SuperDraco

Source: Wikipedia, the free encyclopedia.
SuperDraco
DragonFly

SuperDraco is a

fault-tolerant propulsion for use as a launch escape system for the SpaceX Dragon 2, a passenger-carrying space capsule
.

SuperDraco rocket engines utilize a

storable (non-cryogenic) hypergolic propellant which allows the engines to be fired many months after fueling and launch. They combine the functions of both a reaction control system and a main propulsive engine. Hypergolic fuels do not require an external source of ignition, providing increased reliability for the spacecraft.[7]

The engines are used on crew transport flights to low Earth orbit, and were also projected to be used for entry, descent and landing control of the now-canceled Red Dragon to Mars.

SuperDracos are used on the

throttled to 68,170 newtons (15,325 lbf) to maintain vehicle stability.[6]

History

On February 1, 2012 SpaceX announced that it had completed the development of a new, more powerful version of a

CCDev 2
program.

Name: Draco comes from the Greek drakōn for dragon. Draco (constellation) is a constellation (the Dragon) in the polar region of the Northern Hemisphere near Cepheus and Ursa Major.

Design

SuperDraco engines use a

deeply reduce their thrust providing precise control during propulsive landing of the Dragon capsule.[9]

SuperDraco is the third most powerful engine developed by SpaceX. It is approximately 200 times

Merlin 1D engine, and expected to be 1/26th as powerful as the SpaceX Raptor
engine.

In addition to the use of the SuperDraco thrusters for powered-landings on Earth, NASA's Ames Research Center was studying the feasibility of a Dragon-derived Mars lander for scientific investigation until 2017.[11] Preliminary analysis in 2011 indicated that the final deceleration would be within the retro-propulsion SuperDraco thruster capabilities.[11][12]

SuperDraco is designed to be highly

throttleable, from 100 to 20% of full thrust.[8] This would have been used for precision controllable propulsive landings
of the Dragon V2 spacecraft.

Engine testing

SuperDraco test-fire mosaic

The SuperDraco engine development program had an extensive

test program that spanned several years. As of December 2012, the SuperDraco ground-test engines had been fired a total of 58 times for a total firing-time duration of 117 seconds and SpaceX expressed hope that the test results would exceed the original requirements for the engine.[13]

A second version of the engine was developed in 2013, this one manufactured with

casting technique. By July 2014, the 3D-printed engine combustion chamber had been fired over 80 times, for a total duration of more than 300 seconds, and it likewise completed a full qualification test.[8]

The SuperDraco completed qualification testing in May 2014 – including testing "across a variety of conditions including multiple starts, extended firing durations and extreme off-nominal propellant flow and temperatures."[9]

By January 2015, SpaceX demonstrated the SuperDraco engine pod with full functionality at McGregor, Texas. Four of these engine pods, each containing two SuperDraco engines, will be used in the Dragon 2 crewed spacecraft.[14]

In April 2015, SpaceX and NASA set a timeframe to test a Dragon 2's SuperDraco engines with a pad abort test. The test eventually occurred on May 6, 2015, from a test stand at

SLC-40.[15] and was successful.[16]

On April 20, 2019, the SpaceX Crew Dragon capsule used on DM-1 was destroyed during a test of the SuperDraco engines at Landing Zone 1.[17]

Manufacturing

On September 5, 2013 Elon Musk tweeted an image of a regeneratively cooled SuperDraco rocket chamber emerging from an EOS 3D metal printer, and indicated that it was composed of the Inconel superalloy.[18] This was later shown to be the production technique for the flight-level engines.

It was announced in May 2014 that the flight-qualified version of the SuperDraco engine is the first[

direct metal laser sintering, and operates at a chamber pressure 6,900 kilopascals (1,000 psi) at a very high temperature.[clarification needed] The engines are contained in a printed protective nacelle to prevent fault propagation in the event of an engine failure.[1][19][20]

The ability to 3D print the complex parts was key to achieving the low-mass objective of the engine. According to Elon Musk, "It’s a very complex engine, and it was very difficult to form all the cooling channels, the injector head, and the throttling mechanism. Being able to print very high strength advanced alloys ... was crucial to being able to create the SuperDraco engine as it is."[21]

The 3D printing process for the SuperDraco engine dramatically reduces

materials properties."[8]

According to Elon Musk, cost reduction through 3D printing is also significant, in particular because SpaceX can print an hourglass chamber where the entire wall consists of internal cooling channels, which would be impossible without additive manufacturing.[22]

See also

References

  1. ^ a b c Bergin, Chris (2014-05-30). "SpaceX lifts the lid on the Dragon V2 crew spacecraft". NASAspaceflight.com. Retrieved 2014-05-30.
  2. ^ a b c d "SpaceX Demonstrates Astronaut Escape System for Crew Dragon Spacecraft". NASA. 6 May 2015. Retrieved 7 May 2015.
  3. ^ a b c "Archived copy" (PDF). Archived from the original (PDF) on 2020-07-18. Retrieved 2019-09-24.{{cite web}}: CS1 maint: archived copy as title (link)
  4. ^ "SpaceX Completes Qualification Testing of SuperDraco Thruster". 2014-05-28.
  5. ^ "SuperDraco | Test Fire". YouTube. 2015-11-10.
  6. ^ a b c James, Michael; Salton, Alexandria; Downing, Micah (November 12, 2013), Draft Environmental Assessment for Issuing an Experimental Permit to SpaceX for Operation of the Dragon Fly Vehicle at the McGregor Test Site, Texas, May 2014 – Appendices (PDF), Blue Ridge Research and Consulting, LCC, p. 12
  7. ISBN 978-0-8135-0725-5
    .
  8. ^ a b c d "SpaceX Launches 3D-Printed Part to Space, Creates Printed Engine Chamber for Crewed Spaceflight". SpaceX. 2014-07-31. Retrieved 2014-08-01. Compared with a traditionally cast part, a printed [part] has superior strength, ductility, and fracture resistance, with a lower variability in materials properties. ... The chamber is regeneratively cooled and printed in Inconel, a high performance superalloy. Printing the chamber resulted in an order of magnitude reduction in lead-time compared with traditional machining – the path from the initial concept to the first hotfire was just over three months. During the hotfire test, ... the SuperDraco engine was fired in both a launch escape profile and a landing burn profile, successfully throttling between 20% and 100% thrust levels. To date the chamber has been fired more than 80 times, with more than 300 seconds of hot fire.
  9. ^ a b "SuperDraco Thruster Powers Revolutionary Launch Escape System (Rocket Thruster Test)". Satnews Daily. 2014-05-27. Retrieved 2014-05-28.
  10. ^ "SpaceX Test Fires Engine Prototype for Astronaut Escape System". NASA. 2012-02-01. Retrieved 2012-02-01.
  11. ^ a b "Red Dragon" (PDF), Feasibility of a Dragon-derived Mars lander for scientific and human-precursor investigations, 8m.net, October 31, 2011, archived from the original (PDF) on 2012-06-16, retrieved 2012-05-14
  12. ^ "NASA ADVISORY COUNCIL (NAC) - Science Committee Report" (PDF). Ames Research Center, NASA. 1 November 2011. Archived from the original (PDF) on 2013-01-20. Retrieved 2012-05-01.
  13. ^ Staff (2012-12-14). "NASA's Return On Investment Report" (PDF). Retrieved 2015-12-30.
  14. ^ "Full functionality of Crew Dragon's SuperDraco jetpacks demonstrated with hotfire test in McGregor, TX". vine.co. Vine. Retrieved 24 January 2015.
  15. ^ Clark, Stephen (21 April 2015). "Dragon pad abort test set for early May". Spaceflight Now.
  16. ^ Berger, Eric (2016-04-30). "From zero to 100mph in 1.2 seconds, the SuperDraco thruster delivers". Ars Technica. Retrieved 2017-02-04.
  17. ^ "SpaceX Crew Dragon spacecraft destroyed in test mishap, company confirms". www.cbsnews.com. Retrieved 2019-05-03.
  18. ^ @elonmusk (September 5, 2013). "SpaceX SuperDraco inconel rocket chamber w regen cooling jacket emerges from EOS 3D metal printer" (Tweet) – via Twitter.
  19. ^ Norris, Guy (2014-05-30). "SpaceX Unveils 'Step Change' Dragon 'V2'". Aviation Week. Archived from the original on 2014-05-31. Retrieved 2014-05-30.
  20. ^ Kramer, Miriam (2014-05-30). "SpaceX Unveils Dragon V2 Spaceship, a Manned Space Taxi for Astronauts — Meet Dragon V2: SpaceX's Manned Space Taxi for Astronaut Trips". space.com. Retrieved 2014-05-30.
  21. ^ Foust, Jeff (2014-05-30). "SpaceX unveils its "21st century spaceship"". NewSpace Journal. Retrieved 2014-05-31.
  22. ^ Elon Musk, Mike Suffradini (7 July 2015). Elon Musk comments on Falcon 9 explosion - Huge Blow for SpaceX (2015.7.7) (video). Archived from the original on 2015-09-06. Retrieved 2015-12-30.
Retrieved from "https://en.wikipedia.org/w/index.php?title=SuperDraco&oldid=1217323885"