Liquid–liquid extraction

This article may be too technical for most readers to understand. Please help improve it to make it understandable to non-experts, without removing the technical details. (August 2022) (Learn how and when to remove this template message)

Liquid–liquid extraction, also known as solvent extraction and partitioning, is a method to separate compounds or

The term partitioning is commonly used to refer to the underlying chemical and physical processes involved in liquid–liquid extraction, but on another reading may be fully synonymous with it. The term solvent extraction can also refer to the separation of a substance from a mixture by preferentially dissolving that substance in a suitable solvent. In that case, a soluble compound is separated from an insoluble compound or a complex matrix.^{[not verified in body]}

From a hydrometallurgical perspective, solvent extraction is exclusively used in separation and purification of uranium and plutonium, zirconium and hafnium, separation of cobalt and nickel, separation and purification of rare earth elements etc., its greatest advantage being its ability to selectively separate out even very similar metals. One obtains high-purity single metal streams on 'stripping' out the metal value from the 'loaded' organic wherein one can precipitate or deposit the metal value. Stripping is the opposite of extraction: Transfer of mass from organic to aqueous phase.

Liquid-liquid extraction is also widely used in the production of fine

]

Measures of effectiveness

This section needs additional citations for verification. Please help improve this article by adding citations to reliable sources in this section. Unsourced material may be challenged and removed. (May 2014) (Learn how and when to remove this template message)

Distribution ratio

In solvent extraction, a distribution ratio is often quoted as a measure of how well-extracted a species is. The distribution ratio (K_d) is equal to the

Sometimes, the distribution ratio is referred to as the partition coefficient, which is often expressed as the logarithm. Note that a distribution ratio for uranium and neptunium between two inorganic solids (zirconolite and perovskite) has been reported.^[2] In solvent extraction, two immiscible liquids are shaken together. The more polar solutes dissolve preferentially in the more polar solvent, and the less polar solutes in the less polar solvent. In this experiment, the nonpolar halogens preferentially dissolve in the non-polar mineral oil.^[3]

Although the distribution ratio and partition coefficient are often used synonymously, they are not necessarily so. Solutes may exist in more than one form in any particular phase, which would mean that the partition coefficient (K_d) and distribution ratio (D) will have different values. This is an important distinction to make as whilst the partition coefficient has a fixed value for the partitioning of a solute between two phases, the distribution ratio changes with differing conditions in the solvent.^[4]

After performing liquid–liquid extraction, a quantitative measure must be taken to determine the ratio of the solution's total concentration in each phase of the extraction. This quantitative measure is known as the distribution ratio or distribution coefficient.^[5]

Separation factors

The separation factor is one distribution ratio divided by another; it is a measure of the ability of the system to separate two solutes. For instance, if the distribution ratio for nickel (D_Ni) is 10 and the distribution ratio for silver (D_Ag) is 100, then the silver/nickel separation factor (SF_Ag/Ni) is equal to D_Ag/D_Ni = SF_Ag/Ni = 10.^[6]

Decontamination factor

This is used to express the ability of a process to remove a

Success of liquid–liquid extraction is measured through separation factors and decontamination factors. The best way to understand the success of an extraction column is through the liquid–liquid equilibrium (LLE) data set. The data set can then be converted into a curve to determine the steady state partitioning behavior of the solute between the two phases. The y-axis is the concentration of solute in the extract (solvent) phase, and the x-axis is the concentration of the solute in the raffinate phase. From here, one can determine steps for optimization of the process.[7]

Techniques

This section needs additional citations for verification. Please help improve this article by adding citations to reliable sources in this section. Unsourced material may be challenged and removed. (May 2014) (Learn how and when to remove this template message)

Batchwise single stage extractions

This is commonly used on the small scale in chemical labs. It is normal to use a

Dispersive liquid–liquid microextraction (DLLME)

A process used to extract small amounts of organic compounds from water samples.^[8] This process is done by injecting small amounts of an appropriate extraction solvent (C₂Cl₄) and a disperser solvent (acetone) into the aqueous solution. The resulting solution is then centrifuged to separate the organic and aqueous layers. This process is useful in extraction organic compounds such as organochloride and organophsophorus pesticides, as well as substituted benzene compounds from water samples.^[8]

Direct organic extraction

By mixing partially organic soluble samples in organic solvent (toluene, benzene, xylene), the organic soluble compounds will dissolve into the solvent and can be separated using a separatory funnel. This process is valuable in the extraction of proteins and specifically phosphoprotein and phosphopeptide phosphatases.^[9]

Another example of this application is extracting anisole from a mixture of water and 5% acetic acid using ether, then the anisole will enter the organic phase. The two phases would then be separated. The acetic acid can then be scrubbed (removed) from the organic phase by shaking the organic extract with sodium bicarbonate. The acetic acid reacts with the sodium bicarbonate to form sodium acetate, carbon dioxide, and water.

Caffeine can also be extracted from coffee beans and tea leaves using a direct organic extraction. The beans or leaves can be soaked in ethyl acetate which favorably dissolves the caffeine, leaving a majority of the coffee or tea flavor remaining in the initial sample.^[10]

Multistage countercurrent continuous processes

These are commonly used in

Multistage countercurrent arrays have been used for the separation of lanthanides. For the design of a good process, the distribution ratio should be not too high (>100) or too low (<0.1) in the extraction portion of the process. It is often the case that the process will have a section for scrubbing unwanted metals from the organic phase, and finally a stripping section to obtain the metal back from the organic phase.

Mixer–settlers

Battery of mixer-settlers counter currently interconnected. Each mixer-settler unit provides a single stage of extraction. A mixer settler consists of a first stage that mixes the phases together followed by a quiescent settling stage that allows the phases to separate by gravity.

A novel settling device, Sudhin BioSettler, can separate an oil-water emulsion continuously at a much faster rate than simple gravity settlers. In this photo, an oil-water emulsion, stirred by an impeller in an external reservoir and pumped continuously into the two bottom side ports of BioSettler, is separated very quickly into a clear organic (mineral oil) layer exiting via the top of BioSettler and an aqueous (coloured with a red food dye) layer being pumped out continuously from the bottom of BioSettler.

In the multistage countercurrent process, multiple mixer settlers are installed with mixing and settling chambers located at alternating ends for each stage (since the outlet of the settling sections feed the inlets of the adjacent stage's mixing sections). Mixer-settlers are used when a process requires longer residence times and when the solutions are easily separated by gravity. They require a large facility footprint, but do not require much headspace, and need limited remote maintenance capability for occasional replacement of mixing motors. (Colven, 1956; Davidson, 1957)^[12]

Centrifugal extractors

Centrifugal extractors mix and separate in one unit. Two liquids will be intensively mixed between the spinning rotor and the stationary housing at speeds up to 6000 RPM. This develops great surfaces for an ideal mass transfer from the aqueous phase into the organic phase. At 200–2000 g, both phases will be separated again. Centrifugal extractors minimize the solvent in the process, optimize the product load in the solvent and extract the aqueous phase completely. Counter current and cross current extractions are easily established.^[13]

Extraction without chemical change

Some solutes such as

. Here, it is often the case that the carboxylic acid will form a dimer in the organic layer so the distribution ratio will change as a function of the acid concentration (measured in either phase).

For this case, the extraction constant k is described by k = [HA_organic]²/[HA_aqueous]

Solvation mechanism

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (May 2014) (Learn how and when to remove this template message)

Using solvent extraction it is possible to extract

Types of aqueous two-phase extractions

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (March 2014) (Learn how and when to remove this template message)

Polymer–polymer systems. In a Polymer–polymer system, both phases are generated by a dissolved polymer. The heavy phase will generally be a polysaccharide, and the light phase is generally Polyethylene glycol (PEG). Traditionally, the polysaccharide used is dextran. However, dextran is relatively expensive, and research has been exploring using less expensive polysaccharides to generate the heavy phase. If the target compound being separated is a protein or enzyme, it is possible to incorporate a ligand to the target into one of the polymer phases. This improves the target's affinity to that phase, and improves its ability to partition from one phase into the other. This, as well as the absence of solvents or other denaturing agents, makes polymer–polymer extractions an attractive option for purifying proteins. The two phases of a polymer–polymer system often have very similar densities, and very low surface tension between them. Because of this, demixing a polymer–polymer system is often much more difficult than demixing a solvent extraction. Methods to improve the demixing include centrifugation, and application of an electric field.

Polymer–salt systems. Aqueous two-phase systems can also be generated by generating the heavy phase with a concentrated salt solution. The polymer phase used is generally still PEG. Generally, a kosmotropic salt, such as Na₃PO₄ is used, however PEG–NaCl systems have been documented when the salt concentration is high enough. Since polymer–salt systems demix readily they are easier to use. However, at high salt concentrations, proteins generally either denature, or precipitate from solution. Thus, polymer–salt systems are not as useful for purifying proteins.

Ionic liquids systems.

DNA purification

The ability to purify DNA from a sample is important for many modern biotechnology processes. However, samples often contain nucleases that degrade the target DNA before it can be purified. It has been shown that DNA fragments will partition into the light phase of a polymer–salt separation system. If ligands known to bind and deactivate nucleases are incorporated into the polymer phase, the nucleases will then partition into the heavy phase and be deactivated. Thus, this polymer–salt system is a useful tool for purifying DNA from a sample while simultaneously protecting it from nucleases.^{[citation needed]}

Food industry

The PEG–NaCl system has been shown to be effective at partitioning small molecules, such as peptides and nucleic acids. These compounds are often flavorants or odorants. The system could then be used by the food industry to isolate or eliminate particular flavors. Caffeine extraction used to be done using liquid–liquid extraction, specifically direct and indirect liquid–liquid extraction (Swiss Water Method), but has since moved towards super-critical CO₂ as it is cheaper and can be done on a commercial scale.^[17][18]

Analytical chemistry

Often there are chemical species present or necessary at one stage of sample processing that will interfere with the analysis. For example, some air monitoring is performed by drawing air through a small glass tube filled with sorbent particles that have been coated with a chemical to stabilize or derivatize the analyte of interest. The coating may be of such a concentration or characteristics that it would damage the instrumentation or interfere with the analysis. If the sample can be extracted from the sorbent using a nonpolar solvent (such as toluene or carbon disulfide), and the coating is polar (such as HBr or phosphoric acid) the dissolved coating will partition into the aqueous phase. Clearly the reverse is true as well, using polar extraction solvent and a nonpolar solvent to partition a nonpolar interferent. A small aliquot of the organic phase (or in the latter case, polar phase) can then be injected into the instrument for analysis.

Purification of amines

Amines (analogously to ammonia) have a lone pair of electrons on the nitrogen atom that can form a relatively weak bond to a hydrogen atom. It is therefore the case that under acidic conditions amines are typically protonated, carrying a positive charge and under basic conditions they are typically deprotonated and neutral. Amines of sufficiently low molecular weight are rather polar and can form hydrogen bonds with water and therefore will readily dissolve in aqueous solutions. Deprotonated amines on the other hand, are neutral and have greasy, nonpolar organic substituents, and therefore have a higher affinity for nonpolar inorganic solvents. As such purification steps can be carried out where an aqueous solution of an amine is neutralized with a base such as sodium hydroxide, then shaken in a separatory funnel with a nonpolar solvent that is immiscible with water. The organic phase is then drained off. Subsequent processing can recover the amine by techniques such as recrystallization, evaporation or distillation; subsequent extraction back to a polar phase can be performed by adding HCl and shaking again in a separatory funnel (at which point the ammonium ion could be recovered by adding an insoluble counterion), or in either phase, reactions could be performed as part of a chemical synthesis.

Temperature swing solvent extraction

Temperature swing solvent extraction is an experimental technique for the desalination of drinking water. It has been used to remove up to 98.4% of the salt content in water, and is able to process hypersaline brines that cannot be desalinated using reverse osmosis.^[19]

Kinetics of extraction

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (May 2014) (Learn how and when to remove this template message)

It is important to investigate the rate at which the solute is transferred between the two phases, in some cases by an alteration of the contact time it is possible to alter the selectivity of the extraction. For instance, the extraction of palladium or nickel can be very slow because the rate of ligand exchange at these metal centers is much lower than the rates for iron or silver complexes.

Aqueous complexing agents

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (May 2014) (Learn how and when to remove this template message)

If a complexing agent is present in the aqueous phase then it can lower the distribution ratio. For instance, in the case of iodine being distributed between water and an inert organic solvent such as carbon tetrachloride then the presence of iodide in the aqueous phase can alter the extraction chemistry: instead of ${\displaystyle D_{\mathrm {I} ^{+2}}}$ being a constant it becomes

${\displaystyle D_{\mathrm {I} ^{+2}}}$ = k[I₂ (organic)]/[I₂ (aq)][I⁻ (aq)]

This is because the

Industrial process design

In a typical scenario, an industrial process will use an extraction step in which solutes are transferred from the aqueous phase to the organic phase; this is often followed by a scrubbing stage in which unwanted solutes are removed from the organic phase, then a stripping stage in which the wanted solutes are removed from the organic phase. The organic phase may then be treated to make it ready for use again.^[20][21]

After use, the organic phase may be subjected to a cleaning step to remove any degradation products; for instance, in PUREX plants, the used organic phase is washed with sodium carbonate solution to remove any dibutyl hydrogen phosphate or butyl dihydrogen phosphate that might be present.

Liquid-liquid equilibrium calculations

In order to calculate the phase equilibrium, it is necessary to use a thermodynamic model such as NRTL, UNIQUAC, etc. The corresponding parameters of these models can be obtained from literature (e.g. Dechema Chemistry Data Series, Dortmund Data Bank, etc.) or by a correlation process of experimental data.^{[22][23][24][25]}

Equipment

The extraction methods for a range of metals include:[27]^[28]

Cobalt

The extraction of cobalt from

Copper

Copper can be extracted using hydroxyoximes as extractants, a recent paper describes an extractant that has a good selectivity for copper over cobalt and nickel.^[30]

Neodymium

The rare earth element Neodymium is extracted by di(2-ethyl-hexyl)phosphoric acid into hexane by an ion exchange mechanism.^[31]

Nickel

Nickel can be extracted using di(2-ethyl-hexyl)phosphoric acid and tributyl phosphate in a hydrocarbon diluent (Shellsol).^[32]

Palladium and platinum

Dialkyl sulfides, tributyl phosphate and alkyl amines have been used for extracting palladium and platinum.^[33][34]

Polonium

Polonium is produced in reactors from natural ²⁰⁹Bi, bombarded with neutrons, creating ²¹⁰Bi, which then decays to ²¹⁰Po via beta-minus decay. The final purification is done pyrochemically followed by liquid-liquid extraction vs sodium hydroxide at 500 deg C.^[35]

Zinc and cadmium

Zinc and cadmium are both extracted by an ion exchange process, the N,N,N′,N′-tetrakis(2-pyridylmethyl)ethylenediamine (TPEN) acts as a masking agent for the zinc and an extractant for the cadmium.^[36] In the modified Zincex process, zinc is separated from most divalent ions by solvent extraction. D2EHPA (Di (2) ethyl hexyl phosphoric acid) is used for this. A zinc ion replaces the proton from two D2EHPA molecules. To strip the zinc from the D2EHPA, sulfuric acid is used, at a concentration of above 170g/L (typically 240-265g/L).

Lithium

Lithium extraction is more popular due to the high demand of lithium-ion batteries. TBP (Tri-butyl phosphate) and FeCl₃ are mostly used to extract lithium from brine (with high Li/Mg ratio).^[37] Alternatively, Cyanex 272 was also used to extract lithium. The mechanism of lithium extraction was found differently from other metals, such as cobalt, due to the weak coordinating bonding between lithium ions and extractants.^[38]

See also

• Fragrance extraction
• Dortmund Data Bank
• Non-random two-liquid model - (NRTL model) LL Phase Equilibrium Calculation
• UNIQUAC - LL Phase Equilibrium Calculation

References