Leap second

Source: Wikipedia, the free encyclopedia.

UTC clock from time.gov
during the leap second on 31 December 2016.

A leap second is a one-

irregularities and long-term slowdown in the Earth's rotation. The UTC time standard, widely used for international timekeeping and as the reference for civil time in most countries, uses TAI and consequently would run ahead of observed solar time unless it is reset to UT1 as needed. The leap second facility exists to provide this adjustment. The leap second was introduced in 1972. Since then, 27 leap seconds have been added to UTC, with the most recent occurring on December 31, 2016.[1]

Because the Earth's rotational speed varies in response to climatic and geological events,[2] UTC leap seconds are irregularly spaced and unpredictable. Insertion of each UTC leap second is usually decided about six months in advance by the International Earth Rotation and Reference Systems Service (IERS), to ensure that the difference between the UTC and UT1 readings will never exceed 0.9 seconds.[3][4]

This practice has proven disruptive, particularly in the twenty-first century and especially in services that depend on precise

process control. And since not all computers are adjusted by leap-second, they will display times differing from those that have been adjusted.[5] After many years of discussions by different standards bodies, in November 2022, at the 27th General Conference on Weights and Measures, it was decided to abandon the leap second by or before 2035.[6][7]

History

Graph showing the difference between UT1 and UTC. Vertical segments correspond to leap seconds.

In about AD 140,

International Committee for Weights and Measures, and in 1960 by the General Conference on Weights and Measures, becoming a part of the International System of Units (SI).[12]

Eventually, this definition too was found to be inadequate for precise time measurements, so in 1967, the

SI second was again redefined as 9,192,631,770 periods of the radiation emitted by a caesium-133 atom in the transition between the two hyperfine levels of its ground state.[13] That value agreed to 1 part in 1010 with the astronomical (ephemeris) second then in use.[14] It was also close[quantify
] to 1⁄86,400 of the mean solar day as averaged between years 1750 and 1892.

However, for the past several centuries, the length of the mean solar day has been increasing by about 1.4–1.7 ms per century, depending on the averaging time.[15][16][17] By 1961, the mean solar day was already a millisecond or two longer than 86400 SI seconds.[18] Therefore, time standards that change the date after precisely 86400 SI seconds, such as the International Atomic Time (TAI), would become increasingly ahead of time standards tied to the mean solar day, such as Universal Time (UT).

When the

UT2, a practice known as the "rubber second".[19] The rate of UTC was decided at the start of each year, and was offset from the rate of atomic time by −150 parts per 1010 for 1960–1962, by −130 parts per 1010 for 1962–63, by −150 parts per 1010 again for 1964–65, and by −300 parts per 1010 for 1966–1971.[20] Alongside the shift in rate, an occasional 0.1 s step (0.05 s before 1963) was needed. This predominantly frequency-shifted rate of UTC was broadcast by MSF, WWV, and CHU among other time stations. In 1966, the CCIR approved "stepped atomic time" (SAT), which adjusted atomic time with more frequent 0.2 s adjustments to keep it within 0.1 s of UT2, because it had no rate adjustments.[21] SAT was broadcast by WWVB among other time stations.[20]

In 1972, the leap-second system was introduced so that the UTC seconds could be set exactly equal to the standard SI second, while still maintaining the UTC time of day and changes of UTC date synchronized with those of UT1.[13] By then, the UTC clock was already 10 seconds behind TAI, which had been synchronized with UT1 in 1958, but had been counting true SI seconds since then. After 1972, both clocks have been ticking in SI seconds, so the difference between their displays at any time is 10 seconds plus the total number of leap seconds that have been applied to UTC as of that time; as of 2024, 27 leap seconds have been applied to UTC, so the difference is 10 + 27 = 37 seconds. The most recent leap second was on December 31, 2016.

Insertion of leap seconds

Announced leap seconds to date[22]
Year 30 Jun 31 Dec
1972 +1 +1
1973 0 +1
1974 0 +1
1975 0 +1
1976 0 +1
1977 0 +1
1978 0 +1
1979 0 +1
1980 0 0
1981 +1 0
1982 +1 0
1983 +1 0
1984 0 0
1985 +1 0
1986 0 0
1987 0 +1
1988 0 0
1989 0 +1
1990 0 +1
1991 0 0
1992 +1 0
1993 +1 0
1994 +1 0
1995 0 +1
1996 0 0
1997 +1 0
1998 0 +1
1999 0 0
2000 0 0
2001 0 0
2002 0 0
2003 0 0
2004 0 0
2005 0 +1
2006 0 0
2007 0 0
2008 0 +1
2009 0 0
2010 0 0
2011 0 0
2012 +1 0
2013 0 0
2014 0 0
2015 +1 0
2016 0 +1
2017 0 0
2018 0 0
2019 0 0
2020 0 0
2021 0 0
2022 0 0
2023 0 0
2024 0
Year 30 Jun 31 Dec
Total 11 16
27
Current TAI − UTC
37

The scheduling of leap seconds was initially delegated to the

Bureau International de l'Heure
(BIH), but passed to the International Earth Rotation and Reference Systems Service (IERS) on 1 January 1988. IERS usually decides to apply a leap second whenever the difference between UTC and UT1 approaches 0.6 s, in order to keep the difference between UTC and UT1 from exceeding 0.9 s.

The UTC standard allows leap seconds to be applied at the end of any UTC month, with first preference to June and December and second preference to March and September. As of May 2023, all of them have been inserted at the end of either 30 June or 31 December. IERS publishes announcements every six months, whether leap seconds are to occur or not, in its "Bulletin C". Such announcements are typically published well in advance of each possible leap second date – usually in early January for 30 June and in early July for 31 December.[23][24] Some time signal broadcasts give voice announcements of an impending leap second.

Between 1972 and 2020, a leap second has been inserted about every 21 months, on average. However, the spacing is quite irregular and apparently increasing: there were no leap seconds in the six-year interval between 1 January 1999 and 31 December 31, 2004 but there were nine leap seconds in the eight years 1972–1979. Since the introduction of leap seconds, 1972 has been the longest year on record: 366 days and two seconds.

Unlike

U.S. Eastern Standard Time and 1 January 2006, 08:59:60 (a.m.) in Japan Standard Time
.

Process

When it is mandated, a positive leap second is inserted between second 23:59:59 of a chosen UTC calendar date and second 00:00:00 of the following date. The definition of UTC states that the last day of December and June are preferred, with the last day of March or September as second preference, and the last day of any other month as third preference.[25] All leap seconds (as of 2019) have been scheduled for either 30 June or 31 December. The extra second is displayed on UTC clocks as 23:59:60. On clocks that display local time tied to UTC, the leap second may be inserted at the end of some other hour (or half-hour or quarter-hour), depending on the local time zone. A negative leap second would suppress second 23:59:59 of the last day of a chosen month so that second 23:59:58 of that date would be followed immediately by second 00:00:00 of the following date. Since the introduction of leap seconds, the mean solar day has outpaced atomic time only for very brief periods and has not triggered a negative leap second.

Slowing rotation of the Earth

See also: ΔT (timekeeping)
Deviation of day length from SI based day with shorter days resulting from faster planetary rotation.

Leap seconds are irregularly spaced because the Earth's rotation speed changes irregularly. Indeed, the Earth's rotation is quite unpredictable in the long term, which explains why leap seconds are announced only six months in advance.

A

period of about 1,500 yr.[17] Over the last few centuries, rate of lengthening of the mean solar day has been about 1.4 ms per century, being the sum of the periodic component and the overall rate.[26]

The main reason for the slowing down of the Earth's rotation is

glacial rebound shortens the solar day by 0.6 ms/century and the 2004 Indian Ocean earthquake is thought to have shortened it by 2.68 microseconds.[27]

It is a mistake, however, to consider leap seconds as indicators of a slowing of Earth's rotation rate; they are indicators of the accumulated difference between atomic time and time measured by Earth rotation.[28] The plot at the top of this section shows that in 1972 the average length of day was approximately 86400.003 seconds and in 2016 it was approximately 86400.001 seconds, indicating an overall increase in Earth's rotation rate over that time period. Positive leap seconds were inserted during that time because the annual average length of day remained greater than 86400 SI seconds, not because of any slowing of Earth's rotation rate.[29]

In 2021, it was reported that Earth was spinning faster in 2020 and experienced the 28 shortest days since 1960, each of which lasted less than 86399.999 seconds.[30] This caused engineers worldwide to discuss a negative leap second and other possible timekeeping measures, some of which could eliminate leap seconds.[31]

Future of leap seconds

The TAI and UT1 time scales are precisely defined, the former by atomic clocks (and thus independent of Earth's rotation) and the latter by astronomical observations (that measure actual planetary rotation and thus the solar time at the Greenwich meridian). UTC (on which civil time is usually based) is a compromise, stepping with atomic seconds but periodically reset by a leap second to match UT1.

The irregularity and unpredictability of UTC leap seconds is problematic for several areas, especially computing (see below). With increasing requirements for timestamp accuracy in systems such as process automation and high-frequency trading,[32] this raises a number of issues. Consequently, the long-standing practice of inserting leap seconds is under review by the relevant international standards body.[33]

International proposals for elimination of leap seconds

On 5 July 2005, the Head of the Earth Orientation Center of the IERS sent a notice to IERS Bulletins C and D subscribers, soliciting comments on a U.S. proposal before the ITU-R Study Group 7's WP7-A to eliminate leap seconds from the UTC broadcast standard before 2008 (the ITU-R is responsible for the definition of UTC).[b] It was expected to be considered in November 2005, but the discussion has since been postponed.[35] Under the proposal, leap seconds would be technically replaced by leap hours as an attempt to satisfy the legal requirements of several ITU-R member nations that civil time be astronomically tied to the Sun.

A number of objections to the proposal have been raised. P. Kenneth Seidelmann, editor of the Explanatory Supplement to the Astronomical Almanac, wrote a letter lamenting the lack of consistent public information about the proposal and adequate justification.[36] In an op-ed for Science News, Steve Allen of the University of California, Santa Cruz said that the process has a large impact on astronomers.[37] Allen has an extensive online site devoted to the issues and the history of leap seconds,[38] including a set of references about the proposal and arguments against it.[39]

At the 2014 General Assembly of the International Union of Radio Scientists (URSI), Demetrios Matsakis, the United States Naval Observatory's Chief Scientist for Time Services, presented the reasoning in favor of the redefinition and rebuttals to the arguments made against it.[40] He stressed the practical inability of software programmers to allow for the fact that leap seconds make time appear to go backwards, particularly when most of them do not even know that leap seconds exist. The possibility of leap seconds being a hazard to navigation was presented, as well as the observed effects on commerce.

The United States formulated its position on this matter based upon the advice of the National Telecommunications and Information Administration[41] and the Federal Communications Commission (FCC), which solicited comments from the general public.[42] This position is in favor of the redefinition.[43][c]

In 2011, Chunhao Han of the Beijing Global Information Center of Application and Exploration said China had not decided what its vote would be in January 2012, but some Chinese scholars consider it important to maintain a link between civil and astronomical time due to Chinese tradition. The 2012 vote was ultimately deferred.[45] At an ITU/BIPM-sponsored workshop on the leap second, Han expressed his personal view in favor of abolishing the leap second,[46] and similar support for the redefinition was again expressed by Han, along with other Chinese timekeeping scientists, at the URSI General Assembly in 2014.

At a special session of the Asia-Pacific Telecommunity Meeting on 10 February 2015, Chunhao Han indicated China was now supporting the elimination of future leap seconds, as were all the other presenting national representatives (from Australia, Japan, and the Republic of Korea). At this meeting, Bruce Warrington (NMI, Australia) and Tsukasa Iwama (NICT, Japan) indicated particular concern for the financial markets due to the leap second occurring in the middle of a workday in their part of the world.[d] Subsequent to the CPM15-2 meeting in March/April 2015 the draft gives four methods which the WRC-15 might use to satisfy Resolution 653 from WRC-12.[49]

Arguments against the proposal include the unknown expense of such a major change and the fact that universal time will no longer correspond to mean solar time. It is also answered that two timescales that do not follow leap seconds are already available,

IS-95 and CDMA2000. In general, computer systems use UTC and synchronize their clocks using Network Time Protocol (NTP). Systems that cannot tolerate disruptions caused by leap seconds can base their time on TAI and use Precision Time Protocol. However, the BIPM has pointed out that this proliferation of timescales leads to confusion.[50]

At the 47th meeting of the Civil Global Positioning System Service Interface Committee in

Fort Worth, Texas, in September 2007, it was announced that a mailed vote would go out on stopping leap seconds. The plan for the vote was:[51]

In January 2012, rather than decide yes or no per this plan, the ITU decided to postpone a decision on leap seconds to the World Radiocommunication Conference in November 2015. At this conference, it was again decided to continue using leap seconds, pending further study and consideration at the next conference in 2023.[53]

In October 2014, Włodzimierz Lewandowski, chair of the timing subcommittee of the Civil GPS Interface Service Committee and a member of the ESA Navigation Program Board, presented a CGSIC-endorsed resolution to the ITU that supported the redefinition and described leap seconds as a "hazard to navigation".[54]

Some of the objections to the proposed change have been addressed by its supporters. For example, Felicitas Arias, who, as Director of the International Bureau of Weights and Measures (BIPM)'s Time, Frequency, and Gravimetry Department, was responsible for generating UTC, noted in a press release that the drift of about one minute every 60–90 years could be compared to the 16-minute annual variation between true solar time and mean solar time, the one hour offset by use of daylight time, and the several-hours offset in certain geographically extra-large time zones.[55]

Proposed alternatives to the leap second are the leap hour, which requires changes only once every few centuries;[56] and the leap minute, with changes coming every half-century.[1][57]

On 18 November 2022, the

GPS, which does not adjust its time with leap seconds, Russia's system, GLONASS, does adjust its time with leap seconds.[6][7]

ITU World Radiocommunication Conference 2023 (WRC-23), which was held in Dubai (United Arab Emirates) from 20 November to 15 December 2023 formally recognized the Resolution 4 of the 27th CGPM (2022) which decides that the maximum value for the difference (UT1-UTC) will be increased in, or before, 2035.[58]

Issues created by insertion (or removal) of leap seconds

Calculation of time differences and sequence of events

To compute the elapsed time in seconds between two given UTC dates requires the consultation of a table of leap seconds, which needs to be updated whenever a new leap second is announced. Since leap seconds are known only 6 months in advance, time intervals for UTC dates further in the future cannot be computed.

Missing leap seconds announcement

Although

IRIG-B, PTP) announce leap seconds at most 12 hours in advance,[citation needed][59] sometimes only in the last minute and some even not at all (DNP 03).[citation needed
]

Implementation differences

Not all clocks implement leap seconds in the same manner. Leap seconds in Unix time are commonly implemented by repeating 23:59:59 or adding the time-stamp 23:59:60. Network Time Protocol (SNTP) freezes time during the leap second,[60] some time servers declare "alarm condition".[citation needed] Other schemes smear time in the vicinity of a leap second, spreading out the second of change over a longer period. This aims to avoid any negative effects of a substantial (by modern standards) step in time.[61][62] This approach has led to differences between systems, as leap smear is not standardized and several different schemes are used in practice.[63]

Textual representation of the leap second

The textual representation of a leap second is defined by BIPM as "23:59:60". There are programs that are not familiar with this format and may report an error when dealing with such input.

Binary representation of the leap second

Most computer operating systems and most time distribution systems represent time with a binary counter indicating the number of seconds elapsed since an arbitrary

epoch; for instance, since 1970-01-01 00:00:00 in POSIX machines or since 1900-01-01 00:00:00 in NTP. This counter does not count positive leap seconds, and has no indicator that a leap second has been inserted, therefore two seconds in sequence will have the same counter value. Some computer operating systems, in particular Linux, assign to the leap second the counter value of the preceding, 23:59:59 second (59–59–0 sequence), while other computers (and the IRIG-B time distribution) assign to the leap second the counter value of the next, 00:00:00 second (59–0–0 sequence).[citation needed] Since there is no standard governing this sequence, the timestamp of values sampled at exactly the same time can vary by one second. This may explain flaws in time-critical systems that rely on timestamped values.[64]

Other reported software problems associated with the leap second

Several models of global navigation satellite receivers have software flaws associated with leap seconds:

Several software vendors have distributed software that has not properly functioned with the concept of leap seconds:

Some businesses and service providers have been impacted by leap-second related software bugs:

There were misplaced concerns that farming equipment using GPS navigation during harvests occurring on 31 December 2016, would be affected by the 2016 leap second.

GPS time, which is not impacted by the leap second.[87]

Due to a software error, the UTC time broadcast by the NavStar GPS system was incorrect by about 13 microseconds on 25–26 January 2016.[88][89]

Workarounds for leap second problems

The most obvious workaround is to use the TAI scale for all operational purposes and convert to UTC for human-readable text. UTC can always be derived from TAI with a suitable table of leap seconds. The Society of Motion Picture and Television Engineers (SMPTE) video/audio industry standards body selected TAI for deriving timestamps of media.[90] IEC/IEEE 60802 (Time sensitive networks) specifies TAI for all operations. Grid automation is planning to switch to TAI for global distribution of events in electrical grids. Bluetooth mesh networking also uses TAI.[91]

Instead of inserting a leap second at the end of the day, Google servers implement a "leap smear", extending seconds slightly over a 24-hour period centered on the leap second.[62] Amazon followed a similar, but slightly different, pattern for the introduction of the 30 June 2015, leap second,[92] leading to another case of the proliferation of timescales. They later released an NTP service for EC2 instances which performs leap smearing.[93] UTC-SLS was proposed as a version of UTC with linear leap smearing, but it never became standard.[94]

It has been proposed that media clients using the Real-time Transport Protocol inhibit generation or use of NTP timestamps during the leap second and the second preceding it.[95]

NIST has established a special NTP time server to deliver UT1 instead of UTC.[96] Such a server would be particularly useful in the event the ITU resolution passes and leap seconds are no longer inserted.[97] Those astronomical observatories and other users that require UT1 could run off UT1 – although in many cases these users already download UT1-UTC from the IERS, and apply corrections in software.[98]

See also

  • Clock drift, phenomenon where a clock gains or loses time compared to another clock
  • DUT1, which describes the difference between coordinated universal time (UTC) and universal time (UT1)
  • Dynamical time scale
  • Leap year, a year containing one extra day or month

Notes

  1. ^ Only the Gregorian calendar's leap days begin after 28 February. The leap days of other calendars begin at different local times in their own years (Ethiopian calendar, Iranian calendars, Indian national calendar, etc.).
  2. ^ The Wall Street Journal noted that the proposal was considered by a U.S. official at the time to be a "private matter internal to the ITU."[34]
  3. ^ The FCC has posted its received comments, which can be found using their search engine for proceeding 04–286 and limiting the "received period" to those between 27 January and 18 February 2014, inclusive.[44]
  4. ^ In addition to publishing the video of the special session,[47] the Australian Communications and Media Authority has a transcript of that session and a web page with draft content of the Conference Preparatory Meeting report and solutions for ITU-R WRC-15 Agenda Item 1.14.[48]

References

  1. ^ a b Martin, Cassie (19 January 2024). "50 years ago, timekeepers deployed the newly invented leap second". 50 Years Ago. Science News. p. 4.
  2. IERS. 2013. Archived
    from the original on 29 August 2016. Retrieved 6 August 2016.
  3. IERS. Archived
    from the original on 30 May 2015. Retrieved 5 January 2015.
  4. ^ James Vincent (7 January 2015). "2015 is getting an extra second and that's a bit of a problem for the internet". The Verge. Archived from the original on 17 March 2017.
  5. S2CID 118403321
    .
  6. ^ a b "Do not adjust your clock: scientists call time on the leap second". World News. The Guardian. Agence France-Presse. 18 November 2022.
  7. ^
    PMID 36400956
    .
  8. ISBN 978-0-691-00260-6
    .
  9. ^ al-Biruni (1879). The chronology of ancient nations: an English version of the Arabic text of the Athâr-ul-Bâkiya of Albîrûnî, or "Vestiges of the Past". Sachau, C. Edward. Oriental Translation Fund of Great Britain & Ireland. pp. 141–149, 158, 408, 410. Archived from the original on 14 November 2017. Used for mean new moons, both in Hebrew calendar cycles and in equivalent astronomical cycles.
  10. ^ Everett, J. D. (1875). Illustrations of the centimetre-gramme-second (C.G.S.) system of units. Taylor and Francis. p. 83.
  11. Bibcode:1928JRASC..22..145P
    .
  12. ISBN 0-935702-68-7. Archived
    from the original on 14 November 2017.
  13. ^ a b "Leap Seconds". Time Service Department, United States Naval Observatory. Retrieved 19 November 2022.
  14. ^ Wm Markowitz (1988) 'Comparisons of ET (Solar), ET (Lunar), UT and TDT', in (eds.) A K Babcock & G A Wilkins, 'The Earth's Rotation and Reference Frames for Geodesy and Geophysics', IAU Symposia #128 (1988), at pp 413–418.
  15. ^ DD McCarthy and AK Babcock (1986), "The Length of the Day Since 1658", Phys. Earth Planet Inter., No. 44, pp. 281–292
  16. ^ RA Nelson, DD McCarthy, S Malys, J Levine, B Guinot, HF Fliegel, RL Beard, and TR Bartholomew, (2001) "The Leap Second: its History and Possible Future" (2001), Metrologia 38, pp. 509–529
  17. ^
    S2CID 120718607
    .
  18. doi:10.1088/0004-6256/136/5/1906. Archived
    (PDF) from the original on 12 March 2021. Retrieved 26 February 2022.
  19. ^ Jespersen, James; Fitz-Randolph, Jane (1999). From Sundials To Atomic Clocks: Understanding Time and Frequency (PDF). National Institute of Standards and Technology. p. 109.
  20. ^ a b Blair, Byron E., ed. (May 1974), NBS Monograph 140: Time and Frequency: Theory and Fundamentals (PDF), p. 8
  21. ^ McCarthy, Dennis D.; Seidelmann, P. Kenneth. Time: From Earth Rotation to Atomic Physics (second ed.). For provisional limited use, the CCIR in 1966 approved "Stepped Atomic Time," which used the atomic second with frequent 200 ms adjustments made in order to be within 0.1 s of UT2.
  22. ^ "TAI−UTC (1972-01-01 – 2024-06-28)". 4 July 2023. Retrieved 4 July 2023.
  23. ^ Gambis, Daniel (4 July 2008). "Bulletin C 36". Paris: IERS EOP PC, Observatoire de Paris. Archived from the original on 6 October 2009. Retrieved 18 April 2010.
  24. ^ Andrea Thompson (8 December 2008). "2008 Will Be Just a Second Longer". Live Science. Archived from the original on 12 December 2008. Retrieved 29 December 2008.
  25. ^ "International Telecommunication Union Radiocommunications sector recommendation TF.460-6: Standard-frequency and time-signal emissions". Archived from the original on 17 October 2016. Retrieved 9 February 2017.
  26. ^ Steve Allen (8 June 2011). "Extrapolations of the difference (TI – UT1)". ucolick.org. Archived from the original on 4 March 2016. Retrieved 29 February 2016.
  27. National Aeronautics and Space Administration (press release). Archived
    from the original on 27 January 2011.
  28. ^ Chester, Geoff (15 June 2015). "Wait a second… 2015 will be a little longer". CHIPS Articles: The Department of the Navy's Information Technology Magazine. Retrieved 4 March 2021.
  29. ^ Plait, Phil (31 December 2008). "Followup: Leap Seconds". Discover Magazine: Bad Astronomy. Retrieved 5 March 2021.
  30. ^ Jones, Graham; Bikos, Konstantin (6 January 2021) [2020-12-23]. "Earth is in a hurry in 2020". timeanddate.com. Retrieved 6 March 2021.
  31. ^ Knapton, Sarah (4 January 2021). "The Earth is spinning faster now than at any time in the past half century". The Daily Telegraph. Archived from the original on 12 January 2022. Retrieved 11 February 2021.
  32. ^ "Time Split to the Nanosecond Is Precisely What Wall Street Wants". The New York Times. 29 June 2018. Retrieved 13 December 2022.
  33. ^ Dwyer, Colin (29 December 2016). "With A Leap Second, 2016 Promises To Linger Just A Little Bit Longer". NPR. Archived from the original on 2 January 2023. Retrieved 24 February 2023.
  34. ^ "Why the U.S. Wants To End the Link Between Time and Sun". The Wall Street Journal. Archived from the original on 7 November 2017. Retrieved 31 October 2017.
  35. ^ "Leap second talks are postponed". BBC News. Archived from the original on 7 November 2017. Retrieved 31 October 2017.
  36. ^ P. Kenneth Seidelmann. "UTC redefinition or change". IGS Mail (Mailing list).
  37. ^ Cowen, Ron (22 April 2006). "To Leap or Not to Leap: Scientists debate a timely issue". Science News. Archived from the original on 26 May 2023. Retrieved 26 May 2023.
  38. ^ Steve Allen. "UTC might be redefined without Leap Seconds". Archived from the original on 3 June 2017. Retrieved 31 October 2017.
  39. ^ "nc1985wp7a Proposed US Contribution to ITU-R WP 7A". Archived from the original on 1 January 2017. Retrieved 31 October 2017.
  40. ^ Demetrios Matsakis (18 August 2014). "Comments on the Debate over the Proposal to Redefine UTC" (PDF). Archived (PDF) from the original on 8 February 2017. Retrieved 31 October 2017.
  41. ^ "United States Proposals, Proposal for the Work of the Conference, Agenda Item 1.14" (PDF). National Telecommunications and Information Administration.
  42. ^ "FCC Seeks Comment On Recommendations Approved By The Advisory Committee For The 2015 World Radiocommunication Conference" (PDF). Federal Communications Commission. 28 January 2014. Archived (PDF) from the original on 29 July 2014.
  43. ^ "Preliminary Views and Proposals Regarding WRC-15 Agenda Items" (PPT). Organization of American States. Archived from the original on 29 July 2014.
  44. ^ "Search for Filings Results". fcc.gov. Archived from the original on 1 July 2015.
  45. S2CID 8220495
    .
  46. ^ Han, Chunhao (19 September 2013). "Conception, Definition and Realization of Time Scale in GNSS" (PDF). Archived (PDF) from the original on 5 September 2014.
  47. ^ Information Session on the WRC-15 agenda item 1.14 – Coordinated Universal Time (UTC). YouTube. 15 April 2015. Archived from the original on 18 November 2015.
  48. ^ "WRC-15 Agenda item 1.14: Coordinated Universal Time (UTC)". acma.gov.au. Archived from the original on 8 September 2015.
  49. ^ "RESOLUTION 653 (WRC-12) Future of the Coordinated Universal Time time-scale" (PDF). International Telecommunication Union. Archived (PDF) from the original on 2 July 2015.
  50. ^ CCTF Strategy Document, International Bureau of Weights and Measures, May 2016, pp. 21–25
  51. ^ "47th CGSIC Meeting – Timing Subcommittee" (PDF). 25 September 2007. p. 9. Archived from the original (PDF) on 14 June 2011. Retrieved 18 November 2007.
  52. ^ "WP7D – Status of Coordinated Universal Time (UTC) study in ITU-R" (Word 2007). International Telecommunication Union – Radiocommunication Sector (ITU-R) Release: 2. 4 October 2011. Archived from the original on 23 March 2014. Retrieved 24 October 2011. To date, the BR received replies from 16 different Member States for the latest survey (out of a total of 192 Member States, 55 of which participate in the formation of UTC) – 13 being in favor of the change, 3 being contrary.
  53. ^ "Coordinated Universal Time (UTC) to retain 'leap second'" (Press release). International Telecommunication Union. 19 November 2015. Archived from the original on 29 January 2016.
  54. ^ "CGSIC opinion on the redefinition of UTC now under consideration by the International Telecommunication Union (ITU)". Archived from the original on 23 October 2014.
  55. BIPM. 13 October 2011. Archived
    (PDF) from the original on 18 January 2015.
  56. ^ "Scientists propose 'leap hour' to fix time system". New Scientist. 14 May 2012 [2008-12-18]. Retrieved 3 September 2022 – via The New Indian Express.
  57. ISSN 0362-4331
    . Retrieved 23 January 2024.
  58. ^ "ITU-R and BIPM work together at the World Radiocommunication Conference". BIPM.
  59. doi:10.6028/NIST.TN.2187
    .
  60. ^ "NIST Internet Time Service (ITS)". NIST. 10 February 2010.
  61. RFC 7164
  62. ^ a b "Leap Smear". Google Inc. Retrieved 26 May 2023.
  63. ^ Dimarcq, Noël; Tavella, Patrizia (17 November 2022). "Draft Resolution D: 'On the use and future development of UTC'". Bureau International des Poids et Mesures. p. 7.
  64. PMID 20396403
    .
  65. ^ "256-Week Leap Second Bug". 2 July 2013. Archived from the original on 4 March 2016.
  66. ^ "Motorola Oncore receivers and Leap Second bug". 2 July 2013. Archived from the original on 18 January 2013.
  67. ^ "Leap-second problem with older GPS receivers". 19 November 2014. Archived from the original on 29 November 2014.
  68. ^ "How Leap Seconds Can Interfere with GNSS Receivers". 13 May 2015. Archived from the original on 6 March 2016.
  69. ^ "Symmetricom TymServe 2100-GPS currently fails with GPS offset". time-nuts (Mailing list). Archived from the original on 17 February 2015.
  70. ^ "BeiDou Numbering Presents Leap-Second Issue". GPS World. 3 March 2015.
  71. ^ Malone, David. "NTP Leap Bits". Archived from the original on 22 July 2014. Retrieved 1 December 2019.
  72. ^ Malone, David (2016). "The Leap Second Behaviour of NTP Servers" (PDF). Proc.Traffic Monitoring and Analysis workshop. Archived (PDF) from the original on 23 October 2016. Retrieved 23 October 2016.
  73. hdl:10453/130538
    .
  74. hdl:10453/43923
    .
  75. ^ "NTP Events". satsignal.eu. Archived from the original on 18 July 2014.
  76. ^ "'Leap Second' Bug Wreaks Havoc Across Web". Wired. 1 July 2012. Archived from the original on 28 March 2014.
  77. ^ "Leap second crashes Qantas and leaves passengers stranded". News Limited. 1 July 2012. Archived from the original on 1 July 2012.
  78. ^ "Anyone else experiencing high rates of Linux server crashes during a leap second day?". Serverfault.com. Archived from the original on 9 July 2012.
  79. ^ Shulman, Eden. "Beta Boston". Boston Globe. Archived from the original on 29 September 2015. Retrieved 27 September 2015.
  80. ^ "Cisco Bug: CSCub38654 – N5K: Switch hang/lock up may occur due to Leap second update". Cisco. 24 July 2015. Archived from the original on 8 March 2016.
  81. ^ Sarah Knapton (1 July 2015). "Leap Second confuses Twitter and Android". The Daily Telegraph. Archived from the original on 6 October 2015.
  82. ^ Clarke, Gavin (8 August 2016). "Power cut crashes Delta's worldwide flight update systems". The Register. Archived from the original on 4 January 2017. Retrieved 3 January 2017.
  83. ^ "How and why the leap second affected Cloudflare DNS". Cloudflare. 1 January 2017. Archived from the original on 2 January 2017.
  84. ^ "#12914 runtime: time: expose monotonic clock source". GitHub. Archived from the original on 20 March 2017. Retrieved 5 January 2017.
  85. ^ "ICE Market Update – Leap Second Impact". Intercontinental Exchange. Archived from the original on 5 May 2015.
  86. ^ "Got a second – the world time needs it". ABC Rural. 30 December 2016. Archived from the original on 2 January 2017. Retrieved 3 January 2017.
  87. ^ How fast is the earth moving? Rhett Herman, a physics professor at Radford University in Virginia, supplies the following answer, Scientific American, 26 October 1998
  88. ^ "Air Force Official Press Release – GPS Ground System Anomaly" (PDF).
  89. ^ Yao, Jian; Lombardi, Michael A.; Novick, Andrew N.; Patla, Bijunath; Sherman, Jeff A.; Zhang, Victor. "The effects of the January 2016 UTC offset anomaly on GPS-controlled clocks monitored at NIST" (PDF).
  90. ^ Paul Briscoe (14 May 2013). "Network-Based Timing and Synchronization" (PDF).
  91. ^ "Mesh Model Bluetooth® Specification" (PDF download). Bluetooth Technology Website. 13 July 2017. Retrieved 14 December 2019. See sections 5.1.1 and A.1.
  92. ^ Jeff Barr (18 May 2015). "Look Before You Leap – The Coming Leap Second and AWS (Updated)". Amazon Web Services.
  93. ^ Randall Hunt (29 November 2017). "Keeping Time With Amazon Time Sync Service". Amazon Web Services. Retrieved 8 March 2018.
  94. ^ Kuhn, Markus (2005). "UTC with Smoothed Leap Seconds (UTC-SLS)". www.cl.cam.ac.uk.
  95. doi:10.17487/RFC7164. RFC 7164
    .
  96. ^ "UT1 NTP Time Dissemination". National Institute of Standards and Technology. 11 December 2015. Retrieved 31 August 2019.
  97. ^ Wallace, Patrick (2003). "The UTC Problem and its Solution" (PDF). Proceedings of Colloquium on the UTC Time Scale. Torino. Archived (PDF) from the original on 18 January 2015.
  98. ^ Luzum, Brian (2013). The Role of the IERS in the Leap Second (PDF). BIPM/ITU Workshop on the Future of the International Time Scale. Archived (PDF) from the original on 15 July 2014.

Further reading

External links

Wikimedia Commons has media related to Leap second.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Leap_second&oldid=1214622254"