Small Astronomy Satellite 3

Small Astronomy Satellite 3

Small Astronomy Satellite 3
Mission type	X-ray astronomy
Operator	NASA
COSPAR ID	1975-037A
SATCAT no.	07788
Mission duration	4 years
Spacecraft properties
Manufacturer	APL · Johns Hopkins University
Launch mass	196.7 kilograms (434 lb)
Power	65.0 watts
Start of mission
Launch date	7 May 1975, 22:45:01 (1975-05-07UTC22:45:01Z) UTC
Rocket	San Marco
End of mission
Decay date	9 April 1979 (1979-04-10)
Orbital parameters
Reference system	Geocentric
Regime	LEO
Eccentricity	0.0000313
Perigee altitude	509.0 kilometers (316.3 mi)
Apogee altitude	516.0 kilometers (320.6 mi)
Inclination	3.0033°
Period	94.90 minutes
RAAN	13.5403 degrees
Argument of perigee	37.2127 degrees
Mean anomaly	322.7960 degrees
Mean motion	16.22945651
Epoch	8 April 1979
Revolution no.	21935
Explorers Program ← Explorer 52 Explorer 54  →

The Small Astronomy Satellite 3 (SAS 3, also known as SAS-C before launch) was a NASA

The spacecraft was 3-axis stabilized with a momentum wheel that was used to establish stability about the nominal rotation, or z-axis. The orientation of the z-axis could be altered over a period of hours using magnetic torque coils that interacted with the Earth's magnetic field. Solar panels charged batteries during the daylight portion of each orbit, so that SAS 3 had essentially no expendables to limit its lifetime beyond the life of the tape recorders, batteries, and orbital drag. The spacecraft typically operated in a rotating mode, spinning at one revolution per 95-min orbit, so that the LEDs, tube and slat collimator experiments, which looked out along the y-axis, could view and scan the sky almost continuously. The rotation could also be stopped, allowing extended (up to 30 min) pointed observations of selected sources by the y-axis instruments. Data were recorded on board by magnetic tape recorders, and played back during station passes every orbit.[3]

SAS 3 was commanded from the NASA Goddard Space Flight Center (GSFC) in Greenbelt MD, but data were transmitted by modem to MIT for scientific analysis, where scientific and technical staff were on-duty 24 hours a day. The data from each orbit were subjected to quick-look scientific analysis at MIT before the next orbital station pass, so the science operational plan could be altered by telephoned instruction from MIT to GSFC in order to study targets in near real-time.

Launch

The spacecraft was launched from the

Explorer 53 (SAS-C) was a small spacecraft whose objectives were to survey the celestial sphere for sources radiating in the X-ray, gamma ray, ultraviolet, and other spectral regions. The primary missions of Explorer 53 were to measure the X-ray emission of discrete extragalactic sources, to monitor the intensity and spectra of galactic X-ray sources from 0.2 to 60-keV, and to monitor the X-ray intensity of Scorpio X-1.^[5]

Experiments

Extragalactic Experiment (EGE)

This experiment determined the positions of very weak extragalactic X-ray sources. The instrument viewed a 100-sq degree region of the sky around the direction of the spin axis of the satellite. The nominal targets for a 1-year study were: (1) the Virgo Cluster of galaxies for 4 months, (2) the galactic equator for 2 months, (3) the Andromeda Nebula for 3 months, and (4) the Magellanic Clouds for 3 months. The instrumentation consisted of one 2.5-arc-minutes and one 4.5-arc-minutes Full width at half maximum (FWHM) modulation collimator, as well as proportional counters sensitive over the energy range from 1.5 to 10-keV. The effective area of each collimator was about 225-cm². The aspect system provided information on the orientation of the collimators to an accuracy of 15-arc-seconds.^[6]

Galactic Absorption Experiment (GAE)

The density and distribution of interstellar matter was determined by measuring the variation in the intensity of the low-energy diffuse X-ray background as a function of galactic latitude. A 1-micrometer polypropylene window proportional counter was used for the 0.1- to 0.4-keV and 0.4- to 1.0-keV energy ranges, while a 2-micrometer titanium window counter covered the energy range from 0.3 to 0.5 keV. In addition, two 1-mm beryllium window counters were used for the 1.0- to 10-keV energy range. The collimators in this experiment had fields of view of 3° for the 1-micrometer counter, 2° for the 2-micrometer counter, and 2° for the 1-mm counters.^[7]

Galactic Monitor Experiment (GME)

The objectives of this experiment were to locate galactic X-ray sources to 15 arc-seconds and to monitor these sources for intensity variations. The source positions were determined with the use of the modulation collimators of the Extragalactic Experiment during the nominal 2-month observation of the galactic equator. The monitoring of the X-ray sky was accomplished by the use of three slat collimators. One collimator, 1° by 70° FWHM, was oriented perpendicular to the equatorial plane of the satellite, while the other two, each 0.5° by 45° FWHM, were oriented 30° above and 30° below the first. The detector behind each collimator was a proportional counter, sensitive from 1.5 to 13-keV, with an effective area of about 100-cm². The 1.0° collimator had an additional counter of the same area, sensitive from 8 to 50-keV. Three lines of position were obtained for any given source when the satellite was being spun at a steady rotation of 4 arc-minutes/seconds about the Z-axis.^[8]

Scorpio Monitor Experiment (SME)

A 12° by 50° FWHM slat collimator was oriented with its long axis perpendicular to the satellite spin axis such that a given point on the sky could be monitored for about 25% of a rotation. This collimator was inclined by 31° with respect to the equatorial plane of the satellite, so that Scorpio X-1 was observed while the Z-axis was oriented to the Virgo Cluster of galaxies. The detectors used in this experiment were proportional counters with 1-mm beryllium windows. The energy range was from 1.0 to 60-keV, and the total effective area was about 40-cm².^[9]

Research results

SAS 3 was especially productive due to its flexibility and rapid responsiveness. Among its most important results were:

• Shortly after the discovery of the first X-ray burster by the ANS, an intense period of burst source discovery by SAS 3 quickly led to the discovery and characterization of about a dozen additional objects, including the famous Rapid Burster,^[10] MXB1730-335.^[11][12] These observations established the identification of bursting X-ray sources with neutron star binary systems.
• The RMC was the first instrument to routinely provide X-ray positions that were sufficiently precise to allow followup by optical observatories to establish X-ray/optical counterparts, even in crowded regions near the galactic plane. Roughly 60 positions were obtained with accuracies on the order of 1 arcminute or less. The resulting source identifications helped to connect X-ray astronomy to the main body of stellar astrophysics.
• Discovery of the 3.6 s pulsations of the transient neutron star/Be star binary 4U 0115+63.,^[13] leading to determination of its orbit and observation of a cyclotron absorption line in its strong magnetic field. Many Be star/neutron star binaries were subsequently discovered as a class of X-ray emitters.
• Discovery of X-ray emission from HZ 43 (an isolated white dwarf),
  AM Her,^[15]
  the first highly magnetic white dwarf binary system seen in X rays.
• Established the frequent location of X-ray sources near the centers of globular clusters.
• First identification of a QSO through its X-ray emission.
• The soft X-ray instrument established that the 0.10-28 keV diffuse intensity is generally inversely correlated with the neutral H column density, indicating absorption of external diffuse sources by the foreground galactic interstellar medium.^[16]

Lead investigators on SAS 3 were MIT professors

• Small Astronomy Satellite 1
• Small Astronomy Satellite 2

Notes