Waveguide filter

Source: Wikipedia, the free encyclopedia.
by fences of three posts each. The ends of the posts can be seen protruding through the wall of the guide.

A waveguide filter is an

television broadcasting
.

Waveguide filters were

cavities and novel materials such as ceramic resonators
.

A particular feature of waveguide filter design concerns the mode of transmission. Systems based on pairs of conducting wires and similar technologies have only one mode of transmission. In waveguide systems, any number of modes are possible. This can be both a disadvantage, as spurious modes frequently cause problems, and an advantage, as a dual-mode design can be much smaller than the equivalent waveguide single mode design. The chief advantages of waveguide filters over other technologies are their ability to handle high power and their low loss. The chief disadvantages are their bulk and cost when compared with technologies such as microstrip filters.

There is a wide array of different types of waveguide filters. Many of them consist of a chain of coupled resonators of some kind that can be modelled as a

directional couplers, and diplexers
. These devices frequently take on the form of a filter, at least in part.

Scope

The common meaning of waveguide, when the term is used unqualified, is the hollow metal kind (or occasionally

optical fibres. This subject is outside the scope of the article with the exception that dielectric rod resonators are sometimes used inside hollow metal waveguides. Transmission line[o] technologies such as conducting wires and microstrip can be thought of as waveguides,[3]
but are not commonly called such and are also outside the scope of this article.

Basic concepts

Filters

In

Waveguides

Waveguides are metal conduits used to confine and direct radio signals. They are usually made of brass, but aluminium and copper are also used.[5] Most commonly they are rectangular, but other cross-sections such as circular or elliptical are possible. A waveguide filter is a filter composed of waveguide components. It has much the same range of applications as other filter technologies in electronics and radio engineering but is very different mechanically and in principle of operation.[6]

The technology used for constructing filters is chosen to a large extent by the frequency of operation that is expected, although there is a large amount of overlap. Low frequency applications such as

lumped element filters to distinguish them. At still higher frequencies, the microwave bands, the design switches to waveguide filters, or sometimes a combination of waveguides and transmission lines.[7]

Waveguide filters have much more in common with transmission line filters than lumped element filters; they do not contain any discrete capacitors or inductors. However, the waveguide design may frequently be equivalent (or approximately so) to a lumped element design. Indeed, the design of waveguide filters frequently starts from a lumped element design and then converts the elements of that design into waveguide components.[8]

Modes

diagram
Figure 2. The field patterns of some common waveguide modes

One of the most important differences in the operation of waveguide filters compared to transmission line designs concerns the mode of transmission of the

electromagnetic wave carrying the signal. In a transmission line, the wave is associated with electric currents on a pair of conductors. The conductors constrain the currents to be parallel to the line, and consequently both the magnetic and electric components of the electromagnetic field are perpendicular to the direction of travel of the wave. This transverse mode is designated TEM[l] (transverse electromagnetic). On the other hand, there are infinitely many modes that any completely hollow waveguide can support, but the TEM mode is not one of them. Waveguide modes are designated either TE[m] (transverse electric) or TM[n] (transverse magnetic), followed by a pair of suffixes identifying the precise mode.[9]

This multiplicity of modes can cause problems in waveguide filters when spurious modes are generated. Designs are usually based on a single mode and frequently incorporate features to suppress the unwanted modes. On the other hand, advantage can be had from choosing the right mode for the application, and even sometimes making use of more than one mode at once. Where only a single mode is in use, the waveguide can be modelled like a conducting transmission line and results from transmission line theory can be applied.[10]

Cutoff

Another feature peculiar to waveguide filters is that there is a definite frequency, the cutoff frequency, below which no transmission can take place. This means that in theory low-pass filters cannot be made in waveguides. However, designers frequently take a lumped element low-pass filter design and convert it to a waveguide implementation. The filter is consequently low-pass by design and may be considered a low-pass filter for all practical purposes if the cutoff frequency is below any frequency of interest to the application. The waveguide cutoff frequency is a function of transmission mode, so at a given frequency, the waveguide may be usable in some modes but not others. Likewise, the guide wavelength[h]g) and characteristic impedance[b] (Z0) of the guide at a given frequency also depend on mode.[11]

Dominant mode

The mode with the lowest cutoff frequency of all the modes is called the dominant mode. Between cutoff and the next highest mode, this is the only mode it is possible to transmit, which is why it is described as dominant. Any spurious modes generated are rapidly attenuated along the length of the guide and soon disappear. Practical filter designs are frequently made to operate in the dominant mode.[12]

In rectangular waveguide, the TE10[q] mode (shown in figure 2) is the dominant mode. There is a band of frequencies between the dominant mode cutoff and the next highest mode cutoff in which the waveguide can be operated without any possibility of generating spurious modes. The next highest cutoff modes are TE20,[r] at exactly twice the TE10 mode, and TE01[s] which is also twice TE10 if the waveguide used has the commonly used aspect ratio of 2:1. The lowest cutoff TM mode is TM11[t] (shown in figure 2) which is times the dominant mode in 2:1 waveguide. Thus, there is an octave over which the dominant mode is free of spurious modes, although operating too close to cutoff is usually avoided because of phase distortion.[13]

In circular waveguide, the dominant mode is TE11[u] and is shown in figure 2. The next highest mode is TM01.[v] The range over which the dominant mode is guaranteed to be spurious-mode free is less than that in rectangular waveguide; the ratio of highest to lowest frequency is approximately 1.3 in circular waveguide, compared to 2.0 in rectangular guide.[14]

Evanescent modes

Evanescent modes are modes below the cutoff frequency. They cannot propagate down the waveguide for any distance, dying away exponentially. However, they are important in the functioning of certain filter components such as irises and posts, described later, because energy is stored in the evanescent wave fields.[15]

Advantages and disadvantages

Like transmission line filters, waveguide filters always have multiple passbands, replicas of the lumped element prototype. In most designs, only the lowest frequency passband is useful (or lowest two in the case of band-stop filters) and the rest are considered unwanted spurious artefacts. This is an intrinsic property of the technology and cannot be designed out, although design can have some control over the frequency position of the spurious bands. Consequently, in any given filter design, there is an upper frequency beyond which the filter will fail to carry out its function. For this reason, true low-pass and high-pass filters cannot exist in waveguide. At some high frequency there will be a spurious passband or stopband interrupting the intended function of the filter. But, similar to the situation with waveguide cutoff frequency, the filter can be designed so that the edge of the first spurious band is well above any frequency of interest.[16]

The range of frequencies over which waveguide filters are useful is largely determined by the waveguide size needed. At lower frequencies the waveguide needs to be impractically large in order to keep the cutoff frequency below the operational frequency. On the other hand, filters whose operating frequencies are so high that the wavelengths are sub-millimetre cannot be manufactured with normal machine shop processes. At frequencies this high, fibre-optic technology starts to become an option.[17]

Waveguides are a low-loss medium. Losses in waveguides mostly come from

conductivity. An example of such requirements is satellite applications which require low loss, high selectivity, and linear group delay from their filters.[18]

One of the main advantages of waveguide filters over TEM mode technologies is the quality of their

resistance of conductors, especially in wound inductors, limits the Q of TEM resonators. This improved Q leads to better performing filters in waveguides, with greater stop band rejection. The limitation to Q in waveguides comes mostly from the ohmic losses in the walls described earlier, but silver plating the internal walls can more than double Q.[20]

Waveguides have good power handling capability, which leads to filter applications in

printed circuit technology, and when integrated on the same printed board as other circuit blocks they incur little additional cost.[22]

History

Lord Rayleigh
first suggested waveguide transmission.

The idea of a waveguide for electromagnetic waves was first suggested by

Lord Rayleigh in 1897. Rayleigh proposed that a coaxial transmission line could have the centre conductor removed, and waves would still propagate down the inside of the remaining cylindrical conductor despite there no longer being a complete electrical circuit of conductors. He described this in terms of the wave reflecting repeatedly off the internal wall of the outer conductor in a zig-zag fashion as it progressed down the waveguide. Rayleigh was also the first to realise that there was a critical wavelength, the cutoff wavelength, proportional to the cylinder diameter, above which wave propagation is not possible. However, interest in waveguides waned because lower frequencies were more suitable for long-distance radio communication. Rayleigh's results were forgotten for a time and had to be rediscovered by others in the 1930s when interest in microwaves revived. Waveguides were first developed, in a circular form, by George Clark Southworth and J. F. Hargreaves in 1932.[23]

The first

Otto Zobel and others quickly developed this further.[24] Development of distributed element filters began in the years before World War II. A major paper on the subject was published by Mason and Sykes in 1937;[25] a patent[26] filed by Mason in 1927 may contain the first published filter design using distributed elements.[27]

photo
Hans Bethe developed waveguide aperture theory.

Mason and Sykes' work was focused on the formats of coaxial cable and

balanced pairs of wires, but other researchers later applied the principles to waveguides as well. Much development on waveguide filters was carried out during World War II driven by the filtering needs of radar and electronic countermeasures. A good deal of this was at the MIT Radiation Laboratory (Rad Lab), but other laboratories in the US and the UK were also involved such as the Telecommunications Research Establishment in the UK. Amongst the well-known scientists and engineers at Rad Lab were Julian Schwinger, Nathan Marcuvitz, Edward Mills Purcell, and Hans Bethe. Bethe was only at Rad Lab a short time but produced his aperture theory while there. Aperture theory is important for waveguide cavity filters, which were first developed at Rad Lab. Their work was published after the war in 1948 and includes an early description of dual-mode cavities by Fano and Lawson.[28]

Theoretical work following the war included the commensurate line theory of

Chebyshev approximation to determine element values. Cauer's work was largely developed during World War II (Cauer was killed towards the end of it), but could not be widely published until hostilities ended. While Cauer's work concerns lumped elements, it is of some importance to waveguide filters; the Chebyshev filter, a special case of Cauer's synthesis, is widely used as a prototype filter for waveguide designs.[30]

Designs in the 1950s started with a lumped element prototype (a technique still in use today), arriving after various transformations at the desired filter in a waveguide form. At the time, this approach was yielding

Stanford Research Institute published a method for designing filters which started with a distributed element prototype, the stepped impedance prototype. This filter was based on quarter-wave impedance transformers of various widths and was able to produce designs with bandwidths up to an octave (a fractional bandwidth of 2/3). Young's paper specifically addresses directly coupled cavity resonators, but the procedure can equally be applied to other directly coupled resonator types.[31]

drawing
Figure 3. Pierce's waveguide implementation of a cross-coupled filter

The first published account of a

Collins Radio Company.[33]

The initial non-military application of waveguide filters was in the

The need for frequency-independent delay in satellite applications led to more research into the waveguide incarnation of cross-coupled filters. Previously, satellite communications systems used a separate component for

delay equalisation. The additional degrees of freedom obtained from cross-coupled filters held out the possibility of designing a flat delay into a filter without compromising other performance parameters. A component that simultaneously functioned as both filter and equaliser would save valuable weight and space. The needs of satellite communication also drove research into the more exotic resonator modes in the 1970s. Of particular prominence in this respect is the work of E. L. Griffin and F. A. Young, who investigated better modes for the 12-14 GHz band when this began to be used for satellites in the mid-1970s.[35]

Another space-saving innovation was the

dielectric constant to be useful for space saving. This changed with the introduction of ceramic resonators with very low temperature coefficients in the 1970s. The first of these was from Massé and Pucel using barium tetratitanate[note 1] at Raytheon in 1972. Further improvements were reported in 1979 by Bell Labs and Murata Manufacturing. Bell Labs' barium nonatitanate[note 2] resonator had a dielectric constant of 40 and Q of 5000–10,000 at 2-7 GHz. Modern temperature-stable materials have a dielectric constant of about 90 at microwave frequencies, but research is continuing to find materials with both low loss and high permittivity; lower permittivity materials, such as zirconium stannate titanate[note 3] (ZST) with a dielectric constant of 38, are still sometimes used for their low loss property.[36]

An alternative approach to designing smaller waveguide filters was provided by the use of non-propagating evanescent modes. Jaynes and Edson proposed evanescent mode waveguide filters in the late 1950s. Methods for designing these filters were created by Craven and Young in 1966. Since then, evanescent mode waveguide filters have seen successful use where waveguide size or weight are important considerations.[37]

A relatively recent technology being used inside hollow-metal-waveguide filters is finline, a kind of planar dielectric waveguide. Finline was first described by Paul Meier in 1972.[38]

Multiplexer history

photo
John R. Pierce invented the cross-coupled filter and the contiguous passband multiplexer.

Multiplexers were first described by Fano and Lawson in 1948. Pierce was the first to describe multiplexers with contiguous passbands. Multiplexing using directional filters was invented by Seymour Cohn and Frank Coale in the 1950s. Multiplexers with compensating immittance resonators at each junction are largely the work of E. G. Cristal and G. L. Matthaei in the 1960s. This technique is still sometimes used, but the modern availability of computing power has led to the more common use of synthesis techniques which can directly produce matching filters without the need for these additional resonators. In 1965 R. J. Wenzel discovered that filters which were singly terminated,[k] rather than the usual doubly terminated, were complementary—exactly what was needed for a diplexer.[c] Wenzel was inspired by the lectures of circuit theorist Ernst Guillemin.[39]

Multi-channel, multi-octave multiplexers were investigated by Harold Schumacher at Microphase Corporation, and his results were published in 1976. The principle that multiplexer filters may be matched when joined together by modifying the first few elements, thus doing away with the compensating resonators, was discovered accidentally by E. J. Curly around 1968 when he mistuned a diplexer. A formal theory for this was provided by J. D. Rhodes in 1976 and generalised to multiplexers by Rhodes and Ralph Levy in 1979.[40]

From the 1980s, planar technologies, especially microstrip, have tended to replace other technologies used for constructing filters and multiplexers, especially in products aimed at the consumer market. The recent innovation of post-wall waveguide allows waveguide designs to be implemented on a flat substrate with low-cost manufacturing techniques similar to those used for microstrip.[41]

Components

diagram
Figure 4. Ladder circuit implementation of a lumped element low-pass filter

Waveguide filter designs frequently consist of two different components repeated a number of times. Typically, one component is a resonator or discontinuity with a lumped circuit equivalent of an inductor, capacitor, or LC resonant circuit. Often, the filter type will take its name from the style of this component. These components are spaced apart by a second component, a length of guide which acts as an impedance transformer. The impedance transformers have the effect of making alternate instances of the first component appear to be a different impedance. The net result is a lumped element equivalent circuit of a ladder network. Lumped element filters are commonly

ladder topology, and such a circuit is a typical starting point for waveguide filter designs. Figure 4 shows such a ladder. Typically, waveguide components are resonators, and the equivalent circuit would be LC resonators instead of the capacitors and inductors shown, but circuits like figure 4 are still used as prototype filters with the use of a band-pass or band-stop transformation.[42]

Filter performance parameters, such as stopband rejection and rate of transition between passband and stopband, are improved by adding more components and thus increasing the length of the filter. Where the components are repeated identically, the filter is an

image parameter filter design, and performance is enhanced simply by adding more identical elements. This approach is typically used in filter designs which use a large number of closely spaced elements such as the waffle-iron filter. For designs where the elements are more widely spaced, better results can be obtained using a network synthesis filter design, such as the common Chebyshev filter and Butterworth filters. In this approach the circuit elements do not all have the same value, and consequently the components are not all the same dimensions. Furthermore, if the design is enhanced by adding more components then all the element values must be calculated again from scratch. In general, there will be no common values between the two instances of the design. Chebyshev waveguide filters are used where the filtering requirements are rigorous, such as satellite applications.[43][44]

Impedance transformer

An impedance transformer is a device which makes an impedance at its output port appear as a different impedance at its input port. In waveguide, this device is simply a short length of waveguide. Especially useful is the quarter-wave impedance transformer which has a length of λg/4. This device can turn capacitances into inductances and vice versa.[45] It also has the useful property of turning shunt-connected elements into series-connected elements and vice versa. Series-connected elements are otherwise difficult to implement in waveguide.[46]

Reflections and discontinuities

Many waveguide filter components work by introducing a sudden change, a discontinuity, to the transmission properties of the waveguide. Such discontinuities are equivalent to lumped impedance elements placed at that point. This arises in the following way: the discontinuity causes a partial reflection of the transmitted wave back down the guide in the opposite direction, the ratio of the two being known as the reflection coefficient. This is entirely analogous to a reflection on a transmission line where there is an established relationship between reflection coefficient and the impedance that caused the reflection. This impedance must be reactive, that is, it must be a capacitance or an inductance. It cannot be a resistance since no energy has been absorbed—it is all either transmitted onward or reflected. Examples of components with this function include irises, stubs, and posts, all described later in this article under the filter types in which they occur.[47]

Impedance step

An impedance step is an example of a device introducing a discontinuity. It is achieved by a step change in the physical dimensions of the waveguide. This results in a step change in the characteristic impedance of the waveguide. The step can be in either the

H-plane[g] (change of width[i]) of the waveguide.[48]

Resonant cavity filter

Cavity resonator

A basic component of waveguide filters is the cavity resonator. This consists of a short length of waveguide blocked at both ends. Waves trapped inside the resonator are reflected back and forth between the two ends. A given geometry of cavity will resonate at a characteristic frequency. The resonance effect can be used to selectively pass certain frequencies. Their use in a filter structure requires that some of the wave is allowed to pass out of one cavity into another through a coupling structure. However, if the opening in the resonator is kept small then a valid design approach is to design the cavity as if it were completely closed and errors will be minimal. A number of different coupling mechanisms are used in different classes of filter.[49]

The nomenclature for modes in a cavity introduces a third index, for example TE011. The first two indices describe the wave travelling up and down the length of the cavity, that is, they are the transverse mode numbers as for modes in a waveguide. The third index describes the

interference pattern of the forward travelling and reflected waves. The third index is equal to the number of half wavelengths down the length of the guide. The most common modes used are the dominant modes: TE101 in rectangular waveguide, and TE111 in circular waveguide. TE011 circular mode is used where very low loss (hence high Q) is required but cannot be used in a dual-mode filter because it is circularly symmetric. Better modes for rectangular waveguide in dual-mode filters are TE103 and TE105. However, even better is the TE113 circular waveguide mode which can achieve a Q of 16,000 at 12 GHz.[50]

Tuning screw

Tuning screws are screws inserted into resonant cavities which can be adjusted externally to the waveguide. They provide fine tuning of the

thread-locking compound. For screws inserted only a small distance, the equivalent circuit is a shunt capacitor, increasing in value as the screw is inserted. However, when the screw has been inserted a distance λ/4 it resonates equivalent to a series LC circuit. Inserting it further causes the impedance to change from capacitive to inductive, that is, the arithmetic sign changes.[51]

Iris

diagram
Figure 5. Some waveguide iris geometries and their lumped element equivalent circuits

An iris is a thin metal plate across the waveguide with one or more holes in it. It is used to couple together two lengths of waveguide and is a means of introducing a discontinuity. Some of the possible geometries of irises are shown in figure 5. An iris which reduces the width of a rectangular waveguide has an equivalent circuit of a shunt inductance, whereas one which restricts the height is equivalent to a shunt capacitance. An iris which restricts both directions is equivalent to a parallel LC resonant circuit. A series LC circuit can be formed by spacing the conducting portion of the iris away from the walls of the waveguide. Narrowband filters frequently use irises with small holes. These are always inductive regardless of the shape of the hole or its position on the iris. Circular holes are simple to machine, but elongated holes, or holes in the shape of a cross, are advantageous in allowing the selection of a particular mode of coupling.[52]

Irises are a form of discontinuity and work by exciting evanescent higher modes. Vertical edges are parallel to the electric field (E field) and excite TE modes. The stored energy in TE modes is predominately in the magnetic field (H field), and consequently the lumped equivalent of this structure is an inductor. Horizontal edges are parallel to the H field and excite TM modes. In this case the stored energy is predominately in the E field and the lumped equivalent is a capacitor.[53]

It is fairly simple to make irises that are mechanically adjustable. A thin plate of metal can be pushed in and out of a narrow slot in the side of the waveguide. The iris construction is sometimes chosen for this ability to make a variable component.[54]

Iris-coupled filter

diagram
Figure 6. Iris-coupled filter with three irises

An iris-coupled filter consists of a cascade of impedance transformers in the form of waveguide resonant cavities coupled together by irises.[43] In high power applications capacitive irises are avoided. The reduction in height of the waveguide (the direction of the E field) causes the electric field strength across the gap to increase and arcing (or dielectric breakdown if the waveguide is filled with an insulator) will occur at a lower power than it would otherwise.[55]

Post filter

diagram
Figure 7. Post filter with three rows of posts

Posts are conducting bars, usually circular, fixed internally across the height of the waveguide and are another means of introducing a discontinuity. A thin post has an equivalent circuit of a shunt inductor. A row of posts can be viewed as a form of inductive iris.[56]

A post filter consists of several rows of posts across the width of the waveguide which separate the waveguide into resonant cavities as shown in figure 7. Differing numbers of posts can be used in each row to achieve varying values of inductance. An example can be seen in figure 1. The filter operates in the same way as the iris-coupled filter but differs in the method of construction.[57]

Post-wall waveguide

A post-wall waveguide, or substrate integrated waveguide, is a more recent format that seeks to combine the advantages of low radiation loss, high Q, and high power handling of traditional hollow metal pipe waveguide with the small size and ease of manufacture of planar technologies (such as the widely used microstrip format). It consists of an insulated substrate pierced with two rows of conducting posts which stand in for the side walls of the waveguide. The top and bottom of the substrate are covered with conducting sheets making this a similar construction to the

low temperature co-fired ceramic can be used to make post-wall waveguide circuits. This format naturally lends itself to waveguide post filter designs.[58]

Dual-mode filter

A dual-mode filter is a kind of resonant cavity filter, but in this case each cavity is used to provide two resonators by employing two modes (two polarizations), so halving the volume of the filter for a given order. This improvement in size of the filter is a major advantage in aircraft avionics and space applications. High quality filters in these applications can require many cavities which occupy significant space.[59]

Dielectric resonator filter

diagram
Figure 8. Dielectric resonator filter with three transverse resonators

Dielectric resonators are pieces of dielectric material inserted into the waveguide. They are usually cylindrical since these can be made without machining but other shapes have been used. They can be made with a hole through the centre which is used to secure them to the waveguide. There is no field at the centre when the TE011 circular mode is used so the hole has no adverse effect. The resonators can be mounted coaxial to the waveguide, but usually they are mounted transversally across the width as shown in figure 8. The latter arrangement allows the resonators to be tuned by inserting a screw through the wall of the waveguide into the centre hole of the resonator.[60]

When dielectric resonators are made from a high

thermal conductivity.[61]

The resonators can be coupled together with irises or impedance transformers. Alternatively, they can be placed in a stub-like side-housing and coupled through a small aperture.[62]

Insert filter

diagram
Figure 9. Insert filter with six dielectric resonators in the E-plane.

In insert filters one or more metal sheets are placed longitudinally down the length of the waveguide as shown in figure 9. These sheets have holes punched in them to form resonators. The air dielectric gives these resonators a high Q. Several parallel inserts may be used in the same length of waveguide. More compact resonators may be achieved with a thin sheet of dielectric material and printed metallisation instead of holes in metal sheets at the cost of a lower resonator Q.[63]

Finline filter

Finline is a different kind of waveguide technology in which waves in a thin strip of dielectric are constrained by two strips of metallisation. There are a number of possible topological arrangements of the dielectric and metal strips. Finline is a variation of slot-waveguide but in the case of finline the whole structure is enclosed in a metal shield. This has the advantage that, like hollow metal waveguide, no power is lost by radiation. Finline filters can be made by printing a metallisation pattern on to a sheet of dielectric material and then inserting the sheet into the E-plane of a hollow metal waveguide much as is done with insert filters. The metal waveguide forms the shield for the finline waveguide. Resonators are formed by metallising a pattern on to the dielectric sheet. More complex patterns than the simple insert filter of figure 9 are easily achieved because the designer does not have to consider the effect on mechanical support of removing metal. This complexity does not add to the manufacturing costs since the number of processes needed does not change when more elements are added to the design. Finline designs are less sensitive to manufacturing tolerances than insert filters and have wide bandwidths.[64]

Evanescent-mode filter

It is possible to design filters that operate internally entirely in evanescent modes. This has space saving advantages because the filter waveguide, which often forms the housing of the filter, does not need to be large enough to support propagation of the dominant mode. Typically, an evanescent mode filter consists of a length of waveguide smaller than the waveguide feeding the input and output ports. In some designs this may be folded to achieve a more compact filter. Tuning screws are inserted at specific intervals along the waveguide producing equivalent lumped capacitances at those points. In more recent designs the screws are replaced with dielectric inserts. These capacitors resonate with the preceding length of evanescent mode waveguide which has the equivalent circuit of an inductor, thus producing a filtering action. Energy from many different evanescent modes is stored in the field around each of these capacitive discontinuities. However, the design is such that only the dominant mode reaches the output port; the other modes decay much more rapidly between the capacitors.[65]

Corrugated-waveguide filter

diagram
Figure 10. Corrugated waveguide filter with cutaway showing the corrugations inside
diagram
Figure 11. Longitudinal section through a corrugated waveguide filter

Corrugated-waveguide filters, also called ridged-waveguide filters, consist of a number of ridges, or teeth, that periodically reduce the internal height of the waveguide as shown in figures 10 and 11. They are used in applications which simultaneously require a wide passband, good passband matching, and a wide stopband. They are essentially low-pass designs (above the usual limitation of the cutoff frequency), unlike most other forms which are usually band-pass. The distance between teeth is much smaller than the typical λ/4 distance between elements of other filter designs. Typically, they are designed by the image parameter method with all ridges identical, but other classes of filter such as Chebyshev can be achieved in exchange for complexity of manufacture. In the image design method the equivalent circuit of the ridges is modelled as a cascade of LC half sections. The filter operates in the dominant TE10 mode, but spurious modes can be a problem when they are present. In particular, there is little stopband attenuation of TE20 and TE30 modes.[66]

Waffle-iron filter

The waffle-iron filter is a variant of the corrugated-waveguide filter. It has similar properties to that filter with the additional advantage that spurious TE20 and TE30 modes are suppressed. In the waffle-iron filter, channels are cut through the ridges longitudinally down the filter. This leaves a matrix of teeth protruding internally from the top and bottom surfaces of the waveguide. This pattern of teeth resembles a waffle iron, hence the name of the filter.[67]

Waveguide stub filter

diagram
Figure 12. Waveguide stub filter consisting of three stub resonators

A stub is a short length of waveguide connected to some point in the filter at one end and short-circuited at the other end. Open-circuited stubs are also theoretically possible, but an implementation in waveguide is not practical because electromagnetic energy would be emitted from the open end of the stub, resulting in high losses. Stubs are a kind of resonator, and the lumped element equivalent is an LC resonant circuit. However, over a narrow band, stubs can be viewed as an impedance transformer. The short-circuit is transformed into either an inductance or a capacitance depending on the stub length.[68]

A waveguide stub filter is made by placing one or more stubs along the length of a waveguide, usually λg/4 apart, as shown in figure 12. The ends of the stubs are blanked off to short-circuit them.[69] When the short-circuited stubs are λg/4 long the filter will be a band-stop filter and the stubs will have a lumped-element approximate equivalent circuit of parallel resonant circuits connected in series with the line. When the stubs are λg/2 long, the filter will be a band-pass filter. In this case the lumped-element equivalent is series LC resonant circuits in series with the line.[70]

Absorption filter

Absorption filters dissipate the energy in unwanted frequencies internally as heat. This is in contrast to a conventional filter design where the unwanted frequencies are reflected back from the input port of the filter. Such filters are used where it is undesirable for power to be sent back towards the source. This is the case with high power transmitters where returning power can be high enough to damage the transmitter. An absorption filter may be used to remove transmitter spurious emissions such as harmonics or spurious sidebands. A design that has been in use for some time has slots cut in the walls of the feed waveguide at regular intervals. This design is known as a leaky-wave filter. Each slot is connected to a smaller gauge waveguide which is too small to support propagation of frequencies in the wanted band. Thus those frequencies are unaffected by the filter. Higher frequencies in the unwanted band, however, readily propagate along the side guides which are terminated with a matched load where the power is absorbed. These loads are usually a wedge shaped piece of microwave absorbent material.[71] Another, more compact, design of absorption filter uses resonators with a lossy dielectric.[72]

Filter-like devices

There are many applications of filters whose design objectives are something other than rejection or passing of certain frequencies. Frequently, a simple device that is intended to work over only a narrow band or just one spot frequency will not look much like a filter design. However, a

negative-resistance amplifiers, and time-delay networks.[73]

Impedance matching

photo
Figure 13. An orthomode transducer (a variety of duplexer) incorporating stepped impedance matching

A simple method of impedance matching is

stub matching with a single stub. However, a single stub will only produce a perfect match at one particular frequency. This technique is therefore only suitable for narrow band applications. To widen the bandwidth multiple stubs may be used, and the structure then takes on the form of a stub filter. The design proceeds as if it were a filter except that a different parameter is optimised. In a frequency filter typically the parameter optimised is stopband rejection, passband attenuation, steepness of transition, or some compromise between these. In a matching network the parameter optimised is the impedance match. The function of the device does not require a restriction of bandwidth, but the designer is nevertheless forced to choose a bandwidth because of the structure of the device.[74]

Stubs are not the only format of filter than can be used. In principle, any filter structure could be applied to impedance matching, but some will result in more practical designs than others. A frequent format used for impedance matching in waveguide is the stepped impedance filter. An example can be seen in the duplexer[e] pictured in figure 13.[75]

Directional couplers and power combiners

drawing
Figure 14. A multi-hole waveguide coupler

Directional couplers, power splitters, and power combiners are all essentially the same type of device, at least when implemented with passive components. A directional coupler splits a small amount of power from the main line to a third port. A more strongly coupled, but otherwise identical, device may be called a power splitter. One that couples exactly half the power to the third port (a 3 dB coupler) is the maximum coupling achievable without reversing the functions of the ports. Many designs of power splitter can be used in reverse, whereupon they become power combiners.[76]

A simple form of directional coupler is two parallel transmission lines coupled together over a λ/4 length. This design is limited because the

Bethe-hole directional coupler in which two parallel waveguides are stacked on top of each other and a hole provided for coupling. To produce a wideband design, multiple holes are used along the guides as shown in figure 14 and a filter design applied.[78] It is not only the coupled-line design that suffers from being narrow band, all simple designs of waveguide coupler depend on frequency in some way. For instance the rat-race coupler (which can be implemented directly in waveguide) works on a completely different principle but still relies on certain lengths being exact in terms of λ.[79]

Diplexers and duplexers

A diplexer is a device used to combine two signals occupying different frequency bands into a single signal. This is usually to enable two signals to be transmitted simultaneously on the same communications channel, or to allow transmitting on one frequency while receiving on another. (This specific use of a diplexer is called a duplexer.) The same device can be used to separate the signals again at the far end of the channel. The need for filtering to separate the signals while receiving is fairly self-evident but it is also required even when combining two transmitted signals. Without filtering, some of the power from source A will be sent towards source B instead of the combined output. This will have the detrimental effects of losing a portion of the input power and loading source A with the output impedance of source B thus causing mismatch. These problems could be overcome with the use of a 3 dB directional coupler, but as explained in the previous section, a wideband design requires a filter design for directional couplers as well.[80]

Two widely spaced narrowband signals can be diplexed by joining together the outputs of two appropriate band-pass filters. Steps need to be taken to prevent the filters from coupling to each other when they are at resonance which would cause degradation of their performance. This can be achieved by appropriate spacing. For instance, if the filters are of the iris-coupled type then the iris nearest to the filter junction of filter A is placed λgb/4 from the junction where λgb is the guide wavelength in the passband of filter B. Likewise, the nearest iris of filter B is placed λga/4 from the junction. This works because when filter A is at resonance, filter B is in its stopband and only loosely coupled and vice versa. An alternative arrangement is to have each filter joined to a main waveguide at separate junctions. A decoupling resonator is placed λg/4 from the junction of each filter. This can be in the form of a short-circuited stub tuned to the resonant frequency of that filter. This arrangement can be extended to multiplexers with any number of bands.[81]

For diplexers dealing with contiguous passbands proper account of the

crossover characteristics of filters needs to be considered in the design. An especially common case of this is where the diplexer is used to split the entire spectrum into low and high bands. Here a low-pass and a high-pass filter are used instead of band-pass filters. The synthesis techniques used here can equally be applied to narrowband multiplexers and largely remove the need for decoupling resonators.[82]

Directional filters

diagram
Figure 15. A waveguide directional filter cut away to show the circular waveguide irises

A directional filter is a device that combines the functions of a directional coupler and a diplexer. As it is based on a directional coupler it is essentially a four-port device, but like directional couplers, port 4 is commonly permanently terminated internally. Power entering port 1 exits port 3 after being subject to some filtering function (usually band-pass). The remaining power exits port 2, and since no power is absorbed or reflected this will be the exact complement of the filtering function at port 2, in this case band-stop. In reverse, power entering ports 2 and 3 is combined at port 1, but now the power from the signals rejected by the filter is absorbed in the load at port 4. Figure 15 shows one possible waveguide implementation of a directional filter. Two rectangular waveguides operating in the dominant TE10 mode provide the four ports. These are joined together by a circular waveguide operating in the circular TE11 mode. The circular waveguide contains an iris coupled filter with as many irises as needed to produce the required filter response.[83]

Glossary

^ aperture
An opening in a wall of a waveguide or barrier between sections of waveguide through which electromagnetic radiation can propagate.
^ a b characteristic impedance
Characteristic impedance, symbol Z0, of a waveguide for a particular mode is defined as the ratio of the transverse electric field to the transverse magnetic field of a wave travelling in one direction down the guide. The characteristic impedance for air filled waveguide is given by,
where Zf is the impedance of free space, approximately 377 Ω, λg is the guide wavelength, and λ is the wavelength when unrestricted by the guide. For a dielectric filled waveguide, the expression must be divided by κ, where κ is the dielectric constant of the material, and λ replaced by the unrestricted wavelength in the dielectric medium. In some treatments what is called characteristic impedance here is called the wave impedance, and characteristic impedance is defined as proportional to it by some constant.[84]
^ c d e diplexer, duplexer
A diplexer combines or separates two signals occupying different passbands. A duplexer combines or splits two signals travelling in opposite directions, or of differing polarizations (which may also be in different passbands as well).
^ E-plane
The E-plane is the plane lying in the direction of the transverse electric field, that is, vertically along the guide.[85]
^ guide wavelength
Guide wavelength, symbol λg, is the wavelength measured longitudinally down the waveguide. For a given frequency, λg depends on the mode of transmission and is always longer than the wavelength of an electromagnetic wave of the same frequency in free space. λg is related to the cutoff frequency, fc, by,
where λ is the wavelength the wave would have if unrestricted by the guide. For guides that are filled only with air, this will be the same, for all practical purposes, as the free space wavelength for the transmitted frequency, f.[86]
^ H-plane
The H-plane is the plane lying in the direction of the transverse magnetic field (H being the analysis symbol for
magnetic field strength), that is, horizontally along the guide.[85]
^ i j height, width
Of a rectangular guide, these refer respectively to the small and large internal dimensions of its cross-section. The polarization of the E-field of the dominant mode is parallel to the height.
^ iris
A conducting plate fitted transversally across the waveguide with a, usually large, aperture.
^ singly terminated, doubly terminated
A doubly terminated filter (the normal case) is one where the generator and load, connected to the input and output ports respectively, have impedances matching the filter characteristic impedance. A singly terminated filter has a matching load, but is driven either by a low impedance voltage source or a high impedance current source.[87]
^ TEM mode
Transverse electromagnetic mode, a transmission mode where all the electric field and all the magnetic field are perpendicular to the direction of travel of the electromagnetic wave. This is the usual mode of transmission in pairs of conductors.[88]
^ TE mode
Transverse electric mode, one of a number of modes in which all the electric field, but not all the magnetic field, is perpendicular to the direction of travel of the electromagnetic wave. They are designated H modes in some sources because these modes have a longitudinal magnetic component. The first index indicates the number of half wavelengths of field across the width of the waveguide, and the second index indicates the number of half wavelengths across the height. Properly, the indices should be separated with a comma, but usually they are run together, as mode numbers in double figures rarely need to be considered. Some modes specifically mentioned in this article are listed below. All modes are for rectangular waveguide unless otherwise stated.[89]
          ^ TE01 mode
A mode with one half-wave of electric field across the height of the guide and uniform electric field (zero half-waves) across the width of the guide.
          ^ TE10 mode
A mode with one half-wave of electric field across the width of the guide and uniform electric field across the height of the guide.
          ^ TE20 mode
A mode with two half-waves of electric field across the width of the guide and uniform electric field across the height of the guide.
          ^ TE11 circular mode
A mode with one full-wave of electric field around the circumference of the guide and one half-wave of electric field along a radius.
^ TM mode
Transverse magnetic mode, one of a number of modes in which all the magnetic field, but not all the electric field, is perpendicular to the direction of travel of the electromagnetic wave. They are designated E modes in some sources because these modes have a longitudinal electric component. See TE mode for a description of the meaning of the indices. Some modes specifically mentioned in this article are:
          ^ TM11 mode
A mode with one half-wave of magnetic field across the width of the guide and one half-wave of magnetic field across the height of the guide. This is the lowest TM mode, since TMm0 modes cannot exist.[90]
          ^ TM01 circular mode
A mode with uniform magnetic field around the circumference of the guide and one half-wave of magnetic field along a radius.
^ o p transmission line
A transmission line is a signal transmission medium consisting of a pair of electrical conductors separated from each other, or one conductor and a common return path. In some treatments waveguides are considered to be within the class of transmission lines, with which they have much in common. In this article waveguides are not included so that the two types of medium can more easily be distinguished and referred.

Notes

  1. ^ Barium tetratitanate, BaTi4O9 (Young et al., page 655)
  2. ^ Barium nonatitanate, Ba2Ti9O20 (Nalwa, page 443)
  3. ^ Zirconium stannate titanate, Zr1−xSnxTiO4 (Gusmano et al., page 690)

References

  1. ^ Gibilisco & Sclater, page 913
  2. ^ Yeh & Shimabukuro, page 1
  3. ^ Russer, pages 131–132
  4. ^ Belov et al., page 147
  5. ^ Connor, page 52
  6. ^
    • Hunter, page 201
    • Matthaei et al., page 243
  7. ^
    • Hitchcock & Patterson, page 263
    • Bagad, pages 1.3–1.4
  8. ^ Matthaei et al., page 83
  9. ^
    • Connor, pages 52–53
    • Hunter, pages 201, 203
    • Matthaei et al., page 197
  10. ^
    • Hunter, pages 255–260
    • Matthaei et al., page 197
  11. ^
    • Hunter, pages 201–202
    • Matthaei et al., page 197
  12. ^
    • Elmore & Heald, page 289
    • Mahmoud, pages 32–33
  13. ^
    • Hunter, page 209,
    • Matthaei et al., page 198
  14. ^ Matthaei et al., pages 198, 201
  15. ^ Das & Das, page 112
  16. ^
    • Lee, page 789
    • Matthaei et al., page 541
    • Sorrentino & Bianchi, page 262
  17. ^
    • Hunter, page 201
    • Eskelinen & Eskelinen, page 269
    • Middleton & Van Valkenburg, pages 30.26–30.28
  18. ^
    • Belov et al., page 147
    • Connor, pages 6, 64
    • Hunter, page 230
    • Matthaei et al., page 243
  19. ^
    • Sorrentino & Bianchi, page 691
    • Hunter, page 201
  20. ^ Hunter, pages 201, 230
  21. ^
    • Belov et al., page 147
    • Bowen, page 114
  22. ^
    • Das & Das, page 310
    • Waterhouse, page 8
  23. ^ Sarkar et al., pages 90, 129, 545–546
  24. ^ Bray, page 62
  25. ^
    • Levy & Cohn, page 1055
    • See also Mason & Sykes (1937)
  26. ^ Mason, Warren P., "Wave filter", U.S. patent 1,781,469, filed: 25 June 1927, issued: 11 November 1930.
  27. ^ Millman et al., page 108
  28. ^
    • Levy & Cohn, pages 1055, 1057
    • See also Fano and Lawson (1948)
  29. ^
    • Levy and Cohn, pages 1056–1057
    • See also Richards (1948)
  30. ^
    • Cauer et al., pages 3, 5
    • Mansour, page 166
  31. ^
    • Levy & Cohn, page 1056
    • See also Young (1963)
  32. ^
    • Pierce, J. R., "Guided wave frequency range transducer", U.S. patent 2,626,990, filed: 4 May 1948, issued: 27 January 1953.
    • See also Pierce (1949)
  33. ^ Levy & Cohn, pages 1060–1061
  34. ^
    • Hunter, page 230
    • Huurdeman, pages 369–371
  35. ^
    • Levy & Cohn, pages 1061–1062
    • See also Griffin & Young (1978)
  36. ^
    • Levy & Cohn, pages 1062–1063
    • Nalwa, pages 525–526
    • See also:
      Maasé & Pucel (1972)
    • Cohn (1965)
  37. ^ Zhang, Wang, Li, and Lui (2008)
  38. ^
    • Srivastava &Gupta, page 82
    • See also: Meier (1972)
  39. ^
    • Levy & Cohn, page 1065
    • See also:
      Fano & Lawson (1948)
    • Pierce (1949)
    • Cristal & Matthaei (1964)
    • Wenzel (1969)
  40. ^
    • Levy & Cohn, pages 1064–1065
    • See also:
      Schumacher (1976)
    • Rhodes (1976)
    • Rhodes & Levy (1979)
  41. ^
    • Levy & Cohn, page 1065
    • Xuan & Kishk, page 1
  42. ^ Matthaei et al., pages 427–440
  43. ^ a b Hunter, page 230
  44. ^ Matthaei et al., pages 83–84
  45. ^ Matthaei et al., pages 144–145
  46. ^ Matthaei et al., pages 595–596
  47. ^ Montgomery et al., page 162
  48. ^ Das & Das, pages 134–135
  49. ^
    • Hunter, pages 209–210
    • Matthaei et al., page 243
  50. ^
    • Connor, pages 100–101
    • Levy & Cohn, page 1062
  51. ^ Montgomery et al., pages 168–169
  52. ^
    • Bagad, pages 3.41–3.44
    • Matthaei et al., pages 232–242
    • Montgomery et al., pages 162–179
  53. ^ Montgomery et al., pages 162–179
  54. ^ Bagad, page 3.41
  55. ^ Montgomery et al., page 167
  56. ^
    • Bagad, pages 3.41–3.44
    • Hunter, pages 220–222
    • Matthaei et al., pages 453–454
  57. ^
    • Hunter, pages 220–228
    • Matthaei et al., page 540
  58. ^ Xuan & Kishk, pages 1–2
  59. ^ Hunter, pages 255–260
  60. ^
    • Nalwa, page 525
    • Jarry & Beneat, page 10
  61. ^
    • Nalwa, pages 525–526
    • Jarry & Beneat, page 10
  62. ^
    • Nalwa, pages 525–526
    • Jarry & Beneat, pages 10–12
  63. ^ Jarry & Beneat, page 12
  64. ^
    • Jarry & Beneat, page 12
    • Srivastava & Gupta, pages 82–84
  65. ^
    • Jarry & Beneat, pages 3–5
    • Golio, page 9.9
  66. ^ Matthaei et al., pages 380–390
  67. ^ Matthaei et al., pages 390–409
  68. ^
    • Connor, pages 32–34
    • Radmanesh, pages 295–296
  69. ^ Ke Wu et al., page 612
  70. ^ Matthaei et al., pages 595–596, 726
  71. ^ Cristal, pages 182–183
  72. ^ Minakova & Rud, page 1
  73. ^ Matthaei et al., pages 1–13
  74. ^
    • Connor, pages 32–34
    • Matthaei et al., page 701
  75. ^
    • Das & Das, pages 131–136
    • Matthaei et al., Chapter 6 (pages 255–354)
  76. ^ Lee, page 193, 201
  77. ^ Matthaei et al., page 776
  78. ^ Ishii, pages 205–206, 212,213
  79. ^ Bagad, page 4.6
  80. ^ Maloratsky, pages 165–166
  81. ^ Matthaei et al., pages 969–973
  82. ^
    • Levy & Cohn, page 1065
    • Matthaei et al., pages 991–992
  83. ^ Matthaei et al., pages 843–847
  84. ^
    • Connor, page 7
    • Matthaei et al., pages 197–198
    • Montgomery et al., page 162
  85. ^ a b Meredith, page 127
  86. ^ Connor, page 56
  87. ^ Matthaei et al., page 104
  88. ^
    • Connor, page 2
    • Silver, pages 203–204
  89. ^ Connor, pages 52–54
  90. ^ Connor, page 60

Bibliography