Active suspension

An active suspension is a type of

Skyhook theory is that the ideal suspension would let the vehicle maintain a stable posture, unaffected by weight transfer or road surface irregularities, as if suspended from an imaginary hook in the sky continuing at a constant altitude above sea level, therefore remaining stable.

Since an actual skyhook is obviously impractical,

A vehicle contacts the ground through the spring and damper in a normal spring damper suspension, as in Figure 1. To achieve the same level of stability as the Skyhook theory, the vehicle must contact the ground through the spring, and the imaginary line with the damper, as in Figure 2. Theoretically, in a case where the damping coefficient reaches an infinite value, the vehicle will be in a state where it is completely fixed to the imaginary line, thus the vehicle will not shake.

Active

Active suspensions, the first to be introduced, use separate actuators which can exert an independent force on the suspension to improve the riding characteristics. The drawbacks of this design are high cost, added complication and mass of the apparatus, and the need for frequent maintenance on some implementations. Maintenance can require specialised tools, and some problems can be difficult to diagnose.

Hydraulic actuation

Hydraulically actuated suspensions are controlled with the use of hydraulics. The first example appeared in 1954, with the hydropneumatic suspension developed by Paul Magès at Citroën. The hydraulic pressure is supplied by a high pressure radial piston hydraulic pump. Sensors continually monitor body movement and vehicle ride level, constantly supplying the hydraulic height correctors with new data. In a matter of a few milliseconds, the suspension generates counter forces to raise or lower the body. During driving maneuvers, the encased nitrogen compresses instantly, offering six times the compressibility of the steel springs used by vehicles up to this time.^[4]

In practice, the system has always incorporated the desirable

This system performed remarkably well in straight ahead driving, including over uneven surfaces, but had little control over roll stiffness.^[5]

Millions of production vehicles have been built with variations on this system.

Electronic actuation of hydraulic suspension

Colin Chapman developed the original concept of computer management of hydraulic suspension in the 1980s to improve cornering in racing cars. Lotus fitted and developed a prototype system to a 1985 Excel with electro-hydraulic active suspension, but never offered it for sale to the public, although many demonstration cars were built for other manufacturers.

Sensors continually monitor body movement and vehicle ride level, constantly supplying the computer with new data. As the computer receives and processes data, it operates the hydraulic servos, mounted beside each wheel. Almost instantly, the servo-regulated suspension generates counter forces to body lean, dive, and squat during driving maneuvers.

Williams Grand Prix Engineering prepared an active suspension, devised by designer-aerodynamicist Frank Dernie, for the team's Formula 1 cars in 1992, creating such successful cars that the Fédération Internationale de l'Automobile decided to ban the technology to decrease the gap between Williams F1 team and its competitors.^[6]

Computer Active Technology Suspension (CATS) co-ordinates the best possible balance between

The 1999 Mercedes-Benz CL-Class (C215) introduced Active Body Control, where high pressure hydraulic servos are controlled by electronic computing, and this feature is still available. Vehicles can be designed to actively lean into curves to improve occupant comfort.^[7][8]

Active anti-roll bar

In fully active electronically controlled production cars, the application of electric servos and motors married to electronic computing allows for flat cornering and instant reactions to road conditions.

The Bose Corporation has a proof of concept model. The founder of Bose, Amar Bose, had been working on exotic suspensions for many years while he was an MIT professor.^[9]

Electromagnetic active suspension uses linear electromagnetic motors attached to each wheel. It provides extremely fast response, and allows regeneration of power consumed, by using the motors as generators. This nearly surmounts the issues of slow response times and high power consumption of hydraulic systems. Electronically controlled active suspension system (ECASS) technology was patented by the University of Texas Center for Electromechanics in the 1990s^[10] and has been developed by L-3 Electronic Systems for use on military vehicles.^[11] The ECASS-equipped Humvee exceeded the performance specifications for all performance evaluations in terms of absorbed power to the vehicle operator, stability and handling.

Active Wheel

• in-wheel electric traction motor.^[12][13]

• torsion bar and a lever which exerts up to 1,100 Nm (811.3 lb-ft) on the suspension via a coupling rod. Thanks to the front camera, the sedan detects bumps in the road early on and predictively adjusts the active suspension. Even before the car reaches a bump in the road, the preview function developed by Audi transmits the right amount of travel to the actuators and actively controls the suspension. The computer-controlled motors can sense imperfection on the road, and can raise the suspension up from the wheel which would go over the undulation, thus aiding the ride quality. The system will direct the motors on the outside to push up or pull down the suspension while cornering. This will result in a flatter drive and reduced body-roll around corners which in turn means more confident handling dynamics.^{[14][15][16][17][18][19][20]}

This type is the most economic and basic type of semi-active suspensions. They consist of a solenoid valve which alters the flow of the hydraulic medium inside the shock absorber, therefore changing the damping characteristics of the suspension setup. The solenoids are wired to the controlling computer, which sends them commands depending on the control algorithm (usually the so-called "Sky-Hook" technique).^{[citation needed]}

This type of system is used in

Another fairly recent method incorporates magnetorheological dampers with a brand name MagneRide. It was initially developed by Delphi Corporation for GM and was standard, as many other new technologies, for Cadillac STS (from model 2002), and on some other GM models from 2003. This was an upgrade for semi-active systems ("automatic road-sensing suspensions") used in upscale GM vehicles for decades. It allows, together with faster modern computers, changing the stiffness of all wheel suspensions independently. These dampers are finding increased usage in the US and already leases to some foreign brands, mostly in more expensive vehicles.^{[citation needed]}

This system was in development for 25 years. The damper fluid contains metallic particles. Through the onboard computer, the dampers' compliance characteristics are controlled by an electromagnet. Essentially, increasing the current flow into the damper magnetic circuit increases the circuit magnetic flux. This in turn causes the metal particles to change their alignment, which increases fluid viscosity thereby raising the compression/rebound rates, while a decrease softens the effect of the dampers by aligning the particles in the opposite direction. If we imagine the metal particles as dinner plates then whilst aligned so they are on edge - viscosity is minimised. At the other end of the spectrum they will be aligned at 90 degrees so flat. Thus making the fluid much more viscous. It is the electric field produced by the electromagnet that changes the alignment of the metal particles. Information from wheel sensors (about suspension extension), steering, acceleration sensors - and other data, is used to calculate the optimal stiffness at that point in time. The fast reaction of the system (milliseconds) allows, for instance, making a softer passing by a single wheel over a bump in the road at a particular instant in time.^{[citation needed]}

Production vehicles

This section possibly contains original research. Please improve it by verifying the claims made and adding inline citations. Statements consisting only of original research should be removed. (December 2017) (Learn how and when to remove this template message)

This section may lend create a more balanced presentation. Discuss and resolve this issue before removing this message. (December 2017)

By calendar year:

• 1954: Citroën Traction Avant 15-6H:, self-leveling Citroën hydropneumatic suspension on rear wheels.^{[citation needed]}
• 1955: Citroën DS, self-leveling Citroën hydropneumatic suspension on all four wheels.
• 1957:
  Cadillac Eldorado Brougham: premiere of self-leveling GM air suspension
• 1967: Rolls-Royce Silver Shadow Partial load bearing hydropneumatic suspension on all four wheels. Front system deleted in 1969^{[citation needed]}
• 1970: Citroën SM, self-leveling Citroën hydropneumatic suspension on all four wheels.^{[citation needed]}
• 1970: Citroën GS, self-leveling Citroën hydropneumatic suspension on all four wheels.
• 1974: Citroën CX, self-leveling Citroën hydropneumatic suspension on all four wheels.
• 1975: Mercedes Benz 450 SEL 6.9 Hydropneumatic suspension on all four wheels.
• 1982: Citroën BX, self-leveling Citroën hydropneumatic suspension on all four wheels.^{[citation needed]}
• 1979: Mercedes Benz W126 Hydropneumatic suspension on all four wheels as an option on the LWB v8 models
• 1983: Toyota Soarer: world first Electronically controlled (TEMS) that used a shock absorber control actuator (spring constant, variable attenuation force) installed^[21]
• 1985 Mercedes Benz 190E 2.3-16 Partial load bearing hydropneumatic suspension on all four wheels as an option on the 16v model. Standard on the Evo 1 and Evo 2 models
• 1985: Nissan introduced ultrasound
  semi-active suspension sensing "Super Sonic Suspension" optionally on the Cedric, Gloria and Nissan Laurel that integrated actuators inside the MacPherson struts on the front and rear suspension.^[22]
• 1986:
  Jaguar XJ40, self-leveling suspension.^[23]
• 1986: Mercedes Benz W126 Hydropneumatic suspension on all four wheels with electronically controlled adaptive damping as an option on the LWB v8 models
• 1987: Mitsubishi Galant (sixth generation) - features Active Controlled Suspension (Dynamic ECS). The system enables a comfortable ride and handling stability by automatically adjusting the vehicle height and damping force.
• 1989: Citroën XM - self-levelling, semi-active Hydractive on all four wheels with automatically adjusted spring rates and dampeners.
• 1989: Mercedes Benz R129 Partial load bearing hydropneumatic suspension with automatically adjusted spring rates and dampers as an option (ADS)
• 1990: Infiniti Q45 "Full-Active Suspension (FAS)", active suspension system, although it did still have conventional coil springs
• 1992: Toyota Celica (Toyota Electronically Modulated Suspension)
• 1992: Citroën Xantia VSX - self-levelling, semi-active Hydractive 2 on all four wheels, with automatically adjusted spring rates and dampeners.^{[citation needed]}
• 1993:
  continuously variable road sensing suspension) systems. It monitored damping rates of the shock absorbers every 15 milliseconds, selecting between two settings.^{[citation needed}
  ]
• 1994:
  Skyhook air suspension^[24]
• 1994: Citroën Xantia Activa - self-levelling, fully active Hydractive on all four wheels with hydraulic anti-roll bars and automatically adjusted spring rates and dampeners.
• 1998: Land Rover Discovery series 2 - Active Cornering Enhancement; an electronically controlled hydraulic anti-roll bar system was fitted to some versions, which reduced cornering roll.
• 1999: Mercedes Benz C215 Self leveling fully active hydraulic Active body control. Available on the S, CL and SL models
• 2000 Citroen C5 Hydractive 3 or Hydractive 3+
• 2002: Cadillac Seville STS, first MagneRide^[25]
• 2004: Volvo S60 R and V70 R (Four-C, a short name for "Continuously Controlled Chassis Concept", semi-active)
• 2006 Citroen C6 - Hydractive 3+
• 2010: Alfa Romeo MiTo Cloverleaf (DNA System based on Maserati's Skyhook technology)
• 2012: Jaguar XF Sportbrake, self-leveling air suspension.^[26]
• 2013:
  Magic body control
  . Self leveling fully active hydraulic system with road surface scanning electronics
• 2013: Volkswagen Mk7 Golf R User-Selectable Electronically Controlled Shock Dampening (Dynamic Chassis Control (DCC))
• 2019: Toyota Avalon Touring model (Adaptive Variable Suspension (AVS))
• 2025: Nio ET9 (SkyRide fully active suspension)^[27]

See also

• Toyota Active Control Suspension
• Hydropneumatic suspension
• Active Body control

References