Thermal energy storage

Most solar thermal power plants use this thermal energy storage concept. The Solana Generating Station in the U.S. can store 6 hours worth of generating capacity in molten salt. During the summer of 2013 the Gemasolar Thermosolar solar power-tower/molten-salt plant in Spain achieved a first by continuously producing electricity 24 hours per day for 36 days.^[19] The Cerro Dominador Solar Thermal Plant, inaugurated in June 2021, has 17.5 hours of heat storage.^[20]

Heat storage in tanks or rock caverns

A steam accumulator consists of an insulated steel pressure tank containing hot water and steam under pressure. As a heat storage device, it is used to mediate heat production by a variable or steady source from a variable demand for heat. Steam accumulators may take on a significance for energy storage in solar thermal energy projects.

Large stores are widely used in Nordic countries to store heat for several days, to decouple heat and power production and to help meet peak demands. Intersessional storage in caverns has been investigated and appears to be economical

Solid or molten silicon offers much higher storage temperatures than salts with consequent greater capacity and efficiency. It is being researched as a possible more energy efficient storage technology. Silicon is able to store more than 1 MWh of energy per cubic meter at 1400 °C. An additional advantage is the relative abundance of silicon when compared to the salts used for the same purpose.^[25][26]

Molten aluminum

Another medium that can store thermal energy is molten (recycled) aluminum. This technology was developed by the Swedish company Azelio. The material is heated to 600 °C. When needed, the energy is transported to a Stirling engine using a heat-transfer fluid.

Heat storage in hot rocks or concrete

Water has one of the highest thermal capacities at 4.2 kJ/(kg⋅K) whereas concrete has about one third of that. On the other hand, concrete can be heated to much higher temperatures (1200 °C) by for example electrical heating and therefore has a much higher overall volumetric capacity. Thus in the example below, an insulated cube of about 2.8 m³ would appear to provide sufficient storage for a single house to meet 50% of heating demand. This could, in principle, be used to store surplus wind or solar heat due to the ability of electrical heating to reach high temperatures. At the neighborhood level, the Wiggenhausen-Süd solar development at Friedrichshafen in southern Germany has received international attention. This features a 12,000 m³ (420,000 cu ft) reinforced concrete thermal store linked to 4,300 m² (46,000 sq ft) of solar collectors, which will supply the 570 houses with around 50% of their heating and hot water. Siemens-Gamesa built a 130 MWh thermal storage near Hamburg with 750 °C in basalt and 1.5 MW electric output.^[27][28] A similar system is scheduled for Sorø, Denmark, with 41–58% of the stored 18 MWh heat returned for the town's district heating, and 30–41% returned as electricity.^[29]

“Brick toaster” is a recently (August 2022) announced innovative heat reservoir operating at up to 1,500 °C (2,732 °F) that its maker, Titan Cement/Rondo claims should be able cut global CO
₂ output by 15% over 15 years.^[30]

Latent heat storage

Because latent heat storage (LHS) is associated with a phase transition, the general term for the associated media is Phase-Change Material (PCM). During these transitions, heat can be added or extracted without affecting the material's temperature, giving it an advantage over SHS-technologies. Storage capacities are often higher as well.

There are a multitude of PCMs available, including but not limited to salts, polymers, gels, paraffin waxes and metal alloys, each with different properties. This allows for a more target-oriented system design. As the process is

PCMs are further subdivided into organic, inorganic and eutectic materials. Compared to organic PCMs, inorganic materials are less flammable, cheaper and more widely available. They also have higher storage capacity and thermal conductivity. Organic PCMs, on the other hand, are less corrosive and not as prone to phase-separation.

Another important factor in LHS is the encapsulation of the PCM. Some materials are more prone to erosion and leakage than others. The system must be carefully designed in order to avoid unnecessary loss of heat.^[10]

Miscibility gap alloy technology

Miscibility gap alloys ^[31] rely on the phase change of a metallic material (see: latent heat) to store thermal energy.^[32]

Rather than pumping the liquid metal between tanks as in a molten-salt system, the metal is encapsulated in another metallic material that it cannot alloy with (immiscible). Depending on the two materials selected (the phase changing material and the encapsulating material) storage densities can be between 0.2 and 2 MJ/L.

A working fluid, typically water or steam, is used to transfer the heat into and out of the system.

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (October 2020) (Learn how and when to remove this template message)

Several applications are being developed where ice is produced during off-peak periods and used for cooling at a later time. For example, air conditioning can be provided more economically by using low-cost electricity at night to freeze water into ice, then using the

In addition to using ice in direct cooling applications, it is also being used in heat pump-based heating systems. In these applications, the phase change energy provides a very significant layer of thermal capacity that is near the bottom range of temperature that water source heat pumps can operate in. This allows the system to ride out the heaviest heating load conditions and extends the timeframe by which the source energy elements can contribute heat back into the system.

Cryogenic energy storage

Thermo-chemical heat storage (TCS) involves some kind of reversible exotherm/endotherm chemical reaction with thermo-chemical materials (TCM). Depending on the reactants, this method can allow for an even higher storage capacity than LHS.

In one type of TCS, heat is applied to decompose certain molecules. The reaction products are then separated, and mixed again when required, resulting in a release of energy. Some examples are the decomposition of potassium oxide (over a range of 300–800 °C, with a heat decomposition of 2.1 MJ/kg), lead oxide (300–350 °C, 0.26 MJ/kg) and calcium hydroxide (above 450 °C, where the reaction rates can be increased by adding zinc or aluminum). The photochemical decomposition of nitrosyl chloride can also be used and, since it needs photons to occur, works especially well when paired with solar energy.^[10]

Adsorption (or Sorption) solar heating and storage

Adsorption processes also fall into this category. It can be used to not only store thermal energy, but also control air humidity.

The low cost ($200/ton) and high cycle rate (2,000×) of synthetic zeolites such as Linde 13X with water adsorbate has garnered much academic and commercial interest recently for use for thermal energy storage (TES), specifically of low-grade solar and waste heat. Several pilot projects have been funded in the EU from 2000 to the present (2020). The basic concept is to store solar thermal energy as chemical latent energy in the zeolite. Typically, hot dry air from flat plate solar collectors is made to flow through a bed of zeolite such that any water adsorbate present is driven off. Storage can be diurnal, weekly, monthly, or even seasonal depending on the volume of the zeolite and the area of the solar thermal panels. When heat is called for during the night, or sunless hours, or winter, humidified air flows through the zeolite. As the humidity is adsorbed by the zeolite, heat is released to the air and subsequently to the building space. This form of TES, with specific use of zeolites, was first taught by Guerra in 1978.^[36] Advantages over molten salts and other high temperature TES include that (1) the temperature required is only the stagnation temperature typical of a solar flat plate thermal collector, and (2) as long as the zeolite is kept dry, the energy is stored indefinitely. Because of the low temperature, and because the energy is stored as latent heat of adsorption, thus eliminating the insulation requirements of a molten salt storage system, costs are significantly lower.

Salt hydrate technology

One example of an experimental storage system based on chemical reaction energy is the salt hydrate technology. The system uses the reaction energy created when salts are hydrated or dehydrated. It works by storing heat in a container containing 50% sodium hydroxide (NaOH) solution. Heat (e.g. from using a solar collector) is stored by evaporating the water in an endothermic reaction. When water is added again, heat is released in an exothermic reaction at 50 °C (120 °F). Current systems operate at 60% efficiency. The system is especially advantageous for seasonal thermal energy storage, because the dried salt can be stored at room temperature for prolonged times, without energy loss. The containers with the dehydrated salt can even be transported to a different location. The system has a higher energy density than heat stored in water and the capacity of the system can be designed to store energy from a few months to years.^[37]

In 2013 the Dutch technology developer TNO presented the results of the MERITS project to store heat in a salt container. The heat, which can be derived from a solar collector on a rooftop, expels the water contained in the salt. When the water is added again, the heat is released, with almost no energy losses. A container with a few cubic meters of salt could store enough of this thermochemical energy to heat a house throughout the winter. In a temperate climate like that of the Netherlands, an average low-energy household requires about 6.7 GJ/winter. To store this energy in water (at a temperature difference of 70 °C), 23 m³ insulated water storage would be needed, exceeding the storage abilities of most households. Using salt hydrate technology with a storage density of about 1 GJ/m³, 4–8 m³ could be sufficient.^[38]

As of 2016, researchers in several countries are conducting experiments to determine the best type of salt, or salt mixture. Low pressure within the container seems favorable for the energy transport.

The DSPEC consists of two components: a molecule and a nanoparticle. The molecule is called a chromophore-catalyst assembly which absorbs sunlight and kick starts the catalyst. This catalyst separates the electrons and the water molecules. The nanoparticles are assembled into a thin layer and a single nanoparticle has many chromophore-catalyst on it. The function of this thin layer of nanoparticles is to transfer away the electrons which are separated from the water. This thin layer of nanoparticles is coated by a layer of titanium dioxide. With this coating, the electrons that come free can be transferred more quickly so that hydrogen could be made. This coating is, again, coated with a protective coating that strengthens the connection between the chromophore-catalyst and the nanoparticle.

Using this method, the solar energy acquired from the solar panels is converted into fuel (hydrogen) without releasing the so-called greenhouse gasses. This fuel can be stored into a fuel cell and, at a later time, used to generate electricity.^[42]

Molecular Solar Thermal System (MOST)

Another promising way to store solar energy for electricity and heat production is a so-called molecular solar thermal system (MOST). With this approach a molecule is converted by photoisomerization into a higher-energy isomer. Photoisomerization is a process in which one (cis trans) isomer is converted into another by light (solar energy). This isomer is capable of storing the solar energy until the energy is released by a heat trigger or catalyst (then, the isomer is converted into its original isomer). A promising candidate for such a MOST is Norbornadiene (NBD). This is because there is a high energy difference between the NBD and the quadricyclane (QC) photoisomer. This energy difference is approximately 96 kJ/mol. It is also known that for such systems, the donor-acceptor substitutions provide an effective means for red shifting the longest-wavelength absorption. This improves the solar spectrum match.

A crucial challenge for a useful MOST system is to acquire a satisfactory high energy storage density (if possible, higher than 300 kJ/kg). Another challenge of a MOST system is that light can be harvested in the visible region. The functionalization of the NBD with the donor and acceptor units is used to adjust this absorption maxima. However, this positive effect on the solar absorption is compensated by a higher molecular weight. This implies a lower energy density. This positive effect on the solar absorption has another downside. Namely, that the energy storage time is lowered when the absorption is redshifted. A possible solution to overcome this anti-correlation between the energy density and the red shifting is to couple one chromophore unit to several photo switches. In this case, it is advantageous to form so called dimers or trimers. The NBD share a common donor and/or acceptor.

Kasper Moth-Poulsen and his team tried to engineer the stability of the high energy photo isomer by having two electronically coupled photo switches with separate barriers for thermal conversion.^[43] By doing so, a blue shift occurred after the first isomerization (NBD-NBD to QC-NBD). This led to a higher energy of isomerization of the second switching event (QC-NBD to QC-QC). Another advantage of this system, by sharing a donor, is that the molecular weight per norbornadiene unit is reduced. This leads to an increase of the energy density.

Eventually, this system could reach a quantum yield of photoconversion up 94% per NBD unit. A quantum yield is a measure of the efficiency of photon emission. With this system the measured energy densities reached up to 559 kJ/kg (exceeding the target of 300 kJ/kg). So, the potential of the molecular photo switches is enormous—not only for solar thermal energy storage but for other applications as well.^[43]

In 2022, researchers reported combining the MOST with a chip-sized thermoelectric generator to generate electricity from it. The system can reportedly store solar energy for up to 18 years and may be an option for renewable energy storage.^[44][45]

Thermal Battery

A thermal energy battery is a physical structure used for the purpose of storing and releasing

Thermal batteries are very common, and include such familiar items as a hot water bottle. Early examples of thermal batteries include stone and mud cook stoves, rocks placed in fires, and kilns. While stoves and kilns are ovens, they are also thermal storage systems that depend on heat being retained for an extended period of time.

Types of thermal batteries

Thermal batteries generally fall into 4 categories with different forms and applications, although fundamentally all are for the storage and retrieval of thermal energy. They also differ in method and density of heat storage.^{[citation needed]}

Phase change thermal battery

Phase change materials used for thermal storage are capable of storing and releasing significant thermal capacity at the temperature that they change phase. These materials are chosen based on specific applications because there is a wide range of temperatures that may be useful in different applications and a wide range of materials that change phase at different temperatures. These materials include salts and waxes that are specifically engineered for the applications they serve. In addition to manufactured materials, water is a phase change material. The latent heat of water is 334 joules/gram. The phase change of water occurs at 0 °C (32 °F).

Some applications use the thermal capacity of water or ice as cold storage; others use it as heat storage. It can serve either application; ice can be melted to store heat then refrozen to warm an environment. The advantage of using a phase change in this way is that a given mass of material can absorb a large quantity of energy without its temperature changing. Hence a thermal battery that uses a phase change can be made lighter, or more energy can be put into it without raising the internal temperature unacceptably.^{[citation needed]}

Encapsulated thermal battery

An encapsulated thermal battery is physically similar to a phase change thermal battery in that it is a confined amount of physical material which is thermally heated or cooled to store or extract energy. However, in a non-phase change encapsulated thermal battery, the temperature of the substance is changed without inducing a phase change. Since a phase change is not needed many more materials are available for use in an encapsulated thermal battery. One of the key properties of an encapsulated thermal battery is its volumetric heat capacity (VHC), also termed volume-specific heat capacity. Typical substances used for these thermal batteries include water, concrete, and wet sand.^{[citation needed]}

An example of an encapsulated thermal battery is a residential water heater with a storage tank.^[46][47] This thermal battery is usually slowly charged over a period of about 30–60 minutes for rapid use when needed (e.g., 10–15 minutes). Many utilities, understanding the "thermal battery" nature of water heaters, have begun using them to absorb excess renewable energy power when available for later use by the homeowner. According to the above-cited article,^[46] "net savings to the electricity system as a whole could be $200 per year per heater – some of which may be passed on to its owner".

Research into using sand as a heat storage medium has been performed in Finland, where a prototype sand battery has been built to store renewable solar and wind power as heat, for later use as district heating, and possible later power generation.^[48]

Ground heat exchange thermal battery

A ground heat exchanger (GHEX) is an area of the earth that is utilized as a seasonal/annual cycle thermal battery. These thermal batteries are areas of the earth into which pipes have been placed in order to transfer thermal energy. Energy is added to the GHEX by running a higher temperature fluid through the pipes and thus raising the temperature of the local earth. Energy can also be taken from the GHEX by running a lower-temperature fluid through those same pipes.

GHEX are usually implemented in two forms. The picture above depicts what is known as a "horizontal" GHEX where trenching is used to place an amount of pipe in a closed loop in the ground. They are also formed by drilling boreholes into the ground, either vertically or horizontally, and then the pipes are inserted in the form of a closed-loop with a "u-bend" fitting on the far end of the loop.

Heat energy can be added to or removed from a GHEX at any point in time. However, they are most often used as a

A good example of the Annual Cycle nature of a GHEX Thermal Battery can be seen in the ASHRAE Building study.[52] As seen there in the 'Ground Loop and Ambient Air temperatures by date' graphic (Figure 2–7), one can easily see the annual cycle sinusoidal shape of the ground temperature as heat is seasonally extracted from the ground in winter and rejected to the ground in summer, creating a ground "thermal charge" in one season that is not uncharged and driven the other direction from neutral until a later season. Other more advanced examples of Ground-based Thermal Batteries utilizing intentional well-bore thermal patterns are currently in research and early use. ^{[citation needed]}

Other thermal batteries

In the defense industry

Storage heaters are commonplace in European homes with time-of-use metering (traditionally using cheaper electricity at nighttime). They consist of high-density ceramic bricks or feolite blocks heated to a high temperature with electricity and may or may not have good insulation and controls to release heat over a number of hours. Some advice not to use them in areas with young children or where there is an increased risk of fires due to poor housekeeping, both due to the high temperatures involved.^[54][55]

With the rise of wind and solar power (and other renewable energies) providing an ever increasing share of energy input into the electricity grids in some countries, the use of larger scale electric energy storage is being explored by several commercial companies. Ideally, the utilisation of surplus renewable energy is transformed into high temperature high grade heat in highly insulated heat stores, for release later when needed. An emerging technology is the use of vacuum super insulated (VSI) heat stores.^[56] The use of electricity to generate heat, and not say direct heat from solar thermal collectors, means that very high temperatures can be realised, potentially allowing for inter seasonal heat transfer—storing high grade heat in summer from surplus photovoltaics generation into heat stored for the following winter with relatively minimal standing losses.

Solar energy storage

Solar energy is an application of thermal energy storage. Most practical solar thermal storage systems provide storage from a few hours to a day's worth of energy. However, a growing number of facilities use seasonal thermal energy storage (STES), enabling solar energy to be stored in summer to heat space during winter.[57]^[58][59] In 2017 Drake Landing Solar Community in Alberta, Canada, achieved a year-round 97% solar heating fraction, a world record made possible by incorporating STES.^[57][60]

The combined use of latent heat and sensible heat are possible with high temperature solar thermal input. Various eutectic metal mixtures, such as aluminum and silicon (AlSi
₁₂) offer a high melting point suited to efficient steam generation,^[61] while high alumina cement-based materials offer good storage capabilities.^[62]

Pumped-heat electricity storage

In pumped-heat electricity storage (PHES), a reversible heat-pump system is used to store energy as a temperature difference between two heat stores.^[63][64][65]

Isentropic

Isentropic systems involve two insulated containers filled, for example, with crushed rock or gravel: a hot vessel storing thermal energy at high temperature/pressure, and a cold vessel storing thermal energy at low temperature/pressure. The vessels are connected at top and bottom by pipes and the whole system is filled with an inert gas such as argon.^[66]

While charging, the system can use off-peak electricity to work as a heat pump. One prototype used argon at ambient temperature and pressure from the top of the cold store is compressed adiabatically, to a pressure of, for example, 12 bar, heating it to around 500 °C (900 °F). The compressed gas is transferred to the top of the hot vessel where it percolates down through the gravel, transferring heat to the rock and cooling to ambient temperature. The cooled, but still pressurized, gas emerging at the bottom of the vessel is then adiabatically expanded to 1 bar, which lowers its temperature to −150 °C. The cold gas is then passed up through the cold vessel where it cools the rock while warming to its initial condition.

The energy is recovered as electricity by reversing the cycle. The hot gas from the hot vessel is expanded to drive a generator and then supplied to the cold store. The cooled gas retrieved from the bottom of the cold store is compressed which heats the gas to ambient temperature. The gas is then transferred to the bottom of the hot vessel to be reheated.

The compression and expansion processes are provided by a specially designed reciprocating machine using sliding valves. Surplus heat generated by inefficiencies in the process is shed to the environment through heat exchangers during the discharging cycle.^[63][66]

The developer claimed that a round trip efficiency of 72–80% was achievable.^[63][66] This compares to >80% achievable with pumped hydro energy storage.^[64]

Another proposed system uses

 Renewable energy portal

References