Roman bridge
The
History
Following the conquests of Tarquinius Priscus, Etruscan engineers migrated to Rome, bringing with them their knowledge of bridge-building techniques. The oldest bridge in ancient Rome was the Pons Sublicius.[2][3] It was built in the 6th century BCE by Ancus Marcius over the Tiber River.[3][4] The Romans improved on Etruscan architectural techniques. They developed the voussoir, stronger keystones, vaults, and superior arched bridges.[5][6] Roman arched bridges were capable of withstanding more stress by dispersing forces across bridges.[7] Many Roman bridges had semicircular arches, but a few were segmental, i.e. with an arc of less than 180 degrees.[8]
By the 2nd century BC, the Romans had further refined their bridge-building techniques, using stronger materials such as volcanic ash, lime and gypsum. Also, they began to use iron clamps to hold together bridges, constructing midstream arches, and pentagonal stones to allow for wider vaults.[9] According to Canadian classicist John Peter Oleson, no known stone bridges existed in Italy before the 2nd century BCE.[7][10] This view is not supported unanimously: Spanish engineer Leonardo Fernández Troyano suggested that stone bridges have existed since Pre-Roman Italy.[11][12]
Between 150 and 50 BCE, many stone Roman bridges were built, the Pons Aemilius being the first.[2][13] Engineers began to use stone instead of wood to exemplify the Pax Romana and to construct longer-lasting bridges.[14] These were the first large-scale bridges ever constructed.[9] Bridges were constructed by the Roman government to serve the needs of the military and the empire's administration. Sometimes roads and bridges were used for commercial purposes, but this was rare as boats better served the needs of the Roman economy.[15]
By the 2nd century Roman techniques had declined, and they had been mostly lost by the 4th century.[3] Some Roman bridges are still used today, such as the Pons Fabricius, and even after the Fall of the Western Roman Empire, engineers copied their bridges.[16] Roman bridge-building techniques persisted until the 18th century:[3] for example, the prevalence of arches in bridges can be attributed to the Romans.[15]
Construction
Measurements
Roman bridges were much larger than the bridges of other civilizations. They could be anywhere from 4.6 to 18.3 metres (15 to 60 ft) long. By the time of
Stone bridges
When building bridges across moving bodies of water, Roman engineers would begin by laying a foundation. At first, they used heavy timbers as
The Pons Aemilius probably had stone piers, with wooden roadbeds and arches.[2] They were rebuilt in stone in 142 BC, and either extended from the abutments to the piers, or vice versa. Throughout Roman history, brick or stone arches were used to support bridges' weight.[16] Roman engineers built bridges with one long arch instead of several smaller ones. This practice made construction easier, as they only needed to build one arch on land, instead of many in water. Roman arches were semi-circular and used voussoirs with equal dimensions and conic sections with equal circumference.[11][19] Later in Roman history arches started to become semi-circular.[20][21] Sometimes arches were segmented, or not semicircular.[8] This technique was invented by the Romans. Segmented arches allowed greater amounts of flood water to pass, preventing the bridge from being swept away and allowing it to be lighter. The Limyra Bridge in southwestern Turkey has 26 segmental arches with an average span-to-rise ratio of 5.3:1,[22] giving the bridge an unusually flat profile unsurpassed for more than a millennium.[23] The late Roman Karamagara Bridge in Cappadocia in eastern Turkey may represent the earliest surviving bridge featuring a pointed arch, though it is now submerged by the Keban Dam.[18] Roman arches were unable to properly fit into the arch springings, forcing the base of the arches upwards.
In the 2nd century, arches become thinner, and spandrels became flat and pierced with holes. They were constructed using a wooden frame to hold wedge-shaped blocks in place. Afterwards the wooden frame was removed, but the weight of the
Roman piers were thick enough to support the pressure of an arch. Stone arches allowed bridges to have much longer spans.[9] Usually, iron clamps covered in lead were used to build piers. Because of poor performance underwater, Roman piers were often destroyed over time.[15] Bridges that survived to the modern day were often furnished with cut waters on the upstream side and a flat downstream face, though some bridges, such as a bridge in Chester, are exceptions.[15]
Two niches carrying cornices were inserted between pilasters. They were then put above the framed starlings. Roman bridges had spandrels, between which images of dolphins were often inserted.[3] They rarely had wide spans and thick piers with bow-shaped piers that used small openings to allow for the flow of water. During construction, cranes were used to move materials and lift heavy objects.[25] Some bridges had aprons. They were used to surround piers. Usually, the aprons covered the area of the stream bed near the bridge.[15]
Brick bridges
Although Roman bricks were used to build many bridges, they were far more commonly used to build aqueducts. Bridges built from bricks were rare as bricks often failed to survive erosion.[27] The brick bridges that were built were generally used by the military, and they used construction techniques called opus vittatum and opus mixtum, the latter alternating rows of bricks in opus reticulatum.[14] Examples are bridges in Carmona, Palomas, Extremadura, and the Ponte della Chianche in Italy. One brick bridge in Ticino, Switzerland, has stone arches and brick spandrels.[11] Bricks were sometimes used to create parts of bridges, such as vaults, piers with welding joints, and brick and mortar rubble.[8]
Wooden bridges
Early Roman bridges were wooden, including one constructed by Apollodorus and the Pons Sublicius, the oldest bridge in ancient Rome, and they were probably common across northern Europe and the Tyrrhenian coast;[15] however, because of their lack of durability few have survived to the modern day.[28] These bridges were supported by wooden trestles spanned by horizontal timbers and reinforced with struts, and they were possibly cantilevered. In order to simplify the process of cutting trees, multiple shorter timbers were used.[3] Wooden poles were driven into the ground, and flat pieces of timber laid across them to create a flat surface.[29]
Other early techniques used to build wooden bridges involved barges, sometimes they were moored side by side. Workmen would raise weights, sometimes by rope, then it would fall down onto the piles. This method of construction, called pile driving, was necessary for wooden bridges to properly function. Because this technique created cofferdams, which are enclosures build to pump water out of an area.[30] The base for the foundation of the bridge would be put in this area.[15] Cofferdams were constructed of many piles held together. It is possible the piles were interconnected, likely to improve positioning, waterproofness, or both. Cofferdams would have been sealed with packed clay.[15] The cofferdams also needed to be consistently dry. In order to achieve this, engineers would use tools such as buckets to drain the water.[15] Wooden bridges could be burned to stop an attacker, or dismantled quickly.[7][31] For example, according to Livy, during a battle against the Sabines the Romans set one of their wooden bridges on fire, driving the enemy back.[32] Other early wooden bridges used post and lintel construction.
Pontoon bridges
Pontoon bridges were built by laying boats from side to side across a river.[29][5] During Julius Caesar's campaign in Germany, he built bridges by driving wooden piles into the stream bed from floating platforms and fixing beams at right angles across them to create trestles. Trajan built another bridge supported by stone during the Dacian Wars.[4] Roman engineers gradually developed new techniques to build bridges, such as oval-shaped bases and pierced bases to facilitate the movement of water. Many bridges would have marble reliefs or carvings, but these bridges were likely used exclusively by government officials because of the difficulty and expense of carving marble artwork.
Typology
There were three major types of Roman bridges. These were wooden, pontoon, and stone bridges. A list of Roman bridges compiled by the engineer Colin O'Connor features 330
There were two main types of wooden bridge in Britain. Small timber bridges with girders, and large ones made of stone and wood. Throughout the rest of the Roman world, except for northern Europe, arched bridges made of stone were common. This was likely due to the climate and rivers of the regions. Rivers were much calmer and water levels were lower in the southern parts of the Empire. This ensured foundations were easy to construct. While in the northern parts it was much harder to lay down foundations due to the high water level, muddy water, and substantial waterflow.[33]
Location
Europe | 830 | Asia | 74 | Africa | 57 |
---|---|---|---|---|---|
Italy | 460 | Turkey | 55 | Tunisia | 33 |
Spain | 142 | Syria | 7 | Algeria | 18 |
France | 72 | Jordan | 5 | Libya | 5 |
Germany | 30 | Lebanon | 4 | ||
United Kingdom | 29 | Israel | 2 | ||
Portugal | 14 | Iran | 1 | ||
Yugoslavia | 13 | ||||
Switzerland | 11 | ||||
Greece | 10 | ||||
Netherlands | 4 | ||||
Bulgaria | 3 | ||||
Luxemburg | 3 | ||||
Albania | 2 | ||||
Austria | 2 | ||||
Belgium | 2 | ||||
Romania | 2 | ||||
Hungary | 1 |
Opus pontis
The costs of building and repairing bridges, known as opus pontis ("bridge work"), were the responsibility of multiple local municipalities. Their shared costs prove Roman bridges belonged to the region overall, and not to any one town (or two, if on a border). The Alcántara Bridge in Lusitania, for example, was built at the expense of 12 local municipalities, whose names were added on an inscription.[35] Later, in the Roman Empire, the local lords of the land had to pay tithes to the empire for opus pontis.[36][37] The Anglo-Saxons continued this practice with bricg-geworc, a literal translation of opus pontis.[38]
Examples
Built in 142 BC, the Pons Aemilius, later named Ponte Rotto (broken bridge), is the oldest Roman stone bridge in Rome, with only one surviving arch and pier. However, evidence suggests only the abutment is original to the 2nd century BC while the arch and pier perhaps date to a reconstruction during the reign of Augustus (27 BC – 14 AD).[39] The Pons Fabricius, built in 62 BC during the late Republic, is the oldest Roman bridge that is still intact and in use.[40] The largest Roman bridge was Trajan's Bridge over the lower Danube, constructed by Apollodorus of Damascus, which remained for over a millennium the longest bridge to have been built both in terms of overall and span length.[41]
Large river bridging
Roman engineers built stone arch or stone pillar bridges over all major rivers of their Imperium, save two: the
See also
- List of Roman bridges
- Bridges in Rome
- Record-holding bridges in antiquity
- Roman architecture
- Roman architectural revolution
Footnotes
- ^ O'Connor 1993, p. 1
- ^ ISBN 978-0-8018-9188-5.
- ^ ISBN 978-0-486-42995-3.
- ^ ISBN 978-0-89236-705-4.
- ^ ISBN 978-1-4381-1027-1.
- ^ Robertson, D.S. (1943). Greek and Roman Architecture (2nd ed.). Cambridge University Press. p. 231.
The Romans were the first builders in Europe, perhaps the first in the world, fully to appreciate the advantages of the arch, the vault and the dome.
- ^ ISBN 978-0-19-973485-6.
- ^ a b c d Beall, Christine (1 September 1988). "Designing the segmental arch". The Aberdeen Group. Retrieved 21 March 2022 – via Concrete Construction.
- ^ ISBN 978-0-316-47380-4.
- ^ Oleson, John Peter (13 June 2018). "BRIEF BIOGRAPHY".
- ^ ISBN 978-0-7277-3215-6.
- ^ "main". CFCSL. Retrieved 12 March 2022.
- ISBN 978-3-540-77618-5.
- ^ a b Bove, L.; Bergamasco, I.; Lippiello, M. (2004). The Stone Bridges in Southern Italy: From the Roman Tradition to the Middle of the 19th Centuries. Dipartimento di Costruzioni e Metodi Matematici in Architettura Università degli Studi di Napoli – Facoltà di Architettura. pp. 3–4.
- ^ ISBN 978-1-351-91928-9.
- ^ ISBN 978-1-4042-0556-7.
The ends of the bridge called abutments, were built on each side, and piers were situated in the middle. The abutments and piers carried most of the bridge's weight.
- ISBN 978-0-19-517072-6.
- ^ a b Galliazzo 1995, pp. 92, 93 (fig. 39)
- ^ a b Galliazzo 1994, p. 2 (Indice)
- ^ Galliazzo 1995, pp. 429–437
- ^ O'Connor 1993, p. 171
- ^ O'Connor 1993, p. 126
- ^ a b O'Connor 1993, p. 187ff
- ISBN 978-1-7253-4154-8.
- ^ ISBN 978-3-030-29227-0.
- ISBN 978-1-351-44047-9.
- ISBN 978-0-521-47071-1.
- ISBN 978-1-135-45932-1.
- ^ ISBN 978-0-19-537986-0.
- ^ Chisholm, Hugh, ed. (1911). "Cofferdam" . Encyclopædia Britannica. Vol. 6 (11th ed.). Cambridge University Press. p. 649.
- ^ Landart, Paula (5 December 2021). Finding Ancient Rome: Walks in the city. Paula Landart. pp. 45–46.
- ^ Livius, Titus. Early History of Rome (PDF). p. 43.
- ISBN 978-0-19-927274-7.
- Byzantinestructures.
- ^ Frothingham, A.I. (1915). "The Roman Territorial Arch". American Journal of Archaeology. 14 (19). Macmillan Company: 159, 172.
- ISBN 9782840503736. Retrieved 15 July 2017.
- ISBN 9781603835084. Retrieved 15 July 2017.
- ^ Bosworth, Joseph (1882). An Anglo-Saxon Dictionary: Based on the Manuscript Collections of the Late Joseph Bosworth ... Clarendon Press. p. 125. Retrieved 15 July 2017.
- ^ Platner, Samuel Ball, A Topographical Dictionary of Ancient Rome, ed. Ashby, Thomas, London: Oxford University Press, 1929 [Thayer, Bill (17 May 2020) "Pons Aemilius", University of Chicago, Accessed 9 June 2021]
- ISBN 978-88-8265-100-8.
- ^ Where are the Greatest Bridges of Ancient Rome?, retrieved 5 September 2023
- ^ O'Connor 1993, pp. 193–202 (Appendices A and B) Categories
- ^ O'Connor 1993, pp. 133–139
References
- Fuentes, Manuel Durán: La construcción de puentes romanos en Hispania, Xunta de Galicia, Santiago de Compostela 2004, ISBN 978-84-453-3937-4
- Fernández Troyano, Leonardo (2003), Bridge Engineering. A Global Perspective, London: Thomas Telford Publishing, ISBN 0-7277-3215-3
- Galliazzo, Vittorio (1995), I ponti romani, vol. 1, Treviso: Edizioni Canova, ISBN 88-85066-66-6
- Galliazzo, Vittorio (1994), I ponti romani. Catalogo generale, vol. 2, Treviso: Edizioni Canova, ISBN 88-85066-66-6
- Gazzola, Piero (1963), Ponti romani. Contributo ad un indice sistematico con studio critico bibliografico, Florence
{{citation}}
: CS1 maint: location missing publisher (link) - O'Connor, Colin (1993), Roman Bridges, Cambridge University Press, ISBN 0-521-39326-4
External links
- Traianus - Technical investigation of Roman public works
- The Waters of Rome: Tiber River Bridges and the Development of the Ancient City of Rome
- Livius.org: Pontes longi – Roman bog bridges