Lithium ion manganese oxide battery

Edit links
Source: Wikipedia, the free encyclopedia.

A lithium ion manganese oxide battery (LMO) is a

LiCoO
2. Cathodes based on manganese-oxide components are earth-abundant, inexpensive, non-toxic, and provide better thermal stability.[1]

Compounds

Spinel LiMn
2O
4

One of the more studied manganese oxide-based cathodes is LiMn
2O
4, a cation ordered member of the spinel structural family (space group Fd3m). In addition to containing inexpensive materials, the three-dimensional structure of LiMn
2O
4 lends itself to high rate capability by providing a well connected framework for the insertion and de-insertion of Li+
 ions during discharge and charge of the battery. In particular, the Li+
 ions occupy the tetrahedral sites within the Mn
2O
4 polyhedral frameworks adjacent to empty octahedral sites.[2][3] As a consequence of this structural arrangement, batteries based on LiMn
2O
4 cathodes have demonstrated a higher rate-capability compared to materials with two-dimensional frameworks for Li+
 diffusion.[4]

A significant disadvantage of cathodes based on LiMn
2O
4 is the surface degradation observed when the average oxidation state of the manganese drops below Mn+3.5. At this concentration, the formally Mn(III) at the surface can disproportionate to form Mn(IV) and Mn(II) by the Hunter mechanism.[5] The Mn(II) formed is soluble in most electrolytes and its dissolution degrades the cathode. With this in mind many manganese cathodes are substituted or doped to keep the average manganese oxidation state above +3.5 during battery use or they will suffer from lower overall capacities as a function of cycle life and temperature.[6]

Layered Li
2MnO
3

Li
2MnO
3 is a lithium rich layered rocksalt structure that is made of alternating layers of lithium ions and lithium and manganese ions in a 1:2 ratio, similar to the layered structure of LiCoO
2. In the nomenclature of layered compounds it can be written Li(Li0.33Mn0.67)O2.[7] Although Li
2MnO
3 is electrochemically inactive, it can be charged to a high potential (4.5 V v.s Li0) in order to undergo lithiation/de-lithiation or delithiated using an acid leaching process followed by mild heat treatment.[8][9] However, extracting lithium from Li
2MnO
3 at such a high potential can also be charge compensated by loss of oxygen from the electrode surface which leads to poor cycling stability.[10] New allotropes of Li
2MnO
3 have been discovered which have better structural stability against oxygen release (longer cycle-life).[11]

Layered LiMnO
2

The layered manganese oxide LiMnO
2 is constructed from corrugated layers of manganese/oxide octahedra and is electrochemically unstable. The distortions and deviation from truly planar metal oxide layers are a manifestation of the electronic configuration of the Mn(III)

Jahn-Teller ion.[12] A layered variant, isostructural with LiCoO2, was prepared in 1996 by ion exchange from the layered compound NaMnO2,[13]
however long term cycling and the defect nature of the charged compound led to structural degradation and cation equilibration to other phases.

Layered Li
2MnO
2

The layered manganese oxide Li
2MnO
2 is structurally related to Li
2MnO
3 and LiCoO2 with similar transition metal oxide layers separated by a layer containing two lithium cations occupying the available two tetrahedral sites in the lattice rather the one octahedral site. The material is typically made by low voltage lithiation of the parent compound, direct lithiation using liquid ammonia, or via use of an organic lithiating reagent.[14] Stability on cycling has been demonstrated in symmetric cells although due to Mn(II) formation and dissolution cycling degradation is expected. Stabilization of the structure using dopants and substitutions to decrease the amount of reduced manganese cations has been a successful route to extending the cycle life of these lithium rich reduced phases. These layered manganese oxide layers are so rich in lithium.

x Li
2MnO
3 • y Li
1+aMn
2-aO
4 • z LiMnO2 composites

One of the main research efforts in the field of lithium-manganese oxide electrodes for lithium-ion batteries involves developing composite electrodes using structurally integrated layered Li
2MnO
3, layered LiMnO2, and spinel LiMn
2O
4, with a chemical formula of x Li
2MnO
3 • y Li
1+aMn
2-aO
4 • z LiMnO2, where x+y+z=1. The combination of these structures provides increased structural stability during electrochemical cycling while achieving higher capacity and rate-capability. A rechargeable capacity in excess of 250 mAh/g was reported in 2005 using this material, which has nearly twice the capacity of current commercialized rechargeable batteries of the same dimensions.[15][16]

See also

References

  1. ISSN 0079-6786
    .
  2. ISSN 0025-5408
    .
  3. S2CID 97239759
    .
  4. ISSN 0013-4651
    .
  5. ISSN 0022-4596
    .
  6. ISSN 0013-4651
    .
  7. ISSN 1364-5501
    .
  8. ISSN 0378-7753
    .
  9. ISSN 1364-5501
    .
  10. ISSN 0897-4756
    .
  11. ISSN 2050-7496
    .
  12. ISSN 0013-4651
    .
  13. S2CID 4330960
    .
  14. ISSN 1388-2481
    .
  15. ISSN 1388-2481
    .
  16. ^ C. S. Johnson, J. T. Vaughey, M. M. Thackeray, T. E. Bofinger, and S. A. Hackney "Layered Lithium-Manganese Oxide Electrodes Derived from Rock-Salt LixMnyOz (x+y=z) Precursors" 194th Meeting of the Electrochemical Society, Boston, MA, Nov. 1–6, (1998)
Retrieved from "https://en.wikipedia.org/w/index.php?title=Lithium_ion_manganese_oxide_battery&oldid=1210312536"