Talk:Katana/Draft

Page contents not supported in other languages.
Source: Wikipedia, the free encyclopedia.
For other uses, see Talk:Katana/Draft (disambiguation).
Diagram showing the parts of a katana

Katana (刀) is the word for "

loan word by the English language
; as Japanese does not have separate plural and singular forms, both "katanas" and "katana" are considered acceptable plural forms in English.

The katana was typically paired with the wakizashi or shōtō, a similarly made but shorter sword, both worn by the members of the warrior class. It could also be worn with the tantō, an even smaller similarly shaped blade. The two weapons together were called the daishō, and represented the social power and personal honor of the samurai. The long blade was used for open combat, while the shorter blade was considered a side arm, designed more for close quarters combat.

The katana was primarily used for cutting, but can be used as stabbing weapon and intended for use with a two-handed grip. It is traditionally worn edge up in the obi (belt). While the practical arts for using the sword for its original purpose are now obsolete,

iaidō
.

Authentic Japanese swords are fairly uncommon today, although genuine antiques can be acquired. Prices vary depending on the smith, the condition and the polish of the blade. Well made blades by well known smiths in "art polish" can easily sell for hundreds of thousands of dollars. More common swords by lesser smiths can be purchased in shirasaya (holding scabbard) for under $2000. Modern katana and wakizashi are only made by the few licenced practitioners that still practice making these crafted weapons today.

History of the Japanese sword

Early history

One of the oldest known Japanese forms of sword dates from the

700 AD
, along with the folded steel process. In reality the folded steel process and single edge swords had been brought over from China or Korea through trade. Between 987 – 1597, swords are kotō: these are considered the pinnacle of Japanese swordcraft. Early models had uneven curves with the deepest part of the curve at the hilt. As eras changed the center of the curve tended to move up the blade.

By the

twelfth century, civil war erupted, and the vast need for swords together with the ferocity of the fighting caused the highly artistic techniques of the Kamakura period (known as the Golden Age of Swordmaking) to be abandoned in favor of more utilitarian and disposable weapons. The export of katana reached its height during Muromachi period, when at least 200,000 katana were shipped to the Ming dynasty
in official trade in an attempt to soak up the production of Japanese weapons and make it harder for pirates in the area to arm. The Mongol invasions of Japan in the thirteenth century spurred further evolution of the Japanese Sword. Often forced to abandon traditional mounted archery for hand-to-hand combat, many samurai found that their swords were too delicate and prone to damage when used against the thick leather armor of the invaders. In response, Japanese swordsmiths started to adopt thinner and simpler temper lines. Certain Japanese swordsmiths of this period began to make blades with thicker backs and bigger points as a response to the Mongol threat.[1]

The craft decayed as time progressed and firearms were introduced as a decisive force on the battlefield.

New swords

In times of peace, swordsmiths returned to the making of refined and artistic blades, and the beginning of the

Momoyama period
saw the return of high quality creations. As the techniques of the ancient smiths had been lost during the previous period of war, these swords were called shintō, literally "new swords." These are considered inferior to most kotō, and generally coincide with a degradation in manufacturing skills. As the Edo period progressed, blade quality declined, though ornamentation was refined. The addition of engravings known as horimono was originally for religious reasons, and these were simple and tasteful. In the more complex work found on many shintō, form no longer strictly followed function.

Under the

Tokugawa Shogunate, swordmaking declined along with the use of firearms.[2]
The master swordsmith Munetsugu published opinions that the arts and techniques of the shinto swords were inferior to the kotō blades, and that research should be made by all swordsmiths to rediscover the lost techniques. Munetsugu travelled the land teaching what he knew to all who would listen, and swordsmiths rallied to his cause and ushered in a second renaissance in Japanese sword smithing. With the discarding of the shintō style, and the re-introduction of old and rediscovered techniques, swords made in the kotō style between 1761 – 1876 are shinshintō, "new revival swords" or literally 'new-new swords.' These are considered superior to most shintō, but worse than true kotō.

The arrival of

Haitorei edict in 1876 all but banned carrying swords and guns on streets. Overnight, the market for swords died, many swordsmiths were left without a trade to pursue, and valuable skills were lost. Katana remained in use in some occupations such as the police force. At the same time, kendo
was incorporated into police training so that police officers would have at the training necessary to properly use one.

"Type 95" Non Commissioned Officer's sword of the Second World War; made to resemble a Commissioned Officer's shin guntō, they were made of standard machine steel, with an embossed and painted metal handle designed to look like a traditional tsuka.

In time, the need to arm soldiers with swords was perceived again and over the decades at the beginning of the 20th century swordsmiths again found work. These swords, called shin-gunto (gunto meaning Military Sword), NCO shin-gunto or Kai-gunto. Shin-gunto blades had very large differences in their quality. Most, of the blades found in shin-gunto mounts are are machine made blades, often oil quenched and of poor quality steel. NCO shin-gunto were typically the worst quality, with metal tsuka (hilts), by the end of the war, metal supplies had gotten so limited simple wooden tsukas were used. No NCO shin-gunto were traditionally made, and they are often serialized. There where also some blades made during World War 2 were handmade but not by traditional methods, these blades are called Hantanzo, Mantetsuto, Muratato, Showato or Yotetsuto.

There were swords made during this period that were made using traditional methods; these are termed Gendaito or Kindaito. These blades were typically stamped on their nakago (tangs) if they were made using non-traditional methods or materials. There are possible exceptions, with those bearing star (Jumei Tosho) stamps, however the experts are still not in full agreement.

The terms gunto, gendaito and showato are often used improperly and can easily cause confusion. The literal translation of each term is quite different from the collectors usage. For example, gunto translates to Military sword and this refers to all swords in military mounts, not to whether the blade is handmade or not. However in common usage, gunto has fallen to mass produced, non-traditionally made blades having no or little artistic value. Gendaito, the literally translated means a modern sword made (either traditionally or not) between 1876 and 1945. To collectors, gendaito has come to mean traditionally made blades of that time period which have folded steel and are water quenched.

The craft of making swords was kept alive through the efforts of a few individuals, notably Gassan Sadakazu and Gassan Sadakatsu who were employed as Imperial artisans. These smiths produced fine works that stand with the best of the older blades for the Emperor and other high ranking officials. The students of Gassan Sadakatsu went on to be designated Intangible Cultural Assets, "Living National Treasures," as they embodied knowledge that was considered to be fundamentally important to the Japanese identity.

Recent history and modern use

Under the United States occupation at the end of

General Douglas MacArthur, Dr. Homma produced blades from the various periods of Japanese history and MacArthur was able to identify very quickly what blades held artistic merit and which could be considered purely weapons. As a result of this meeting, the ban was amended so that guntō weapons would be destroyed while swords of artistic merit could be owned and preserved. Even so, many katana were sold to American soldiers at a bargain price; as of 1958 there were more Japanese swords in America than in Japan. The vast majority of these 1,000,000 or more swords were guntō, but there were still a sizable number of older swords.[3]

Swordsmiths had been increasingly turning to producing civilian goods after the Edo period but this disarmament and subsequent regulations almost put an end to the production of katana. A few smiths did continue their trade, and Dr. Homma went on to be a founding figure of the Nihon Bijitsu Hozon Token Kai, the Society for the Preservation of Art Swords, who made it their mission to preserve the old techniques and blades. With the efforts of other like-minded individuals, the katana avoided disappearing and many swordsmiths have continued the work begun by Munetsugu, re-discovering old swordmaking techniques in the process.

Modern katana manufactured according to traditional methods are usually known as

iaito training swords. Some replica katana have been used in modern-day armed robberies.[4]

Classification of Japanese swords

Several katana and wakizashi blades, illustrating the variations in length and curvature. The nakago are well visible.

What generally differentiates the different swords is their length. Japanese swords are measured in units of shaku, a shaku being around 30cm or one foot). A blade shorter than 1 shaku is considered a tantō (knife). A blade longer than 1 shaku but less than 2 is considered a shōtō (short sword). The wakizashi and kodachi are in this category.

A blade longer than 2 shaku is considered a daitō, or long sword. Before 1500 most swords were worn suspended from cords on a belt, blade-down. This style is called jindachi-zukuri, and daitō worn in this fashion are called tachi (average blade length of 75 cm). From 1500 – 1867, almost all swords were worn through an obi, paired with a smaller blade. Both blades were blade-up. This style is called buke-zukuri, and all daitō worn in this fashion are katana, averaging 65 cm in blade length.

A

chiisakatana
is simply a shorter katana. It is longer than the wakizashi, lying between one and two shaku in length. The most common reference to a chiisakatana is a shorter katana that does not have a companion blade. They were most commonly made in the buke-zukuri mounting.

Abnormally long blades (longer than 3 shaku), usually carried across the back, are called

nodachi
. The word ōdachi is also sometimes used as a synonym for katana.

Since 1867, restrictions and/or the deconstruction of the samurai class meant that most blades have been worn jindachi-zukuri style, like Western navy officers. Recently (since 1953) there has been a resurgence in the buke-zukuri style, permitted only for demonstration purposes. Swords designed specifically to be tachi are generally kotō rather than shintō, so they are generally better manufactured and more elaborately decorated. However, these are still katana if worn in modern buke-zukuri style.

Japanese swords can be traced back to one of five provinces, each of which had its own school, traditions and 'trademarks' - e.g., the swords from Mino province were "from the start famous for their sharpness". These schools are known as Gokaden (The Five Traditions).[5] These traditions and provinces are as follows:

  • Sōshū School, known for mokume hada and midareba hamon in nei deki
  • Yamato School, known for masame hada and suguha hamon in nei deki
  • Bizen School, known for mokume hada and midareba hamon in noi deki
  • Yamashiro School, known for mokume hada and suguha hamon in nei deki
  • Mino School, known for hard mokume hada and midareba mixed with togari-ba

In the Koto era there were several other schools that did not fit within the Gokaden or were known to mix elements of each Gokaden, and they were called wakimono (small school). There were 19 commonly referenced wakimono.

Manufacturing

Main article:
katana construction
Blacksmith Munechika (end of the 10th century), helped by a fox spirit, forging the blade ko-kitsune-maru ("Little fox"). The kami is represented by a woman surrounded by foxes. Engraving by Ogata Gekko (1859-1920), 1873.

Katana and wakizashi were often forged with different profiles, different blade thicknesses, and varying amounts of grind. Wakizashi were not simply scaled-down katana; they were often forged in hira-zukuri or other such forms which were very rare on katana.

The daishō was not always forged together. If a samurai was able to afford a daishō, it was often composed of whichever two swords could be conveniently acquired, sometimes by different smiths and in different styles. Even when a daishō contained a pair of blades by the same smith, they were not always forged as a pair or mounted as one. Daishō made as a pair, mounted as a pair, and owned/worn as a pair, are therefore uncommon and considered highly valuable, especially if they still retain their original mountings (as opposed to later mountings, even if the later mounts are made as a pair).

Forging

Engraving of the Edo era depicting forge scenes.

The forging of a Japanese blade typically took hours or days, and was considered a sacred art.[6] As with many complex endeavors, rather than a single craftsman, several artists were involved. There was a smith to forge the rough shape, often a second smith (apprentice) to fold the metal, a specialist polisher, and even a specialist for the edge itself. Often, there were sheath, hilt, and tsuba specialists as well.

The most famous part of the manufacturing process was the folding of the steel. Japanese swords and other edged weapons are manufactured by the Chinese method of repeatedly heating, folding and hammering the metal. This practice became popular due to the use of highly impure metals, stemming from the low temperature yielded in the smelting at that time and place. The folding did several things:

  • It eliminated any bubbles in the metal.
  • It homogenized the metal, spreading the elements (such as carbon) evenly throughout - increasing the effective strength by decreasing the number of potential weak points.
  • It burned off many impurities, helping to overcome the poor quality of the raw Japanese steel.
  • It created layers, by continuously decarburizing the surface and bringing it into the blade's interior, which gives the swords their hada (grain)(for comparison see pattern welding).

Contrary to popular belief, continued folding will not create a "super-strong" blade; once impurities are burnt off and the carbon content homogenized, further folding offers little benefit and will gradually burn out the carbon, leading eventually to a softer steel less able to hold an edge. More than about a dozen folds are uncommon and swords never have more than two dozen folds. A blade folded 12 times will have more than 4,000 'layers' underneath the initial blade to begin with. Even before this point, more layers does not equal a better sword; an even and clean composition is obtained early in the folding process, and control of carbon content has a much greater effect on the blade's functionality. Thus, the best results were usually obtained at 8-10 folds.[citation needed]

One of the core philosophies of the Japanese sword is that it has a single edge (called the ha). This means that the rear of the sword (the mune) can be used to reinforce the edge, and the Japanese took full advantage of this. Steel’s exact flex and strength vary dramatically with heat variation. If steel cools quickly, from a hot temperature, it becomes martensite, which is very hard but brittle. Slower, from a lower temperature, and it becomes pearlite, which has significantly more flex but does not hold an edge. When finished, the steel is not quenched or tempered in the conventional European fashion. To control the cooling, the sword is heated and painted with layers of sticky paste, made up of clay, charcoal powder and sandstone dust. A thin layer on the edge of the sword ensures quick cooling for a hard edge, with a thicker layer of mud on the rest of the blade causing slower cooling and softer, more flexible steel to give the blade the required flex. When the application is finished, the sword is quenched and hardens correctly. This process also makes the edge of the blade contract less than the back when cooling down, something that aids the smith in establishing the curvature of the blade. The patern and thickness of the coating determines what the harmon will look like after the blade is hardened (yaki-ire). It is important to note, while this process is often refered to as tempering, it is not. Yaki-ire is actually heat-treating.

Decoration

Almost all blades are decorated, although not all blades are decorated on the visible part of the blade. Once the blade is cool, and the mud is scraped off, the blade has designs and grooves cut into it. Some other engravings on the blade are aesthetic: signatures and dedications written in kanji and engravings depicting gods, dragons, or other acceptable beings, called horimono. Some are more practical. The presence of a hi ("blood groove" or

I beam
, lessening the weight of the sword yet keeping structural integrity and strength. Furthermore the hi (always done on both sides of the blade) make a whistling sound when the sword is swung (the tachikaze). If the swordsman hears one whistle when swinging a grooved katana then that means that just one groove is making the whistle. Two whistles means that both the edge of the blade and a groove are making a whistle, and three whistles together (the blade edge and both grooves) would tell the swordsman that his blade is perfectly angled with the direction of the cut.

Following the addition of horimono or hi, the nakago (tang) is finished with a file, which leave marks behind called yasuri-me. The nakago is not cleaned or polished, in fact doing this can cut the value of the sword considerably. The purpose is to show how well the blade steel ages and help determine the province of the blade. There are approximately 12 easily recognized yasuri-me, typically called by their slant direction.

Once the smith completed the yasuri-me, the sword was then sent out for finishing, typically to other artisians. This included togi (polishing/shaping), fitting to a

koshirae (mountings), such as the menuki
(decorative grip swells), fuchi and kashira (handle collar and cap), kozuka (small utility knife handle), kogai (decorative skewer-like implement), saya lacquer, and tsuka-ito (the silk thread or cord used to wrap the tsuka), received similar levels of artistry.

Once the blade was complete, it was sent back to the smith and if the smith approved of the quality of the blade and its fittings he would enscribe his name, date the blade was made and place the smith lived on the nakago of the sword. This etching was known as a mei. Not all smiths added a mei to the blade (some smiths thought the sword alone spoke of who made it), some added only a name, some added information as requested by the customer. There are some instances of mei's being forged by other smiths to increase the prices they could charge for the blade. One legend revolves around two smiths, one of which went running over to anothers shop only to kick and punch the other smith. When the other smith asked why he would do this the smith in question replied "I heard you carving the mei, and I know your name doesn't have as many strokes as you used, thus you could only be using my name".

Use

The tachi became the primary weapon on the battlefield during Kamakura period, used by cavalry mounted samurai. The sword was mostly considered as a secondary weapon until then, used in the battlefield only after the bow and spear were no longer feasible. During the Edo period samurai went about on foot unarmored, and with much less combat being fought on horseback in open battlefields the need for an effective close quarter weapon resulted in samurai being armed with daisho.

Testing of swords, called tameshigiri, was practiced on a variety of materials to test the sword's sharpness and practice cutting technique. This included prisoners, dead and sometimes even alive. Several swords have had the data from these tests cuts painted, typically in gold paint, on the nakago of the blade.

Kenjutsu is the use of the Japanese sword in combat. The katana was primarily a cutting weapon, or more specifically, a slicing one. However, the katana's moderate curve allows for effective thrusting as well. The hilt of the katana was usually held with two hands, though a fair amount of one-handed techniques exist. The placement of the right hand was dictated by both the length of the tsuka and the length of the wielder's arm.

For cutting, there was a specific technique called 'ten uchi.' Ten uchi refers to an organized motion made by arms and wrist, during a descending strike. As the sword is swung downwards, the elbow joint drastically extends at the last instant, popping the sword into place. This motion causes the swordsman's grip to twist slightly and if done correctly, is said to feel like wringing a towel. This motion itself caused the katana's blade to impact its target with sharp force, and is used to break initial resistance. From there, fluidly continuing along the motion wrought by 'ten uchi,' the arms would follow through with the stroke, dragging the sword through its target. Because the katana slices rather than chops, it is this 'dragging' which allows it to do maximum damage, and is thusly incorporated into the cutting technique. At full speed, the swing will appear to be full stroke, the katana passing through the targeted object. The segments of the swing are hardly visible, if at all. Assuming that the target is, for example, a human torso -- ten uchi will break the initial resistance supplied by shoulder muscles and the clavical. The follow through would continue the slicing motion, through whatever else it would encounter, until the blade inherently exited the body, due a combination of the motion and its curved shape.

Nearly all styles of kenjutsu share the same five basic guard stances. They are as follows; chudan no kamae (middle guard), jodan no kamae (high guard), gedan no kamae (low guard) hasso (side guard), and waki no gamae (rear guard).

The katana's razor-edge was so hard that upon hitting an equally hard or harder object, such as another sword's ha (edge), chipping became a definite risk. As such, blocking an oncoming blow blade-to-blade was generally avoided. In fact, evasive body maneuvers were preferred over blade contact by most, but, if such was not done, the shinogi (side) or the mune (back of the blade) was used for defense in many styles, rather than the precious edge. A popular method for defeating descending slashes was to simply beat the sword aside. In some instances, an umbrella block — positioning the blade overhead, diagonally (point towards the ground, pommel towards the sky) - would create an effective shield against a descending strike. If the angle of the block was drastic enough, the curve of the katana's spine would cause the attacker's blade to slide along its counter and off to the side.[7]

Comparisons with swords of other cultures

The Japanese sword has been praised widely for its sharpness and effect on the battlefield, but its reputation as a superior weapon has led to the exaggeration of its actual capabilities in popular culture.

Traditional Japanese steel is called tamahagane, and as it is never fully melted during production it is relatively heterogeneous but more labor-intensive to work than European steel. Weapons such as swords from Toledo, Spain could be produced in large quantities at a low cost with a moderate sacrifice in quality because of the greater availability of iron in Europe. Because Japan was an iron-poor society, making a sword was an inherently expensive undertaking, and so the majority of swords made were of high quality.

The differences between the katana and other swords are due less to the limitations of their makers than to the requirements of their use. Katana are capable of damaging Japanese armor to varying degrees: Older Koto era swords were designed when armor was prevalent and were generally thicker and more curved; consequently they had relatively good armor penetration, although weapons such as the

mail. Strong thrusts, however, could split the links of mail and penetrate effectively. Plate armour was commonly defeated by half-swording
, gripping the blade with one or both hands, and thrusting at unprotected areas.

Many sword types from the very beginning of the history of the sword, through the medieval period and the renaissance to the 20th century, were designed for the same combat modes as Japanese ones, fighting against lightly-armored or unarmored men on foot. Styles that relied on a single longsword for both offense and defense were well known outside of Japan as well, as documented in numerous fencing treatises such as Joachim Meyer's Fechtbuch,[8] and disparities in weight have been greatly exaggerated; both katanas and other longswords weighed between 1.0 and 1.5 kg (2-3 pounds).

The majority of the swords of other cultures were of a moderate hardness throughout the blade as opposed to the variable hardness of the katana. A harder edge generally stays sharp longer and will cut a harder target, but is more prone to chipping, while a softer edge loses its sharpness and becomes gouged more easily, but is more resistant to fractures.

See also

Some famous katana smiths

Famous historic katana users

References

  1. ISBN 4-7700-2071-6
    .
  2. ^ Perrin, Noel. Giving Up the Gun: Japan's Reversion to the Sword, 1543-1879. Boston: David R. Godine, 1979.
  3. ^ John Yumoto, The Japanese Sword, a handbook, Tuttle Publishing, 1958
  4. ^ "Sword Robbers Strike Third Shop". IC Coventry.
  5. ISBN 4-7700-2071-6
    .
  6. ^ Irvine, Gregory. The Japanese Sword: The Soul of the Samurai. London: V&A Publications, 2000.
  7. ^ Irvine, Gregory. The Japanese Sword: The Soul of the Samurai. London: V&A Publications, 2000.
  8. ^ http://www.schielhau.org/Meyer.title.html

Further reading

  • Irvine, Gregory. The Japanese Sword: The Soul of the Samurai. London: V&A Publications, 2000.
  • Kapp, Leon. The Craft of the Japanese Sword. Kodansha Intl. Ltd., 1987.
  • Perrin, Noel. Giving Up the Gun: Japan's Reversion to the Sword, 1543-1879. Boston: David R. Godine, 1979.
  • Robinson, H. Russell. Japanese Arms and Armor. New York: Crown Publishers Inc., 1969.
  • Sinclaire, Clive. Samurai: The Weapons and Spirit of the Japanese Warrior
  • Yumoto, John M. The Samurai Sword: A Handbook. Boston: Tuttle Publishing, 1958.

External links

Wikimedia Commons has media related to katana.

Gallery

  • Handle of a katana of the 19th century given to an ambassador.
    Handle of a katana of the 19th century given to an ambassador.
  • Nakago of a wakizashi blade.
    Nakago of a wakizashi blade.
  • Kissaki of a tachi blade, Bizen school, signed Kuni Osafune Yoshigake; Nambokucho era (14th century).
    Kissaki of a tachi blade, Bizen school, signed Kuni Osafune Yoshigake; Nambokucho era (14th century).
  • The habaki which locks the blade is visible just under the tsuba (guard).
    The
    tsuba
     (guard).
  • An Edo era wakizashi. The tsukamaki (handle lacing) is off, showing the shark skin. Note the decoration of the saya.
    An Edo era wakizashi. The tsukamaki (handle lacing) is off, showing the shark skin. Note the decoration of the saya.
  • Elaborated tsuba of the Edo era.
    Elaborated
    tsuba
     of the Edo era.
  • Wooden scabbard, shirasaya, used to protect the blade when not worn for some time.
    Wooden scabbard,
    shirasaya
    ,     used to protect the blade when not worn for some time.

[[Category:Japanese swords]] [[Category:Japanese terms]] [[Category:Medieval weapons]] {{Link FA|de}} {{Link FA|zh}} [[bg:Катана]] [[ca:Katana]] [[cs:Katana]] [[da:Katana]] [[de:Katana]] [[es:Katana]] [[fa:کتانا]] [[fr:Katana]] [[ko:가타나]] [[hr:Katana]] [[it:Katana]] [[he:קטאנה]] [[la:catana]] [[lt:Katana]] [[ms:Katana]] [[nl:Katana]] [[ja:日本刀]] [[no:Katana]] [[pl:Katana]] [[pt:Katana]] [[ru:Катана]] [[sl:Katana]] [[sr:Катана]] [[fi:Katana]] [[sv:Katana]] [[tr:Katana]] [[vi:Gươm Nhật]] [[zh:日本刀]]

Retrieved from "https://en.wikipedia.org/w/index.php?title=Talk:Katana/Draft&oldid=983504429"