Intel Core (microarchitecture)

The Intel Core microarchitecture (provisionally referred to as Next Generation Micro-architecture,^[1] and developed as Merom)^[2] is a multi-core processor microarchitecture launched by Intel in mid-2006. It is a major evolution over the Yonah, the previous iteration of the P6 microarchitecture series which started in 1995 with Pentium Pro. It also replaced the NetBurst microarchitecture, which suffered from high power consumption and heat intensity due to an inefficient pipeline designed for high clock rate. In early 2004 the new version of NetBurst (Prescott) needed very high power to reach the clocks it needed for competitive performance, making it unsuitable for the shift to dual/multi-core CPUs. On May 7, 2004 Intel confirmed the cancellation of the next NetBurst, Tejas and Jayhawk.^[3] Intel had been developing Merom, the 64-bit evolution of the Pentium M, since 2001,^[2] and decided to expand it to all market segments, replacing NetBurst in desktop computers and servers. It inherited from Pentium M the choice of a short and efficient pipeline, delivering superior performance despite not reaching the high clocks of NetBurst.^[a]

The first processors that used this architecture were code-named '

While the Core microarchitecture is a major architectural revision, it is based in part on the

Core can speculatively execute loads ahead of preceding stores with unknown addresses.^[9]

Other new technologies include 1 cycle throughput (2 cycles previously) of all 128-bit SSE instructions and a new power saving design. All components will run at minimum speed, raising speed dynamically as needed (similar to AMD's Cool'n'Quiet power-saving technology, and Intel's own SpeedStep technology from earlier mobile processors). This allows the chip to produce less heat, and minimize power use.

For most Woodcrest CPUs, the

Previously, Intel announced that it would now focus on power efficiency, rather than raw performance. However, at Intel Developer Forum (IDF) in spring 2006, Intel advertised both. Some of the promised numbers were:

• 20% more performance for Merom at the same power level; compared to
  Core Duo
• 40% more performance for Conroe at 40% less power; compared to Pentium D
• 80% more performance for Woodcrest at 35% less power; compared to the original dual-core Xeon

Processor cores

The processors of the Core microarchitecture can be categorized by number of cores, cache size, and socket; each combination of these has a unique code name and product code that is used across several brands. For instance, code name "Allendale" with product code 80557 has two cores, 2 MB L2 cache and uses the desktop socket 775, but has been marketed as Celeron, Pentium, Core 2, and Xeon, each with different sets of features enabled. Most of the mobile and desktop processors come in two variants that differ in the size of the L2 cache, but the specific amount of L2 cache in a product can also be reduced by disabling parts at production time. Tigerton dual-cores and all quad-core processors except - are multi-chip modules combining two dies. For the 65 nm processors, the same product code can be shared by processors with different dies, but the specific information about which one is used can be derived from the stepping.

Conroe/Merom (65 nm)

The original Core 2 processors are based on the same dies that can be identified as

Additional code names for processors based on this model are Woodcrest (LGA 771, 4 MB L2 cache), Clovertown (MCM, LGA 771, 2×4MB L2 cache) and Tigerton (MCM, Socket 604, 2×4MB L2 cache), all of which are marketed only under the Xeon brand.

Conroe-L/Merom-L

The Conroe-L and Merom-L processors are based around the same core as Conroe and Merom, but only contain a single core and 1 MB of L2 cache, significantly reducing production cost and power consumption of the processor at the expense of performance compared to the dual-core version. It is used only in ultra-low voltage Core 2 Solo U2xxx and in Celeron processors and is identified as CPUID family 6 model 22.

Penryn/Wolfdale (45 nm)

In Intel's

Architecturally, 45 nm Core 2 processors feature SSE4.1 and new divide/shuffle engine.[12]

The chips come in two sizes, with 6 MB and 3 MB L2 cache. The smaller version is commonly called Penryn-3M and Wolfdale-3M and Yorkfield-6M, respectively. The single-core version of Penryn, listed as Penryn-L here, is not a separate model like Merom-L but a version of the Penryn-3M model with only one active core.

Dunnington

The Xeon "Dunnington" processor (CPUID Family 6, model 29) is closely related to Wolfdale but comes with six cores and an on-chip L3 cache and is designed for servers with Socket 604, so it is marketed only as Xeon, not as Core 2.

Steppings

The Core microarchitecture uses several stepping levels (steppings), which unlike prior microarchitectures, represent incremental improvements, and different sets of features like cache size and low power modes. Most of these steppings are used across brands, typically by disabling some features and limiting clock frequencies on low-end chips.

Steppings with a reduced cache size use a separate naming scheme, which means that the releases are no longer in alphabetic order. Added steppings have been used in internal and engineering samples, but are unlisted in the tables.

Many of the high-end Core 2 and Xeon processors use Multi-chip modules of two chips in order to get larger cache sizes or more than two cores.

Steppings using 65 nm process

Early ES/QS steppings are: B0 (CPUID 6F4h), B1 (6F5h) and E0 (6F9h).

Steppings B2/B3, E1, and G0 of model 15 (cpuid 06fx) processors are evolutionary steps of the standard Merom/Conroe die with 4 MB L2 cache, with the short-lived E1 stepping only being used in mobile processors. Stepping L2 and M0 are the Allendale chips with just 2 MB L2 cache, reducing production cost and power consumption for low-end processors.

The G0 and M0 steppings improve idle power consumption in C1E state and add the C2E state in desktop processors. In mobile processors, all of which support C1 through C4 idle states, steppings E1, G0, and M0 add support for the Mobile Intel 965 Express (Santa Rosa) platform with Socket P, while the earlier B2 and L2 steppings only appear for the Socket M based Mobile Intel 945 Express (Napa refresh) platform.

The model 22 stepping A1 (cpuid 10661h) marks a significant design change, with just a single core and 1 MB L2 cache further reducing the power consumption and manufacturing cost for the low-end. Like the earlier steppings, A1 is not used with the Mobile Intel 965 Express platform.

Steppings G0, M0 and A1 mostly replaced all older steppings in 2008. In 2009, a new stepping G2 was introduced to replace the original stepping B2.^[16]

Steppings using 45 nm process

In the model 23 (cpuid 01067xh), Intel started marketing stepping with full (6 MB) and reduced (3 MB) L2 cache at the same time, and giving them identical cpuid values. All steppings have the new SSE4.1 instructions. Stepping C1/M1 was a bug fix version of C0/M0 specifically for quad core processors and only used in those. Stepping E0/R0 adds two new instructions (XSAVE/XRSTOR) and replaces all earlier steppings.

In mobile processors, stepping C0/M0 is only used in the Intel Mobile 965 Express (Santa Rosa refresh) platform, whereas stepping E0/R0 supports the later Intel Mobile 4 Express (Montevina) platform.

Model 30 stepping A1 (cpuid 106d1h) adds an L3 cache and six instead of the usual two cores, which leads to an unusually large die size of 503 mm².

System requirements

Motherboard compatibility

Conroe, Conroe XE and Allendale all use Socket LGA 775; however, not every motherboard is compatible with these processors.

Supporting chipsets are:

• Intel: 865G/PE/P, 945G/GZ/GC/P/PL, 965G/P, 975X, P/G/Q965, Q963, 946GZ/PL, P3x, G3x, Q3x, X38, X48, P4x, 5400 Express (See also: List of Intel chipsets
  )
• Nvidia: nForce4 Ultra/SLI X16 for Intel, nForce 570/590 SLI for Intel, nForce 650i Ultra/650i SLI/680i LT SLI/680i SLI and nForce 750i SLI/780i SLI/790i SLI/790i Ultra SLI.
• VIA: P4M800, P4M800PRO, P4M890, P4M900, PT880 Pro/Ultra, PT890. (See also: List of VIA chipsets)
• SiS: 662, 671, 671fx, 672, 672fx
• ATI: Radeon Xpress 200 and CrossFire Xpress 3200 for Intel

The Yorkfield XE model QX9770 (45 nm with 1600 MT/s FSB) has limited chipset compatibility - with only X38, P35 (With Overclocking) and some high-performance X48 and P45 motherboards being compatible. BIOS updates were gradually being released to provide support for the Penryn technology, and the QX9775 is only compatible with the Intel D5400XS motherboard. The Wolfdale-3M model E7200 also has limited compatibility (at least the Xpress 200 chipset is incompatible)^{[citation needed]}.

Although a motherboard may have the required chipset to support Conroe, some motherboards based on the above-mentioned chipsets do not support Conroe. This is because all Conroe-based processors require a new power delivery feature set specified in Voltage Regulator-Down (VRD) 11.0. This requirement is a result of Conroe's significantly lower power consumption, compared to the Pentium 4/D CPUs it replaced. A motherboard that has both a supporting chipset and VRD 11 supports Conroe processors, but even then some boards will need an updated BIOS to recognize Conroe's FID (Frequency ID) and VID (Voltage ID).

Synchronous memory modules

Unlike the prior Pentium 4 and Pentium D design, the Core 2 technology sees a greater benefit from memory running synchronously with the front-side bus (FSB). This means that for the Conroe CPUs with FSB of 1066 MT/s, the ideal memory performance for DDR2 is PC2-8500. In a few configurations, using PC2-5300 instead of PC2-4200 can actually decrease performance. Only when going to PC2-6400 is there a significant performance increase. While DDR2 memory models with tighter timing specifications do improve performance, the difference in real world games and applications is often negligible.^[18]

Optimally, the memory bandwidth afforded should match the bandwidth of the FSB, that is to say that a CPU with a 533 MT/s rated bus speed should be paired with RAM matching the same rated speed, for example DDR2 533, or PC2-4200. A common myth^{[citation needed]} is that installing interleaved RAM will offer double the bandwidth. However, at most the increase in bandwidth by installing interleaved RAM is roughly 5–10%. The AGTL+ PSB used by all NetBurst processors and current and medium-term (pre-QuickPath) Core 2 processors provide a 64-bit data path. Current chipsets provide for a couple of either DDR2 or DDR3 channels.

On jobs requiring large amounts of memory access, the quad-core Core 2 processors can benefit significantly^[19] from using PC2-8500 memory, which runs at the same speed as the CPU's FSB; this is not an officially supported configuration, but several motherboards support it.

The Core 2 processor does not require the use of DDR2. While the Intel 975X and P965 chipsets require this memory, some motherboards and chipsets support both Core 2 processors and DDR memory. When using DDR memory, performance may be reduced because of the lower available memory bandwidth.

Chip errata

The Core 2 memory management unit (MMU) in X6800, E6000 and E4000 processors does not operate to prior specifications implemented in prior generations of x86 hardware. This may cause problems, many of them serious security and stability issues, with extant operating system software. Intel's documentation states that their programming manuals will be updated "in the coming months" with information on recommended methods of managing the translation lookaside buffer (TLB) for Core 2 to avoid issues, and admits that, "in rare instances, improper TLB invalidation may result in unpredictable system behavior, such as hangs or incorrect data."^[20]

Among the issues stated:

• Non-execute bit is shared across the cores.
• Floating point instruction non-coherencies.
• Allowed memory corruptions outside of the range of permitted writing for a process by running common instruction sequences.

Intel errata Ax39, Ax43, Ax65, Ax79, Ax90, Ax99 are said to be particularly serious.^[21] 39, 43, 79, which can cause unpredictable behavior or system hang, have been fixed in recent steppings.

Among those who have stated the errata to be particularly serious are

Microsoft has issued update KB936357 to address the errata by microcode update,^[25] with no performance penalty. BIOS updates are also available to fix the issue.

See also

• x86
• List of Intel CPU microarchitectures

References