Repeated measures design

The article's lead section may need to be rewritten. Please help improve the lead and read the lead layout guide. (August 2017) (Learn how and when to remove this template message)

Repeated measures design is a research design that involves multiple measures of the same variable taken on the same or matched subjects either under different conditions or over two or more time periods.^[1] For instance, repeated measurements are collected in a longitudinal study in which change over time is assessed.

Crossover studies

A popular repeated-measures design is the

Randomized, controlled, crossover experiments are especially important in health care. In a randomized clinical trial, the subjects are randomly assigned treatments. When such a trial is a repeated measures design, the subjects are randomly assigned to a sequence of treatments. A crossover clinical trial is a repeated-measures design in which each patient is randomly assigned to a sequence of treatments, including at least two treatments (of which one may be a standard treatment or a placebo): Thus each patient crosses over from one treatment to another.

Nearly all crossover designs have "balance", which means that all subjects should receive the same number of treatments and that all subjects participate for the same number of periods. In most crossover trials, each subject receives all treatments.

However, many repeated-measures designs are not crossovers: the longitudinal study of the sequential effects of repeated treatments need not use any "crossover", for example (Vonesh & Chinchilli; Jones & Kenward).

Uses

• Limited number of participants—The repeated measure design reduces the variance of estimates of treatment-effects, allowing statistical inference to be made with fewer subjects.^[2]
• Efficiency—Repeated measure designs allow many experiments to be completed more quickly, as fewer groups need to be trained to complete an entire experiment. For example, experiments in which each condition takes only a few minutes, whereas the training to complete the tasks take as much, if not more time.
• Longitudinal analysis—Repeated measure designs allow researchers to monitor how participants change over time, both long- and short-term situations.

Order effects

Counterbalancing

In this technique, two groups each perform the same tasks or experience the same conditions, but in reverse order. With two tasks or conditions, four groups are formed.

Counterbalancing attempts to take account of two important sources of systematic variation in this type of design: practice and boredom effects. Both might otherwise lead to different performance of participants due to familiarity with or tiredness to the treatments.

Limitations

It may not be possible for each participant to be in all conditions of the experiment (i.e. time constraints, location of experiment, etc.). Severely diseased subjects tend to drop out of longitudinal studies, potentially biasing the results. In these cases

Mean regression may affect conditions with significant repetitions. Maturation may affect studies that extend over time. Events outside the experiment may change the response between repetitions.

Repeated measures ANOVA

Repeated measures analysis of variance (rANOVA) is a commonly used statistical approach to repeated measure designs.^[3] With such designs, the repeated-measure factor (the qualitative independent variable) is the within-subjects factor, while the dependent quantitative variable on which each participant is measured is the dependent variable.

Partitioning of error

One of the greatest advantages to rANOVA, as is the case with repeated measures designs in general, is the ability to partition out variability due to individual differences. Consider the general structure of the F-statistic:

F = MS_Treatment / MS_Error = (SS_Treatment/df_Treatment)/(SS_Error/df_Error)

In a between-subjects design there is an element of variance due to individual difference that is combined with the treatment and error terms:

SS_Total = SS_Treatment + SS_Error

df_Total = n − 1

In a repeated measures design it is possible to partition subject variability from the treatment and error terms. In such a case, variability can be broken down into between-treatments variability (or within-subjects effects, excluding individual differences) and within-treatments variability. The within-treatments variability can be further partitioned into between-subjects variability (individual differences) and error (excluding the individual differences):^[4]

SS_Total = SS_{Treatment (excluding individual difference)} + SS_Subjects + SS_Error

df_Total = df_{Treatment (within subjects)} + df_{between subjects} + df_error = (k − 1) + (n − 1) + ((n − k)(n − 1))

In reference to the general structure of the F-statistic, it is clear that by partitioning out the between-subjects variability, the F-value will increase because the sum of squares error term will be smaller resulting in a smaller MSError. It is noteworthy that partitioning variability reduces degrees of freedom from the F-test, therefore the between-subjects variability must be significant enough to offset the loss in degrees of freedom. If between-subjects variability is small this process may actually reduce the F-value.^[4]

Assumptions

As with all statistical analyses, specific assumptions should be met to justify the use of this test. Violations can moderately to severely affect results and often lead to an inflation of

• Normality—For each level of the within-subjects factor, the dependent variable must have a normal distribution.
• Sphericity—Difference scores computed between two levels of a within-subjects factor must have the same variance for the comparison of any two levels. (This assumption only applies if there are more than 2 levels of the independent variable.)
• Randomness—Cases should be derived from a random sample, and scores from different participants should be independent of each other.

The rANOVA also requires that certain multivariate assumptions be met, because a multivariate test is conducted on difference scores. These assumptions include:

• Multivariate normality—The difference scores are multivariately normally distributed in the population.
• Randomness—Individual cases should be derived from a random sample, and the difference scores for each participant are independent from those of another participant.

F test

As with other analysis of variance tests, the rANOVA makes use of an

• Standard Univariate ANOVA F test—This test is commonly used given only two levels of the within-subjects factor (i.e. time point 1 and time point 2). This test is not recommended given more than 2 levels of the within-subjects factor because the assumption of sphericity is commonly violated in such cases.
• Alternative Univariate test[6]—These tests account for violations to the assumption of sphericity, and can be used when the within-subjects factor exceeds 2 levels. The F statistic is the same as in the Standard Univariate ANOVA F test, but is associated with a more accurate p-value. This correction is done by adjusting the degrees of freedom downward for determining the critical F value. Two corrections are commonly used: the Greenhouse–Geisser correction and the Huynh–Feldt correction. The Greenhouse–Geisser correction is more conservative, but addresses a common issue of increasing variability over time in a repeated-measures design.^[7] The Huynh–Feldt correction is less conservative, but does not address issues of increasing variability. It has been suggested that lower Huynh–Feldt be used with smaller departures from sphericity, while Greenhouse–Geisser be used when the departures are large.
• Multivariate Test—This test does not assume sphericity, but is also highly conservative.

Effect size

One of the most commonly reported effect size statistics for rANOVA is partial eta-squared (η_p²). It is also common to use the multivariate η² when the assumption of sphericity has been violated, and the multivariate test statistic is reported. A third effect size statistic that is reported is the generalized η², which is comparable to η_p² in a one-way repeated measures ANOVA. It has been shown to be a better estimate of effect size with other within-subjects tests.^[8][9]

Cautions

rANOVA is not always the best statistical analysis for repeated measure designs. The rANOVA is vulnerable to effects from missing values, imputation, unequivalent time points between subjects and violations of sphericity.^[3] These issues can result in sampling bias and inflated rates of Type I error.^[10] In such cases it may be better to consider use of a linear mixed model.^[11]

See also

Notes