT), JOurnal of Fusion Energy, 39 (2020), 438-445
  28. ^ A. Shone et al., Liquid Metal Droplet Injector For LM Applications in HIDRA-MAT, Fusion Engineering and Design, Submitted (2021)
  29. ^ A. Shone HYBRID ILLINOIS DEVICE FOR RESEARCH AND APPLICATIONS MATERIAL ANALYSIS TEST-STAND DEVELOPMENT FOR CHARACTERIZATION OF FUSION PLASMA FACING COMPONENT PLASMA-MATERIAL INTERACTIONS, Master Thesis, University of Illinois Urbana-Champaign, 2020
  30. ^ D. Andruczyk et al.,
  31. ^ D. Andruczyk et al., A Domestic Program for Liquid Metal PFC Research in Fusion, Journal of Fusion Energy 39 (2020) 441-447

External links

Retrieved from "https://en.wikipedia.org/w/index.php?title=Hybrid_Illinois_Device_for_Research_and_Applications&oldid=1215719686"