Hybrid fiber-coaxial
This article has multiple issues. Please help improve it or discuss these issues on the talk page. (Learn how and when to remove these template messages)
|
Hybrid fiber-coaxial (HFC) is a broadband telecommunications network that combines optical fiber and coaxial cable. It has been commonly employed globally by cable television operators since the early 1990s.[1]
In a hybrid fiber-coaxial cable system, television channels are sent from the cable system's distribution facility, the
Description
The fiber optic network extends from the cable operators' master headend, sometimes to regional headends, and out to a neighborhood's hubsite, and finally to an optical to coaxial cable node which typically serves 25 to 2000 homes. A master headend will usually have satellite dishes for reception of distant video signals as well as IP aggregation routers. Some master headends also house telephony equipment (such as automatic telephone exchanges) for providing telecommunications services to the community.
A regional or area headend/hub will receive the video signal from the master headend
Separate Edge QAMs can be used to provide QAM modulated video suitable for transmission in a coaxial cable network, from digital video sources.[6][7] Edge QAMs can also be connected to a CMTS to provide internet data instead of video, in a modular CMTS architecture.[8][9] CCAPs aim to replace the conventional, integrated CMTS which only provides data and Edge QAMs used for video which are separate pieces of equipment.[10]
Video can be encoded according to standards such as NTSC, MPEG-2, DVB-C or the
The various services from CMTSs, CCAPs, Edge QAMs and QAM modulators are combined onto a single RF electrical signal using headend RF management modules such as splitters and combiners[16][17][18] and the resulting signals are inserted into a broadband optical transmitter which in practice is a transmitter module in an "optics platform" or headend platform such as an Arris CH3000, Scientific Atlanta Prisma, or a Cisco Prisma II.[19][20] These platforms host several transmitters and receivers the latter of which can be used for cable internet and can also host Erbium-Doped Fiber Amplifiers (EDFAs) to extend the reach of the optical signals in fiber optics.[21][22] Each transmitter and receiver services one optical node.[23]
This optical transmitter converts the RF electrical signal to a downstream optically modulated signal that is sent to the nodes. Fiber optic cables connect the headend or hub to the optical nodes in a
Fiber optic nodes
A fiber optic node has a broadband optical receiver, which converts the downstream optically modulated signal coming from the headend or hub to an electrical signal going to the customers. As of 2015,[update] the downstream signal is a RF modulated signal that typically begins at 50 MHz and ranges from 550 to 1000 MHz on the upper end. The fiber optic node also contains a reverse- or return-path transmitter that sends communication from customers back to the headend. In North America, this reverse signal is a modulated RF ranging from 5–42 MHz while in other parts of the world, the range is 5–65 MHz. This electrical signal is then outputted through coaxial cable to form a coaxial trunk.
The optical portion of the network provides a large amount of flexibility. If there are not many fiber-optic cables to the node,
Final connection to customers
The coaxial trunk portion of the network connects 25–2000 homes (500 is typical)[30] in a tree-and-branch configuration off of the node.[31][32]
Trunk coaxial cables are connected to the optical node[33][34] and form a coaxial backbone to which smaller distribution cables connect. RF amplifiers called trunk amplifiers are used at intervals in the trunk to overcome cable attenuation and passive losses of the electrical signals caused by splitting or "tapping" the coaxial cable. Trunk cables also carry AC power which is added to the cable line at usually either 60 or 90 V by a power supply (with a lead acid backup battery inside) and a power inserter. The power is added to the cable line so that optical nodes, trunk and distribution amplifiers do not need an individual, external power source.[35] The power supply might have a power meter next to it depending on local power company regulations.
From the trunk cables, smaller distribution cables are connected to a port of one of the trunk amplifiers called a bridger to carry the RF signal and the AC power down individual streets. Usually trunk amplifiers have two output ports: one for the trunk, and another as a bridger. Distribution amplifiers (also called system amplifiers) can be connected from a bridger port to connect several distribution cables to the trunk if more capacity is needed as they have multiple output ports. Alternatively, line extenders, which are smaller distribution amplifiers with only one output port, can be connected to the distribution cable coming off the bridger port in the trunk and used to boost the signals in the distribution cables[36] to keep the power of the television signal at a level that the TV can accept. The distribution line is then "tapped" into and used to connect the individual drops to customer homes.[37]
These RF taps pass the RF signal and block the AC power unless there are telephony devices that need the back-up power reliability provided by the coax power system.[38] The tap terminates into a small coaxial drop using a standard screw type connector known as an F connector.
The drop is then connected to the house where a ground block protects the system from stray voltages. Depending on the design of the network, the signal can then be passed through a splitter to multiple TVs or to multiple set top boxes (cable boxes) which may then be connected to a TV. If too many splitters are used to connect multiple TVs, the signal levels will decrease, and picture quality on analog channels will decrease. The signal in TVs past those splitters will lose quality and require the use of a "drop" or "house" amplifier to restore the signal.[39]
Evolution of HFC networks
Historically the trend among cable operators has been to reduce the amount of coaxial cable used in their networks to improve signal quality, which initially led to the adoption of HFC.[40] HFC replaced coaxial cable networks which had coaxial trunk cables originating at the headend of the network, and HFC replaced part of these trunk cables with fiber optic cables and optical nodes. In these networks, trunk amplifiers were placed along the trunk cables to maintain adequate signal levels in the trunks,[41][42] distribution feeder cables could be used to distribute signals from the trunks into individual streets,[43][44][45] directional couplers were used to improve signal quality,[46] trunk amplifiers could be equipped with automatic level control or automatic gain control,[47] hybrid amplifiers, which have a hybrid integrated circuit[48][49] could also be used,[50] and separate bridgers were used to connect the trunk to distribution feeders.[51][52][53]
In 1953,
To cope with needs for increased digital bandwidth such as for DOCSIS internet, cable operators have implemented expansions in the RF spectrum in HFC networks beyond 1 GHz to 1.2 GHz,[70][71] have transitioned to only handling IP traffic in the network, used digital transport adapters (DTAs) for transmitting normally analog signals, or used Switched Digital Video (SDV)[72][73] which allows the number of television channels in coaxial cables to be reduced without reducing the number of channels that are offered.[74][75]
Towards the end of the 1990s GaAs (Gallium Arsenide) transistors were introduced in HFC nodes and amplifiers, replacing silicon transistors which allowed an expansion of the spectrum used in HFC from 870 MHz to 1 GHz by 2006.[69] GaN transistors, introduced in 2008[48] and adopted in the 2010s allowed for another expansion to 1.2 GHz, or for expansion from 550 MHz to 750 MHz in older networks to 1 GHz without changing the spacing between amplifiers.[76][77][78]
Remote PHY is an evolution of the HFC network that aims to reduce the use of coaxial cable in the network and improve signal quality. In a conventional HFC network, headend equipment such as CMTSs and CCAPs are connected to the HFC network using RF interfaces which physically are coaxial cable connections[79][80][81] and optical signals in fiber optic cables in the network are analog. In Remote PHY, equipment such as CMTSs or CCAPs are connected directly to the HFC network using fiber optics carrying digital signals, eliminating the RF interface and coaxial cables at the CMTS/CCAP and RF modulation at the headend,[82] and replacing analog signals in fiber optic cables in the network, with digital signals such as 10 Gigabit Ethernet signals,[19] which eliminate the need for calibrating the HFC network bi-annually, extends the reach of the network, reduces the cost of equipment and maintenance,[83] and improves signal quality and allows for modulation such as 4096 QAM instead of 1024 QAM, allowing more information to be transmitted at a time, per bit. This requires more sophisticated optical nodes which can also convert signals from digital to analog performing modulation, unlike conventional optical nodes which only need to convert signals from optical to electrical.[82] These devices are known as Remote PHY devices (RPDs) or Remote MACPHY devices (RMDs). RPDs come in shelf variants which can be installed in apartment buildings (MDUs, multi dwelling units) and can also be installed in optical nodes or at a small hub which distributes signals similarly to a conventional HFC network.[19][73][84][36][85] Alternatively Remote PHY can allow for a CMTS/CCAP to be located in a remote data center away from customers.[86]
Remote MACPHY, besides achieving the same purpose as Remote PHY, also moves all DOCSIS protocol functionality to the optical node or the outside plant, which can reduce latency when compared to Remote PHY.[87][88] Remote CMTS/Remote CCAP builds upon this by moving all CMTS/CCAP functionality to the outside plant.[84][86] Distributed Access Architecture (DAA) covers Remote PHY and Remote MACPHY and has as the goal, moving functions closer to end customers, allowing for easier capacity expansions as centralized facilities for equipment are downsized or potentially eliminated, and newer DOCSIS versions beyond DOCSIS 3.1 with higher speeds. Remote PHY allows for some reuse of existing equipment such as CMTSs/CCAPs by replacing components.[87][89]
Virtual CCAPs (vCCAPs) or virtual CMTSs (vCMTSs) are implemented on commercial off the shelf x86-based servers with specialized software,[90] are often implemented alongside DAA[91] and can be used to increase service capacity without purchasing new CMTS/CCAP chassis, or add features to the CMTS/CCAP more quickly.[73]
Improving internet speeds for customers can be carried out by reducing the number of service groups with subscribers from 500 to no more than 128, in what is known as a n+0 architecture, with a single node and no amplifiers.
Transport over HFC network
By using
The HFC network is typically operated bi-directionally, meaning that signals are carried in both directions on the same network from the headend/hub office to the home, and from the home to the headend/hub office. The forward-path or downstream signals carry information from the headend/hub office to the home, such as video content, voice and Internet traffic. The very first HFC networks, and very old unupgraded HFC networks, are only one-way systems. Equipment for one-way systems may use POTS or radio networks to communicate to the headend.[101] HFC makes two-way communication over a cable network practical because it reduces the number of amplifiers in these networks.[1]
The return-path or upstream signals carry information from the home to the headend/hub office, such as control signals to order a movie or internet upstream traffic. The forward-path and the return-path are carried over the same coaxial cable in both directions between the optical node and the home.
To prevent interference of signals, the frequency band is divided into two sections. In countries that have traditionally used
Traditionally, since video content was sent only to the home, the HFC network was structured to be asymmetrical: one direction has much more data-carrying capacity than the other direction. The return path was originally used for only some control signals to order movies, etc., which required very little bandwidth. As additional services have been added to the HFC network, such as Internet access and telephony, the return path is being utilised more.
Multiple-system operators
One analog TV channel occupies a 6-MHz-wide frequency band in NTSC-based systems, or an 8-MHz-wide frequency band in PAL or SECAM-based systems. Each channel is centred on a specific frequency carrier so that there is no interference with adjacent or harmonic channels. To be able to view a digitally modulated channel, home, or customer-premises equipment (CPE), e.g. digital televisions, computers, or set-top boxes, are required to convert the RF signals to signals that are compatible with display devices such as analog televisions or computer monitors. The US Federal Communications Commission (FCC) has ruled that consumers can obtain a cable card from their local MSO to authorize viewing digital channels.
By using digital video compression techniques, multiple standard and high-definition TV channels can be carried on one 6 or 8 MHz frequency carrier, thus increasing the channel carrying capacity of the HFC network by 10 times or more versus an all-analog network.
Comparison to competing network technologies
Digital subscriber line (DSL) is a technology used by traditional telephone companies to deliver advanced services (high-speed data and sometimes video) over twisted pair copper telephone wires. It typically has lower data carrying capacity than HFC networks and data speeds can be range-limited by line lengths and quality.
Analogous to HFC,
In the 2000s, telecom companies started significant deployments of fiber to the x (FTTX) such as passive optical network solutions to deliver video, data and voice to compete with cable operators. These can be costly to deploy but they can provide large bandwidth capacity especially for data services.
See also
- Access network
- Backbone network
- Cable modem
- Cable modem termination system (CMTS)
- DOCSIS
- FTTLA
- Multimedia over Coax Alliance
- National Cable & Telecommunications Association(NCTA – US)
- Network service provider
- Radio frequency over glass (RFoG)
- Quadrature amplitude modulation
- MPEG-2
- Multichannel multipoint distribution service
- Society of Cable Television Engineers(SCTE – US)
References
- ^ ISBN 978-0-08-092214-0– via Google Books.
- ^ Kevin A. Noll. "Hybrid Fiber-Coaxial Networks: Technology and Challenges in Deploying Multi-Gigabit Access Services" (PDF). nanog.org. Retrieved March 30, 2023.
- ^ Data-Over-Cable Service Interface Specifications DOCSIS® 3.1 CCAP™ Operations Support System Interface Specification CM-SP-CCAP-OSSIv3.1-I25-220819
- ISBN 978-1-931695-37-4.
- ^ Emil Stoilov (2006). "On The Design of Hybrid Fiber-Coax Networks" (PDF). International Conference on Computer Systems and Technologies. Retrieved May 16, 2023.
- ^ https://www.cablefax.com/Assets/CT_QAM_Supplement_100108(3).pdf
- ^ https://people.computing.clemson.edu/~jmarty/papers/JCM81839_new.pdf
- ^ Chapman, John. "THE MODULAR CMTS ARCHITECTURE". Retrieved March 2, 2024.
- ^ "TRANSITIONING TO M-CMTS". Retrieved March 2, 2024.
- ^ "StackPath". www.lightwaveonline.com. September 13, 2013.
- ^ https://www.worldradiohistory.com/Archive-Communications-Technology/80s/Communications-Technology-1984-09.pdf
- ISBN 978-1-55860-828-3– via Google Books.
- ISBN 978-1-4200-3066-2.
- ^ "Cisco CMTS Router Downstream and Upstream Features Configuration Guide - DOCSIS 2.0 A-TDMA Modulation Profiles for the Cisco CMTS Routers [Support]".
- ^ "Configuring Cable Modulation Profiles on Cisco CMTSS".
- ^ https://www.nctatechnicalpapers.com/Paper/1996/1996-meeting-the-needs-of-the-headend-of-the-future-today-the-structured-headend/download
- ^ "_6EzSt-xXJIC".
- ISBN 978-0-08-051193-1.
- ^ a b c https://www.nctatechnicalpapers.com/Paper/2020/2020-the-power-of-distributed-access-architectures/download
- ^ https://www.normann-engineering.com/products/product_pdf/optical_transmission/arris/EN_CH3000.pdf
- ^ https://www.nctatechnicalpapers.com/Paper/1992/1992-optical-amplifier-basic-properties-and-system-modeling-a-simple-tutorial/download
- ^ https://www.cisco.com/c/dam/en/us/products/collateral/video/prisma-strand-mounted-optical-amplifier/product_data_sheet0900aecd806c3af2.pdf
- ^ https://www.nctatechnicalpapers.com/Paper/1997/1997-multi-layer-head-end-combining-network-design-for-broadcast-local-and-targeted-services/download
- ISBN 978-1-4822-8107-1– via Google Books.
- ISBN 978-1-55860-828-3.
- ISBN 978-0-08-051193-1.
- ^ "The FOA Reference for Fiber Optics - High Fiber Count Cables".
- ^ https://www.goamt.com/wp-content/uploads/2017/05/NC4000EG_OPTICAL-NODE-SERIES_AMT.pdf
- ^ https://www.commscope.com/globalassets/digizuite/1695-cable-technician-pocket-guide.pdf
- ^ Inc, IDG Network World (August 5, 1996). "Network World". IDG Network World Inc – via Google Books.
{{cite web}}
:|last=
has generic name (help) - ISBN 978-1-4822-8107-1– via Google Books.
- ISBN 978-0-85296-176-6– via Google Books.
- ^ https://www.ieee802.org/3/epoc/public/mar12/schmitt_01_0312.pdf
- ISBN 978-0-08-092214-0– via Google Books.
- ^ https://archive.nanog.org/sites/default/files/08-Noll.pdf
- ^ ISBN 978-0-08-092214-0.
- ^ "Taps: A Peek Under the Hood |". November 20, 2021.
- ISBN 978-0-08-092214-0– via Google Books.
- ISBN 978-90-5199-400-1.
- ISBN 978-2-7445-0144-9.
- ISBN 978-0-471-43802-1– via Google Books.
- ^ https://www.nctatechnicalpapers.com/Paper/1998/downloadyear/pdf
- ISBN 978-1-317-34793-4.
- ISBN 978-1-4831-9375-5.
- ISBN 978-0-240-80881-9.
- ^ https://www.worldradiohistory.com/Archive-TV-%26-Communications/TV-and-Communications/TV%26C-1964-12.pdf
- ^ "Paper - Distribution Equipment for 400 MHZ Co-Axial Communications Systems - NCTA Technical Papers".
- ^ a b c https://www.piedmontscte.org/resources/CATV%2BHybrid%2BAmplifier%2BModules%2BPast%242C%2BPresent%242C%2BFutureWP.pdf
- S2CID 6899727.
- ^ "Paper - the Design Approach to a New CATV Distribution Amplifier - NCTA Technical Papers".
- ^ "Paper - Performance of a 400 MHZ, 54 Channel, Cable Television Distribution System - NCTA Technical Papers".
- ^ "Paper - the Design, Construction, Cost and Performance the First 400 MHZ Cable Television System - NCTA Technical Papers".
- ISBN 978-1-4200-4131-6.
- ^ "TV Communications". Communications Publishing Corporation. March 11, 1975 – via Google Books.
- ^ a b c d https://syndeoinstitute.org/wp-content/uploads/2022/12/HistoryBetweenTheirEars-TaylorArcherS.pdf
- ^ https://www.worldradiohistory.com/Archive-DX/DX-Horizons/1965/TV%26C-1965-09.pdf
- ^ a b https://www.worldradiohistory.com/Archive-Communications-Technology/90s/Communicaation-Technology-1991-12.pdf
- ^ https://files.eric.ed.gov/fulltext/ED084875.pdf
- ^ "A Study of the Technical and Feasibility of Providing Narrowband and Broadband Communications Service in Rural Areas Volume 1".
- .
- ^ "Paper - Fiber Optic Technology for CATV Supertrunk Applications - NCTA Technical Papers".
- ^ https://www.worldradiohistory.com/Archive-C-ED/80s/C-ED-1987-12.pdf
- ^ https://syndeoinstitute.org/wp-content/uploads/2022/10/CableTimelineFall2015.pdf
- ^ "Broadband '89". March 12, 2024.
- ^ a b https://www.nctatechnicalpapers.com/Paper/1991/downloadyear/pdf
- ^ https://www.worldradiohistory.com/Archive-C-ED/80s/C-ED-1981-05.pdf
- ^ "Paper - Upgrade of 450/550 MHZ Cable Systems to 600 MHZ Using a Phase Area Approach - NCTA Technical Papers".
- ^ https://www.nctatechnicalpapers.com/Paper/1996/1996-750mhz-power-doubler-and-push-pull-catv-hybrid-modules-using-gallium-arsenide/download
- ^ a b https://www.nctatechnicalpapers.com/Paper/2019/2019-docsis-4-0-technology-realizing-multigigabit-symmetric-services/download
- ^ Ouyang, Tao. "Cable Lifespan Extension with FDX & ESD" (PDF). www.itu.int/. Retrieved March 2, 2024.
- ^ "ATX looks to DOCSIS 4.0 and beyond". April 22, 2020.
- ^ "The Switch to Switched Digital Video | NCTA — the Internet & Television Association".
- ^ a b c "Lessons from Operating Tens of Thousands of Remote PHY Devices". SCTE. Retrieved March 2, 2024.
- ^ https://www.lightreading.com/business-management/who-makes-what-switched-digital-video%7C
- ^ "Switched IP Video Technology Frees up to 80% of Bandwidth for DOCSIS Expansion". June 30, 2017.
- ^ https://www.nctatechnicalpapers.com/Paper/2013/2013-distributed-digital-hfc-architecture-expands-bi-directional-capacity/download
- ^ https://www.nctatechnicalpapers.com/Paper/2016/2016-hi-ho-hi-ho-to-a-gigabit-we-go/download
- ^ https://www.nctatechnicalpapers.com/Paper/2010/2010-refueling-the-cable-plant-a-new-alternative-to-gaas/download
- ISBN 978-0-08-051193-1.
- ^ "E6000™ Converged Edge Router User Documentation". Retrieved March 2, 2024.
- ^ "Demystifying OOB and R-PHY |". November 24, 2018.
- ^ a b c Jorge, Salinger. "Remote PHY: Why and How". SCTE. Retrieved March 2, 2024.
- ^ "Paper - Evolution of CMTS/CCAP Architectures - NCTA Technical Papers".
- ^ a b Chapman, John. "DOCSIS Remote PHY Modular Headend Architecture (MHA v2)" (PDF). SCTE. Retrieved March 2, 2024.
- ^ "Cisco Remote-PHY Compact Shelf Hardware Installation Guide" (PDF). Cisco Systems, Inc. Retrieved March 2, 2024.
- ^ a b "Impact of CCAP to CM Distance in a Remote PHY Architecture" (PDF). Retrieved March 2, 2024.
- ^ a b "Paper - Follow the Yellow Brick Road: From Integrated CCAP or CCAP + Remote PHY to FMA with Remote MACPHY - NCTA Technical Papers".
- S2CID 3668345.
- ^ "So, You Want to be a DOCSIS Engineer? You're Sure About This? |". February 17, 2023.
- ^ "Harmonic's 'CableOS' now connected to 18.4M modems".
- ^ "Practical Lessons of a DAA Deployment with a Virtualized CMTS". SCTE•ISBE. Retrieved March 2, 2024.
- ^ "Distributed Access Architecture Is Now Widely Distributed – And Delivering On It's Promise". SCTE. Retrieved March 2, 2024.
- ^ "Next-Generation HFC Part 1 – Upgrading the HFC Network". April 15, 2020.
- ^ https://www.nctatechnicalpapers.com/Paper/2019/2019-upgrading-the-plant-to-satisfy-traffic-demands/download
- ^ "https://www.nctatechnicalpapers.com/Paper/2019/2019-blueprint-for-3-ghz-25-gbps-docsis/download". SCTE•ISBE. Retrieved March 2, 2024.
{{cite web}}
: External link in
(help)|title=
- ^ "Complexity is Complex |". November 18, 2019.
- ^ a b "Paper - Network Capacity Options on the Path to 10G - NCTA Technical Papers".
- ^ "Paper - FDX & D3.1 Capacity Scenarios - NCTA Technical Papers".
- ^ https://www.lightreading.com/cable-technology/the-cable-fade-out-continues#close-modal
- ^ https://www.lightreading.com/cable-technology/cable-players-are-taking-many-paths-to-pon
- ISBN 978-1-59140-005-9 – via Google Books.)
{{cite book}}
: CS1 maint: multiple names: authors list (link