Hydrological model
A hydrologic model is a simplification of a real-world system (e.g., surface water, soil water, wetland, groundwater, estuary) that aids in understanding, predicting, and managing water resources. Both the flow and quality of water are commonly studied using hydrologic models.
Analog models
Prior to the advent of computer models, hydrologic modeling used
Two general categories of analog models are common; scale analogs that use miniaturized versions of the physical system and process analogs that use comparable physics (e.g., electricity, heat, diffusion) to mimic the system of interest.
Scale analogs
Scale models offer a useful approximation of physical or chemical processes at a size that allows for greater ease of visualization.[1] The model may be created in one (core, column), two (plan, profile), or three dimensions, and can be designed to represent a variety of specific initial and boundary conditions as needed to answer a question.
Scale models commonly use physical properties that are similar to their natural counterparts (e.g., gravity, temperature). Yet, maintaining some properties at their natural values can lead to erroneous predictions.[2] Properties such as viscosity, friction, and surface area must be adjusted to maintain appropriate flow and transport behavior. This usually involves matching dimensionless ratios (e.g., Reynolds number, Froude number).
Groundwater flow can be visualized using a scale model built of acrylic and filled with sand, silt, and clay.[3] Water and tracer dye may be pumped through this system to represent the flow of the simulated groundwater. Some physical aquifer models are between two and three dimensions, with simplified boundary conditions simulated using pumps and barriers.[4]
Process analogs
Process analogs are used in hydrology to represent fluid flow using the similarity between
An early process analog model was an electrical network model of an aquifer composed of resistors in a grid.[6] Voltages were assigned along the outer boundary, and then measured within the domain. Electrical conductivity paper[7] can also be used instead of resistors.
Statistical models
Moments
Statistical
The frequency of extremal events, such as severe droughts and storms, often requires the use of distributions that focus on the tail of the distribution, rather than the data nearest the mean. These techniques, collectively known as
Correlation analysis
The degree and nature of correlation may be quantified, by using a method such as the Pearson correlation coefficient, autocorrelation, or the T-test.[19] The degree of randomness or uncertainty in the model may also be estimated using stochastics,[20] or residual analysis.[21] These techniques may be used in the identification of flood dynamics,[22][23] storm characterization,[24][25] and groundwater flow in karst systems.[26]
Regression analysis is used in hydrology to determine whether a relationship may exist between independent and dependent variables. Bivariate diagrams are the most commonly used statistical regression model in the physical sciences, but there are a variety of models available from simplistic to complex.[27] In a bivariate diagram, a linear or higher-order model may be fitted to the data.
Factor Analysis and Principal Component Analysis are multivariate statistical procedures used to identify relationships between hydrologic variables.[28][29]
Convolution is a mathematical operation on two different functions to produce a third function. With respect to hydrologic modeling, convolution can be used to analyze stream discharge's relationship to precipitation. Convolution is used to predict discharge downstream after a precipitation event. This type of model would be considered a “lag convolution”, because of the predicting of the “lag time” as water moves through the watershed using this method of modeling.
Markov Chains are a mathematical technique for determine the probability of a state or event based on a previous state or event.[31] The event must be dependent, such as rainy weather. Markov Chains were first used to model rainfall event length in days in 1976,[32] and continues to be used for flood risk assessment and dam management.
Data-driven models
Data-driven models in hydrology emerged as an alternative approach to traditional statistical models, offering a more flexible and adaptable methodology for analysing and predicting various aspects of hydrological processes. While statistical models rely on rigorous assumptions about probability distributions, data-driven models leverage techniques from artificial intelligence, machine learning, and statistical analysis, including correlation analysis, time series analysis, and statistical moments, to learn complex patterns and dependencies from historical data. This allows them to make more accurate predictions and provide insights into the underlying processes.[33]
Since their inception in the latter half of the 20th century, data-driven models have gained popularity in the water domain, as they help improve forecasting, decision-making, and management of water resources. A couple of notable publications that use data-driven models in hydrology include "Application of machine learning techniques for rainfall-runoff modelling" by Solomatine and Siek (2004),[34] and "Data-driven modelling approaches for hydrological forecasting and prediction" by Valipour et al. (2021).[35] These models are commonly used for predicting rainfall, runoff, groundwater levels, and water quality, and have proven to be valuable tools for optimizing water resource management strategies.
Conceptual models
Conceptual models are commonly used to represent the important components (e.g., features, events, and processes) that relate hydrologic inputs to outputs.[37] These components describe the important functions of the system of interest, and are often constructed using entities (stores of water) and relationships between these entitites (flows or fluxes between stores). The conceptual model is coupled with scenarios to describe specific events (either input or outcome scenarios).
For example, a watershed model could be represented using
Model scope and complexity is dependent on modeling objectives, with greater detail required if human or environmental systems are subject to greater risk. Systems modeling can be used for building conceptual models that are then populated using mathematical relationships.
Example 1
The linear-reservoir model (or Nash Model) is widely used for rainfall-runoff analysis. The model uses a cascade of linear reservoirs along with a constant first-order storage coefficient, K, to predict the outflow from each reservoir (which is then used as the input to the next in the series).
The model combines continuity and storage-discharge equations, which yields an ordinary differential equation that describes outflow from each reservoir. The continuity equation for tank models is:
which indicates that the change in storage over time is the difference between inflows and outflows. The storage-discharge relationship is:
where K is a constant that indicates how quickly the reservoir drains; a smaller value indicates more rapid outflow. Combining these two equation yields
and has the solution:
Example 2
Instead of using a series of linear reservoirs, also the model of a non-linear reservoir can be used.[39]
In such a model the constant K in the above equation, that may also be called reaction factor, needs to be replaced by another symbol, say α (Alpha), to indicate the dependence of this factor on storage (S) and discharge (q).
In the left figure the relation is quadratic:
- α = 0.0123 q2 + 0.138 q - 0.112
Governing equations
Governing equations are used to mathematically define the behavior of the system. Algebraic equations are likely often used for simple systems, while ordinary and partial differential equations are often used for problems that change in space in time. Examples of governing equations include:
Darcy's Law describes steady, one-dimensional groundwater flow using the hydraulic conductivity and the hydraulic gradient:
Groundwater flow equation describes time-varying, multidimensional groundwater flow using the aquifer transmissivity and storativity:
Advection-Dispersion equation describes solute movement in steady, one-dimensional flow using the solute dispersion coefficient and the groundwater velocity:
Poiseuille's Law describes laminar, steady, one-dimensional fluid flow using the shear stress:
Cauchy's integral is an integral method for solving boundary value problems:
Solution algorithms
Analytic methods
Exact solutions for algebraic, differential, and integral equations can often be found using specified boundary conditions and simplifying assumptions. Laplace and Fourier transform methods are widely used to find analytic solutions to differential and integral equations.
Numeric methods
Many real-world mathematical models are too complex to meet the simplifying assumptions required for an analytic solution. In these cases, the modeler develops a numerical solution that approximates the exact solution. Solution techniques include the finite-difference and finite-element methods, among many others.
Specialized software may also be used to solve sets of equations using a graphical user interface and complex code, such that the solutions are obtained relatively rapidly and the program may be operated by a layperson or an end user without a deep knowledge of the system. There are model software packages for hundreds of hydrologic purposes, such as surface water flow, nutrient transport and fate, and groundwater flow.
Commonly used numerical models include SWAT, MODFLOW, FEFLOW, MIKE SHE, and WEAP.
Model calibration and evaluation
Physical models use
Model evaluation is used to determine the ability of the calibrated model to meet the needs of the modeler. A commonly used measure of hydrologic model fit is the Nash-Sutcliffe efficiency coefficient.
See also
References
- ISSN 1607-7938.
- .
- ^ Humphrey, M.D., 1992. Experimental design of physical aquifer models for evaluation of groundwater remediation strategies (Doctoral dissertation).
- S2CID 129919508.
- ^ Principles of Soil and Plant Water Relations https://books.google.com/books?isbn=0124200788
- ^ "Archived copy". Archived from the original on 2015-12-29. Retrieved 2017-05-01.
{{cite web}}
: CS1 maint: archived copy as title (link) - ^ "Conductive Paper and Pen: PASCO".
- ^ Beard, Leo R. Statistical methods in hydrology. HYDROLOGIC ENGINEERING CENTER DAVIS CA, 1962.
- ISSN 1944-7973.
- .
- Yevjevich, Vujica. Probability and statistics in hydrology. Fort Collins, CO: Water resources publications, 1972.
- ^ Zaharia, L. "L-MOMENTS AND THEIR USE IN MAXIMUM DISCHARGES'ANALYSIS IN CURVATURE CARPATHIANS REGION." Aerul si Apa. Componente ale Mediului (2013): 119.
- ISBN 9783319433158.
- S2CID 14783093.
- S2CID 122128745.
- ISSN 1099-1085.
- .
- ^ https://water.usgs.gov/osw/bulletin17b/dl_flow.pdf[bare URL PDF]
- ^ Helsel, Dennis R., and Robert M. Hirsch. Statistical methods in water resources. Vol. 49. Elsevier, 1992
- ISSN 1944-7973.
- ISSN 1944-7973.
- .
- .
- .
- ISSN 1944-7973.
- .
- OCLC 1422999.
- ISSN 1944-7973.
- .
- ^ Salas, Jose D. Applied modeling of hydrologic time series. Water Resources Publication, 1980.
- ^ "Markov Chains explained visually". Explained Visually. Retrieved 2017-04-21.
- ISSN 1944-7973.
- ^ Abrahart, R. P., See, L. M., & Solomatine, D. P. (2008). Practical Hydroinformatics: Computational Intelligence and Technological Developments in Water Applications. Springer.
- ^ Solomatine, D. P., & Siek, M. B. (2004). Application of machine learning techniques for rainfall-runoff modeling. Hydroinformatics: A wide range of technologies, 333-342.
- ^ Valipour, M., Shahsavani, D., & Choubin, B. (2021). Data-driven modeling approaches for hydrological forecasting and prediction. Journal of Hydrology, 597, 125996.
- ISBN 978-0-415-46532-8.
- S2CID 135032550.
- ^ a b Non-linear reservoir model for rainfall-runoff relations
- ^ Rainfall-runoff modelling using a non-linear reservoir
- ISSN 2073-4441.
- ISSN 2214-5818.
- S2CID 129781883.
- S2CID 213914582.
- ISSN 1099-1085.