Hydrogen storage

Source: Wikipedia, the free encyclopedia.
Not to be confused with green hydrogen for energy storage.
Liquid hydrogen Tank at NASA Kennedy Space Center

Several methods exist for storing

cryogenic liquid, and transported as such in cylinders, tubes, and cryogenic tanks for use in industry or as propellant in space programs. The overarching challenge is the very low boiling point of H2: it boils around 20.268 K
(−252.882 °C or −423.188 °F). Achieving such low temperatures requires expending significant energy.

Although molecular hydrogen has very high energy density on a mass basis, partly because of its low

molecular weight, as a gas at ambient conditions it has very low energy density by volume. If it is to be used as fuel stored on board a vehicle, pure hydrogen gas must be stored in an energy-dense form to provide sufficient driving range. Because hydrogen is the smallest molecule, it easily escapes from containers. Considering leakages, transport and production costs, hydrogen could have a Global Warming Potential (GWP100) of 11.6. Methane, for comparison, has a GWP of 34.[1]


Established technologies

Net storage density of hydrogen

Compressed hydrogen

Compressed hydrogen is a storage form whereby hydrogen gas is kept under pressures to increase the storage density. Compressed hydrogen in hydrogen tanks at 350 bar (5,000 psi) and 700 bar (10,000 psi) are used for hydrogen tank systems in vehicles, based on type IV carbon-composite technology.[2] Car manufacturers including Honda[3] and Nissan[4] have been developing this solution.

Liquefied hydrogen

Liquid hydrogen tanks for cars, producing for example the BMW Hydrogen 7. Japan has a liquid hydrogen (LH2) storage site in Kobe port.[5] Hydrogen is liquefied by reducing its temperature to −253 °C, similar to liquefied natural gas (LNG) which is stored at −162 °C. A potential efficiency loss of only 12.79% can be achieved, or 4.26 kW⋅h/kg out of 33.3 kW⋅h/kg.[6]

Chemical storage

Hydrogen gravimetric capacity of proposed storage materials for hydrogen fuel as a function of hydrogen release temperature. The targets have since been lowered.[7]

Chemical storage could offer high storage performance due to the high storage densities. For example, supercritical hydrogen at 30 °C and 500 bar only has a density of 15.0 mol/L while methanol has a hydrogen density of 49.5 mol H2/L methanol and saturated dimethyl ether at 30 °C and 7 bar has a density of 42.1 mol H2/L dimethyl ether.[citation needed]

Regeneration of storage material is problematic. A large number of chemical storage systems have been investigated. H2 release can be induced by

boron hydrides, ammonia, and alane etc.[8] A most promising chemical approach is electrochemical hydrogen storage, as the release of hydrogen can be controlled by the applied electricity.[9]
Most of the materials listed below can be directly used for electrochemical hydrogen storage.

As shown before,

nanomaterials offer advantage for hydrogen storage systems. Nanomaterials offer an alternative that overcomes the two major barriers of bulk materials, rate of sorption and release temperature.[citation needed
]

Enhancement of sorption kinetics and storage capacity can be improved through nanomaterial-based catalyst doping, as shown in the work of the Clean Energy Research Center in the University of South Florida.[10] This research group studied LiBH4 doped with nickel nanoparticles and analyzed the weight loss and release temperature of the different species. They observed that an increasing amount of nanocatalyst lowers the release temperature by approximately 20 °C and increases the weight loss of the material by 2-3%. The optimum amount of Ni particles was found to be 3 mol%, for which the temperature was within the limits established (around 100 °C) and the weight loss was notably greater than the undoped species.

The rate of hydrogen sorption improves at the nanoscale due to the short diffusion distance in comparison to bulk materials. They also have favorable surface-area-to-volume ratio.

The release temperature of a material is defined as the temperature at which the

van ’t Hoff equation
, relates temperature and partial pressure of hydrogen during the desorption process. The modifications to the standard equation are related to size effects at the nanoscale.

Where pH2 is the partial pressure of hydrogen, ΔH is the

surface free energy
of the particle.

From the above relation we see that the enthalpy and entropy change of desorption processes depend on the radius of the nanoparticle. Moreover, a new term is included that takes into account the specific surface area of the particle and it can be mathematically proven that a decrease in particle radius leads to a decrease in the release temperature for a given partial pressure.[12]

Hydrogenation of CO2

Current approach to reduce CO2 includes capturing and storing from facilities across the world. However, storage poses technical and economic barriers preventing global scale application. To utilize CO2 at the point source, CO2 hydrogenation is a realistic and practical approach. Conventional hydrogenation reduces unsaturated organic compounds by addition of H2. One method of CO2 hydrogenation is via the methanol pathway. Methanol can be used to produce long chain hydrocarbons. Some barriers of CO2 hydrogenation includes purification of captured CO2, H2 source from splitting water and energy inputs for hydrogenation. To overcome these barriers, we can further develop green H2 technology and encourage catalyst research at industrial and academic level. For industrial applications, CO2 is often converted to methanol. Until now, much progress has been made for CO2 to C1 molecules. However, CO2 to high value molecules still face many roadblocks and the future of CO2 hydrogenation depends on the advancement of catalytic technologies.[13]

Metal hydrides

Metal hydride hydrogen storage

Metal hydrides, such as MgH2, NaAlH4, LiAlH4, LiH, LaNi5H6, TiFeH2, ammonia borane, and palladium hydride represent sources of stored hydrogen. Again the persistent problems are the % weight of H2 that they carry and the reversibility of the storage process.[14] Some are easy-to-fuel liquids at ambient temperature and pressure, whereas others are solids which could be turned into pellets. These materials have good energy density, although their specific energy is often worse than the leading hydrocarbon
fuels.

LiNH2, LiBH4, and NaBH4.[15]

An alternative method for lowering dissociation temperatures is doping with activators. This strategy has been used for aluminium hydride, but the complex synthesis makes the approach unattractive.[16]

Proposed hydrides for use in a hydrogen economy include simple hydrides of magnesium[17] or transition metals and complex metal hydrides, typically containing sodium, lithium, or calcium and aluminium or boron. Hydrides chosen for storage applications provide low reactivity (high safety) and high hydrogen storage densities. Leading candidates are lithium hydride, sodium borohydride, lithium aluminium hydride and ammonia borane. A French company McPhy Energy is developing the first industrial product, based on magnesium hydride, already sold to some major clients such as Iwatani and ENEL.

Reversible hydrogen storage is exhibited by frustrated Lewis pair, which produces a borohydride.[18][19][20]

Phosphino borane hydrogenstorage
Phosphino borane hydrogenstorage

The phosphino-borane on the left accepts one equivalent of hydrogen at one atmosphere and 25 °C and expels it again by heating to 100 °C. The storage capacity is 0.25 wt%.

Aluminium

Main article: Aluminium

Hydrogen can be produced using aluminium by reacting it with water.[21] It was previously believed that, to react with water, aluminium must be stripped of its natural oxide layer using caustic substances, alloys,[22] or mixing with gallium (which produces aluminium nanoparticles that allow 90% of the aluminium to react).[23] It has since been demonstrated that efficient reaction is possible by increasing the temperature and pressure of the reaction.[24] The byproduct of the reaction to create hydrogen is aluminium oxide, which can be recycled back into aluminium with the Hall–Héroult process, making the reaction theoretically renewable. Although this requires electrolysis, which consumes a large amount of energy, the energy is then stored in the aluminium (and released when the aluminium is reacted with water).

Magnesium

Mg-based hydrogen storage materials can be generally fell into three categories, i.e., pure Mg, Mg-based alloys, and Mg-based composites. Particularly, more than 300 sorts of Mg-based hydrogen storage alloys have been receiving extensive attention[25] because of the relatively better overall performance. Nonetheless, the inferior hydrogen absorption/desorption kinetics rooting in the overly undue thermodynamic stability of metal hydride make the Mg-based hydrogen storage alloys currently not appropriate for the real applications, and therefore, massive attempts have been dedicated to overcoming these shortages. Some sample preparation methods, such as smelting, powder sintering, diffusion, mechanical alloying, hydriding combustion synthesis method, surface treatment, and heat treatment, etc., have been broadly employed for altering the dynamic performance and cycle life of Mg-based hydrogen storage alloys. Besides, some intrinsic modification strategies, including alloying,[26][27][28][29] nanostructuring,[30][31][32] doping by catalytic additives,[33][34] and acquiring nanocomposites with other hydrides,[35][36] etc., have been mainly explored for intrinsically boosting the performance of Mg-based hydrogen storage alloys.[37] Like aluminium, magnesium also reacts with water to produce hydrogen.[38]

Of the primary hydrogen storage alloys progressed formerly, Mg and Mg-based hydrogen storage materials are believed to provide the remarkable possibility of the practical application, on account of the advantages as following: 1) the resource of Mg is plentiful and economical. Mg element exists abundantly and accounts for ≈2.35% of the earth's crust with the rank of the eighth; 2) low density of merely 1.74 g cm-3; 3) superior hydrogen storage capacity. The theoretical hydrogen storage amounts of the pure Mg is 7.6 wt % (weight percent),[39][40][41] and the Mg2Ni is 3.6 wt%, respectively.[37]

Alanates-based systems

Lithium alanate (LiAlH4) was synthesized for the first time in 1947 by dissolution of lithium hydride in an ether solution of aluminium chloride.[42] LiAlH4 has a theoretical gravimetric capacity of 10.5 wt %H2 and dehydrogenates in the following three steps:[43][44][45] 3LiAlH4 ↔ Li3AlH6 + 3H2 + 2Al (423–448 K; 5.3 wt %H2; ∆H = −10 kJ·mol−1 H2); Li3AlH6 ↔ 3LiH + Al + 1.5H2 (453–493 K; 2.6 wt %H2; ∆H = 25 kJ·mol−1 H2); 3LiH + 3Al ↔ 3LiAl + 3/2H2 (>673 K; 2.6 wt %H2; ∆H = 140 kJ·mol−1 H2).[46] The first two steps lead to a total amount of hydrogen released equal to 7.9 wt %, which could be attractive for practical applications, but the working temperatures and the desorption kinetics are still far from the practical targets. Several strategies have been applied in the last few years to overcome these limits, such as ball-milling and catalysts additions.[47][48][49][50][51][46]

Potassium Alanate (KAlH4) was first prepared by Ashby et al.[52] by one-step synthesis in toluene, tetrahydrofuran, and diglyme. Concerning the hydrogen absorption and desorption properties, this alanate was only scarcely studied. Morioka et al.,[53] by temperature programmed desorption (TPD) analyses, proposed the following dehydrogenation mechanism: 3KAlH4 →K3AlH6 + 2Al + 3H2 (573 K, ∆H = 55 kJ·mol−1 H2; 2.9 wt %H2), K3AlH6 → 3KH + Al + 3/2H2 (613 K, ∆H = 70 kJ·mol−1 H2; 1.4 wt %H2), 3KH → 3K + 3/2H2 (703 K, 1.4 wt %H2). These reactions were demonstrated reversible without catalysts addition at relatively low hydrogen pressure and temperatures. The addition of TiCl3 was found to decrease the working temperature of the first dehydrogenation step of 50 K,[54] but no variations were recorded for the last two reaction steps.[46]

Organic hydrogen carriers

Main article: Liquid organic hydrogen carriers
Reversible hydrogenation of N-ethylcarbazole.

Unsaturated organic compounds can store huge amounts of hydrogen. These Liquid Organic Hydrogen Carriers (LOHC) are hydrogenated for storage and dehydrogenated again when the energy/hydrogen is needed. Using LOHCs, relatively high gravimetric storage densities can be reached (about 6 wt-%) and the overall

energy efficiency is higher than for other chemical storage options such as producing methane from the hydrogen.[55] Both hydrogenation and dehydrogenation of LOHCs requires catalysts.[56]
It was demonstrated that replacing hydrocarbons by hetero-atoms, like N, O etc. improves reversible de/hydrogenation properties.

Cycloalkanes

Research on LOHC was concentrated on cycloalkanes at an early stage, with its relatively high hydrogen capacity (6-8 wt %) and production of COx-free hydrogen.

Heterocyclic aromatic compounds (or N-Heterocycles) are also appropriate for this task. A compound featuring in LOHC research is N-Ethylcarbazole [de] (NEC)[57] but many others do exist.[58] Dibenzyltoluene, which is already used as a heat transfer fluid in industry, was identified as potential LOHC. With a wide liquid range between -39 °C (melting point) and 390 °C (boiling point) and a hydrogen storage density of 6.2 wt% dibenzyltoluene is ideally suited as LOHC material.[59] Formic acid has been suggested as a promising hydrogen storage material with a 4.4wt% hydrogen capacity.[60]

Cycloalkanes reported as LOHC include cyclohexane, methyl-cyclohexane and decalin. The dehydrogenation of cycloalkanes is highly endothermic (63-69 kJ/mol H2), which means this process requires high temperature.[56] Dehydrogenation of decalin is the most thermodynamically favored among the three cycloalkanes, and methyl-cyclohexane is second because of the presence of the methyl group.[61] Research on catalyst development for dehydrogenation of cycloalkanes has been carried out for decades. Nickel (Ni), Molybdenum (Mo) and Platinum (Pt) based catalysts are highly investigated for dehydrogenation. However, coking is still a big challenge for catalyst's long-term stability.[62][63]

N-Heterocycles

The temperature required for hydrogenation and dehydrogenation drops significantly for heterocycles vs simple carbocycles.[64] Among all the N-heterocycles, the saturated-unsaturated pair of dodecahydro-N-ethylcarbazole (12H-NEC) and NEC has been considered as a promising candidate for hydrogen storage with a fairly large hydrogen content (5.8wt%).[65] The figure on the top right shows dehydrogenation and hydrogenation of the 12H-NEC and NEC pair. The standard catalyst for NEC to 12H-NEC is Ru and Rh based. The selectivity of hydrogenation can reach 97% at 7 MPa and 130 °C-150 °C.[56] Although N-Heterocyles can optimize the unfavorable thermodynamic properties of cycloalkanes, a lot of issues remain unsolved, such as high cost, high toxicity and kinetic barriers etc.[56]

The imidazolium ionic liquids such alkyl(aryl)-3-methylimidazolium N-bis(trifluoromethanesulfonyl)imidate salts can reversibly add 6–12 hydrogen atoms in the presence of classical Pd/C or Ir0 nanoparticle catalysts and can be used as alternative materials for on-board hydrogen-storage devices. These salts can hold up to 30 g L−1 of hydrogen at atmospheric pressure.[66]

Formic acid

Formic acid is a highly effective hydrogen storage material, although its H2density is low. Carbon monoxide free hydrogen has been generated in a very wide pressure range (1–600 bar). A homogeneous catalytic system based on water-soluble ruthenium catalysts selectively decompose HCOOH into H2 and CO2 in aqueous solution.[67] This catalytic system overcomes the limitations of other catalysts (e.g. poor stability, limited catalytic lifetimes, formation of CO) for the decomposition of formic acid making it a viable hydrogen storage material.[68] And the co-product of this decomposition, carbon dioxide, can be used as hydrogen vector by hydrogenating it back to formic acid in a second step. The catalytic hydrogenation of CO2 has long been studied and efficient procedures have been developed.[69][70] Formic acid contains 53 g L−1 hydrogen at room temperature and atmospheric pressure. By weight, pure formic acid stores 4.3 wt% hydrogen. Pure formic acid is a liquid with a flash point 69 °C (cf. gasoline −40 °C, ethanol 13 °C). 85% formic acid is not flammable.

Ammonia and related compounds

Further information: Ammonia production

Ammonia

Ammonia (NH3) releases H2 in an appropriate catalytic reformer. Ammonia provides high hydrogen storage densities as a liquid with mild pressurization and cryogenic constraints: It can also be stored as a liquid at room temperature and pressure when mixed with water. Ammonia is the second most commonly produced chemical in the world and a large infrastructure for making, transporting, and distributing ammonia exists. Ammonia can be reformed to produce hydrogen with no harmful waste, or can mix with existing fuels and under the right conditions burn efficiently. Since there is no carbon in ammonia, no carbon by-products are produced; thereby making this possibility a "carbon neutral" option for the future. Pure ammonia burns poorly at the atmospheric pressures found in natural gas fired water heaters and stoves. Under compression in an automobile engine it is a suitable fuel for slightly modified gasoline engines. Ammonia is a suitable alternative fuel because it has 18.6 MJ/kg energy density at NTP and carbon-free combustion byproducts.[71]

Ammonia has several challenges to widespread adaption as a hydrogen storage material. Ammonia is a toxic gas with a potent odor at standard temperature and pressure.[72] Additionally, advances in the efficiency and scalability of ammonia decomposition are needed for commercial viability, as fuel cell membranes are highly sensitive to residual ammonia and current decomposition techniques have low yield rates.[73] A variety of transition metals can be used to catalyze the ammonia decomposition reaction, the most effective being ruthenium. This catalysis works through chemisorption, where the adsorption energy of N2 is less than the reaction energy of dissociation.[74] Hydrogen purification can be achieved in several ways. Hydrogen can be separated from unreacted ammonia using a permeable, hydrogen-selective membrane.[75] It can also be purified through the adsorption of ammonia, which can be selectively trapped due to its polarity.[76]

In September 2005 chemists from the Technical University of Denmark announced a method of storing hydrogen in the form of ammonia saturated into a salt tablet. They claim it will be an inexpensive and safe storage method.[77][needs update]

Positive attributes of Ammonia[citation needed]
  • High theoretical energy density
  • Wide spread availability
  • Large scale commercial production
  • Benign decomposition pathway to H2 and N2
Negative attributes of Ammonia[citation needed]
  • Toxicity
  • Corrosive
  • High decomposition temperature leading to efficiency loss

Hydrazine

Hydrazine breaks down in the cell to form nitrogen and hydrogen/[78] Silicon hydrides and germanium hydrides are also candidates of hydrogen storage materials, as they can subject to energetically favored reaction to form covalently bonded dimers with loss of a hydrogen molecule.[79][80]

Amine boranes

Main article:
Amine borane complex

Prior to 1980, several compounds were investigated for hydrogen storage including complex borohydrides, or aluminohydrides, and ammonium salts. These hydrides have an upper theoretical hydrogen yield limited to about 8.5% by weight. Amongst the compounds that contain only B, N, and H (both positive and negative ions), representative examples include: amine boranes, boron hydride ammoniates, hydrazine-borane complexes, and ammonium octahydrotriborates or tetrahydroborates. Of these, amine boranes (and especially ammonia borane) have been extensively investigated as hydrogen carriers. During the 1970s and 1980s, the U.S. Army and Navy funded efforts aimed at developing hydrogen/deuterium gas-generating compounds for use in the HF/DF and HCl chemical lasers, and gas dynamic lasers. Earlier hydrogen gas-generating formulations used amine boranes and their derivatives. Ignition of the amine borane(s) forms boron nitride (BN) and hydrogen gas. In addition to ammonia borane (H3BNH3), other gas-generators include diborane diammoniate, H2B(NH3)2BH4.[citation needed]

Physical storage

In this case hydrogen remains in physical forms, i.e., as gas, supercritical fluid, adsorbate, or molecular inclusions. Theoretical limitations and experimental results are considered[81] concerning the volumetric and gravimetric capacity of glass microvessels, microporous, and nanoporous media, as well as safety and refilling-time demands. Because hydrogen is the smallest molecule, it easily escapes from containers and during transfer from container to container, and leaked hydrogen has a global warming effect 11.6 times stronger than CO₂.[82]

Zeolites

Zeolites are microporous and highly crystalline aluminosilicate materials. As they exhibit cage and tunnel structures, they offer the potential for the encapsulation of non-polar gases such as H2. In this system, hydrogen is physisorbed on the surface of the zeolite pores through a mechanism of adsorption that involves hydrogen being forced into the pores under pressure and low temperature.[83] Therefore, similar to other porous materials, its hydrogen storage capacity depends on the BET surface area, pore volume, the interaction of molecular hydrogen with the internal surfaces of the micropores, and working conditions such as pressure and temperature.[84]

Research shows that the channel diameter is also one of the parameters determining this capacity, especially at high pressure. In this case, an effective material should exhibit a large pore volume and a channel diameter close to the kinetic diameter of the hydrogen molecule (dH=2.89 Å).[83]

Table below shows the hydrogen uptake of several zeolites at liquid nitrogen temperature (77K):

H2 uptake of several high surface area zeolites[85]
Zeolite Framework Type (IZA Code) Pressure (bar) H2 Uptake (wt%) BET Surface Area (m2/g)
NaY (Si/Al = 2.4) FAU 0.57 0.37
HY (Si/Al = 2.7) FAU 0.95 0.56
MCM-41 1 0.58 1017
H-ZSM-5 (Si/Al = 40) MFI 0.92 0.71 418
H-SAPO-34 CHA 0.92 1.09 547
H-CHA (Si/Al = 2.1) CHA 0.92 1.10 490
H-SSZ-13 (Si/Al = 11.6) CHA 0.92 1.28 638
NaA LTA 0.93 1.21
LiX (Si/Al = 1.4) FAU 0.60 0.88
NaX (Si/Al = 1.05) FAU 0.61 1.22
CaX (Si/Al = 1.4) FAU 1.01 1.25 669
Li-LSX (Si/Al = 1.0) FAU 1.01 1.50 717
Na-LSX (Si/Al = 1.0) FAU 1.01 1.46 642
K-LSX (Si/Al = 1.0) FAU 1.01 1.33 570

Porous or layered carbon

Activated carbons are highly porous amorphous carbon materials with high apparent surface area. Hydrogen physisorption can be increased in these materials by increasing the apparent surface area and optimizing pore diameter to around 7 Å.[86] These materials are of particular interest due to the fact that they can be made from waste materials, such as cigarette butts which have shown great potential as precursor materials for high-capacity hydrogen storage materials.[87][88]

Graphene can store hydrogen efficiently. The H2 adds to the double bonds giving graphane. The hydrogen is released upon heating to 450 °C.[89][90]

Carbon nanotubes

Hydrogen carriers based on nanostructured carbon (such as carbon buckyballs and nanotubes) have been proposed. However, hydrogen content amounts up to ≈3.0-7.0 wt% at 77K which is far from the value set by US Department of Energy (6 wt% at nearly ambient conditions).[citation needed]

To realize carbon materials as effective hydrogen storage technologies, carbon nanotubes (CNTs) have been doped with

CNTs within the MgH2 lattice. Fullerene substances are other carbonaceous nanomaterials that have been tested for hydrogen storage in this center. Fullerene molecules are composed of a C60 close-caged structure, that allows for hydrogenation of the double bonded carbons leading to a theoretical C60H60 isomer
with a hydrogen content of 7.7 wt%. However, the release temperature in these systems is high (600 °C).

Metal-organic frameworks

Metal-organic frameworks represent another class of synthetic porous materials that store hydrogen and energy at the molecular level. MOFs are highly crystalline inorganic-organic hybrid structures that contain metal clusters or ions (secondary building units) as nodes and organic ligands as linkers. When guest molecules (solvent) occupying the pores are removed during solvent exchange and heating under vacuum, porous structure of MOFs can be achieved without destabilizing the frame and hydrogen molecules will be adsorbed onto the surface of the pores by physisorption. Compared to traditional zeolites and porous carbon materials, MOFs have very high number of pores and surface area which allow higher hydrogen uptake in a given volume. Thus, research interests on hydrogen storage in MOFs have been growing since 2003 when the first MOF-based hydrogen storage was introduced. Since there are infinite geometric and chemical variations of MOFs based on different combinations of SBUs and linkers, many researches explore what combination will provide the maximum hydrogen uptake by varying materials of metal ions and linkers.[citation needed
]

Factors influencing hydrogen storage ability

Temperature, pressure and composition of MOFs can influence their hydrogen storage ability. The adsorption capacity of MOFs is lower at higher temperature and higher at lower temperatures. With the rising of temperature, physisorption decreases and chemisorption increases.[91] For MOF-519 and MOF-520, the isosteric heat of adsorption decreased with pressure increase.[92] For MOF-5, both gravimetric and volumetric hydrogen uptake increased with increase in pressure.[91] The total capacity may not be consistent with the usable capacity under pressure swing conditions. For instance, MOF-5 and IRMOF-20, which have the highest total volumetric capacity, show the least usable volumetric capacity.[93] Absorption capacity can be increased by modification of structure. For example, the hydrogen uptake of PCN-68 is higher than PCN-61.[94] Porous aromatic frameworks (PAF-1), which is known as a high surface area material, can achieve a higher surface area by doping.[95]

Modification of MOFs

There are many different ways to modify MOFs, such as MOF catalysts, MOF hybrids, MOF with metal centers and doping. MOF catalysts have high surface area, porosity and hydrogen storage capacity. However, the active metal centers are low. MOF hybrids have enhanced surface area, porosity, loading capacity and hydrogen storage capacity. Nevertheless, they are not stable and lack active centers. Doping in MOFs can increase hydrogen storage capacity, but there might be steric effect and inert metals have inadequate stability. There might be formation of interconnected pores and low corrosion resistance in MOFs with metal centers, while they might have good binding energy and enhanced stability. These advantages and disadvantages for different kinds of modified MOFs show that MOF hybrids are more promising because of the good controllability in selection of materials for high surface area, porosity and stability.[91]

In 2006, chemists achieved hydrogen storage concentrations of up to 7.5 wt% in MOF-74 at a low temperature of 77 K.[96][97] In 2009, researchers reached 10 wt% at 77 bar (1,117 psi) and 77 K with MOF NOTT-112.[98] Most articles about hydrogen storage in MOFs report hydrogen uptake capacity at a temperature of 77K and a pressure of 1 bar because these conditions are commonly available and the binding energy between hydrogen and the MOF at this temperature is large compared to the thermal vibration energy. Varying several factors such as surface area, pore size, catenation, ligand structure, and sample purity can result in different amounts of hydrogen uptake in MOFs.

In 2020, researchers reported that NU-1501-Al, an ultraporous metal–organic framework (MOF) based on metal trinuclear clusters, yielded "impressive gravimetric and volumetric storage performances for hydrogen and methane", with a hydrogen delivery capacity of 14.0% w/w, 46.2 g/litre.[99][100]

Cryo-compressed

Cryo-compressed storage of hydrogen is the only technology that meets 2015 DOE targets for volumetric and gravimetric efficiency (see "CcH2" on slide 6 in[101]).

Furthermore, another study has shown that cryo-compression exhibits interesting cost advantages: ownership cost (price per mile) and storage system cost (price per vehicle) are actually the lowest when compared to any other technology (see third row in slide 13 of[102]).

Like liquid storage, cryo-compressed uses cold hydrogen (20.3 K and slightly above) in order to reach a high energy density. However, the main difference is that, when the hydrogen would warm-up due to heat transfer with the environment ("boil off"), the tank is allowed to go to pressures much higher (up to 350 bars versus a couple of bars for liquid storage). As a consequence, it takes more time before the hydrogen has to vent, and in most driving situations, enough hydrogen is used by the car to keep the pressure well below the venting limit.[citation needed]

Consequently, it has been demonstrated that a high driving range could be achieved with a cryo-compressed tank : more than 650 miles (1,050 km) were driven with a full tank mounted on a hydrogen-fueled engine of Toyota Prius.[103] Research is still underway to study and demonstrate the full potential of the technology.[104]

As of 2010, the BMW Group has started a thorough component and system level validation of cryo-compressed vehicle storage on its way to a commercial product.[105]

Cryo-supercritical

Clathrate hydrates

H2 caged in a clathrate hydrate was first reported in 2002, but requires very high pressures to be stable. In 2004, researchers showed solid H2-containing hydrates could be formed at ambient temperature and tens of bars by adding small amounts of promoting substances such as THF.[106][107] These clathrates have a theoretical maximum hydrogen densities of around 5 wt% and 40 kg/m3.

Glass capillary arrays

A team of Russian, Israeli and German scientists have collaboratively developed an innovative technology based on glass capillary arrays for the safe infusion, storage and controlled release of hydrogen in mobile applications.[108][109] The C.En technology has achieved the United States Department of Energy (DOE) 2010 targets for on-board hydrogen storage systems.[110] DOE 2015 targets can be achieved using flexible glass capillaries and cryo-compressed method of hydrogen storage.[111]

Glass microspheres

Hollow

thermal conductivity; this hinders hydrogen diffusivity
, and subsequently a higher temperature is required to achieve the desired storage capacity.

To make this technology more economically viable for commercial use, research is being done to increase the

metal oxide began to cover pores in the glass shell. This study concluded with a hydrogen storage capacity of 3.31 wt% with 2 wt% Co at 200 °C and 10 bar.[112]

A study done by Rapp and Shelby sought to increase the hydrogen release rate through photo-induced outgassing in doped HGMs in comparison to conventional heating methods. The glass was doped with

infrared light. The study found that 0.5 wt% Fe3O4 doped 7070 borosilicate glass had hydrogen release increase proportionally to the infrared lamp intensity. In addition to the improvements to diffusivity by infrared alone, reactions between the hydrogen and iron-doped glass increased the Fe2+/Fe3+ ratio which increased infrared absorption therefore further increasing the hydrogen yield.[114]

As of 2020, the progress made in studying HGMs has increased its efficiency but it still falls short of Department of Energy targets for this technology. The operation temperatures for both hydrogen adsorption and release are the largest barrier to commercialization.[115]

Stationary hydrogen storage

Unlike mobile applications, hydrogen density is not a huge problem for stationary applications. As for mobile applications, stationary applications can use established technology:

Underground hydrogen storage

'Available storage technologies, their capacity and discharge time.'[117]: 12 

Underground hydrogen storage

CAES systems.[122] A German case study on storage of hydrogen in salt caverns found that if the German power surplus (7% of total variable renewable generation by 2025 and 20% by 2050) would be converted to hydrogen and stored underground, these quantities would require some 15 caverns of 500,000 cubic metres each by 2025 and some 60 caverns by 2050 – corresponding to approximately one third of the number of gas caverns currently operated in Germany.[123] In the US, Sandia Labs are conducting research into the storage of hydrogen in depleted oil and gas fields, which could easily absorb large amounts of renewably produced hydrogen as there are some 2.7 million depleted wells in existence.[124]

Underground hydrogen storage is the practice of hydrogen storage in

gas fields.[127][128] Large quantities of gaseous hydrogen have been stored in caverns for many years.[129] [failed verification – see discussion] [unreliable source?] The storage of large quantities of hydrogen underground in solution-mined salt domes,[130] aquifers,[131] excavated rock caverns, or mines can function as grid energy storage,[132] essential for the hydrogen economy.[133] By using a turboexpander the electricity needs for compressed storage on 200 bar amounts to 2.1% of the energy content.[134]

Salt caverns

The Chevron Phillips Clemens Terminal in Texas has stored hydrogen since the 1980s in a solution-mined salt cavern. The cavern roof is about 2,800 feet (850 m) underground. The cavern is a cylinder with a diameter of 160 feet (49 m), a height of 1,000 feet (300 m), and a usable hydrogen capacity of 1,066 million cubic feet (30.2×10^6 m3), or 2,520 metric tons (2,480 long tons; 2,780 short tons).[135]

Salt caverns are artificially created by injecting water from the surface into a well in the rock salt, where rock salt is a polycrystalline material made of NaCl, halite. Locations such as salt domes or bedded salt are usually picked for salt caverns’ creation. Salt caverns can reach a maximum depth of 2000 m and a maximum volume capacity of 1,000,000 m3. The frequency of injection and withdrawal cycles ranges between 10 and 12 cycles per year. And the leak rate is around 1%.[136][137]

Due to the physiochemical properties of the rock salt, salt caverns exhibit multiple advantages. Key characteristics are low water content, low porosity and permeability, and its chemical inertia towards hydrogen.[138] Permeability is a key parameter in underground hydrogen storage, which affects its ability to seal. Though studies have found dilatancy and extensional fracture can cause significant permeability increase, rock salt crystal's recrystallization, which is a grain boundaries healing process, may contribute to its mechanical stiffness and permeability recovery.[139] Its plastic properties prevent the formation and spread of fractures and protect it from losing its tightness, which is particularly important for hydrogen storage.[138] Some of the disadvantages of salt caverns include lower storage capacity, large amount of water needed, and the effect of corrosion. Cushion gas is needed to avoid creep due to pressure drop when withdrawing gas from the reservoir. Though the need for cushion gas is relatively small, around 20%, the operational cost can still add up when working with a larger storage capacity. Cost is another big concern, where the cost of construction and operation are still high.[137][140]

Though people have experience with storing natural gas, storing hydrogen is a lot more complex. Factors such as hydrogen diffusivity in solids cause restrictions in salt cavern storage. Microbial activity is under extensive research worldwide because of its impact on hydrogen loss. As a result of methanogenic bacteria's bacterial metabolism, carbon dioxide and hydrogen are consumed and methane is produced, which leads to the loss of hydrogen stored in the salt caverns.[141][140]

Development

  • Sandia National Laboratories released in 2011 a life-cycle cost analysis framework for geologic storage of hydrogen.[142]
  • The European project Hyunder
    compressed air energy storage systems.[144]
  • ETI released in 2015 a report The role of hydrogen storage in a clean responsive power system noting that the UK has sufficient salt bed resources to provide tens of GWe.[145]
  • RAG Austria AG finished a hydrogen storage project in a depleted oil and gas field in Austria in 2017, and is conducting its second project "Underground Sun Conversion".[146]

A cavern sized 800 m tall and 50 m diameter can hold hydrogen equivalent to 150 GWh.[147][148]

Power to gas

biomethanation,[149][150] where biomethanogens (archaea) consume carbon dioxide and hydrogen and produce methane within an anaerobic
environment. This process is highly efficient, as the archaea are self-replicating and only require low-grade (60 °C) heat to perform the reaction.

Another process has also been achieved by

SoCalGas to convert the carbon dioxide in raw biogas to methane in a single electrochemical step, representing a simpler method of converting excess renewable electricity into storable natural gas.[151]

The UK has completed surveys and is preparing to start injecting hydrogen into the gas grid as the grid previously carried 'town gas' which is a 50% hydrogen-methane gas formed from coal. Auditors KPMG found that converting the UK to hydrogen gas could be £150bn to £200bn cheaper than rewiring British homes to use electric heating powered by lower-carbon sources.[152]

Excess power or off peak power generated by wind generators or solar arrays can then be used for load balancing in the energy grid. Using the existing natural gas system for hydrogen, Fuel cell maker

power to gas system in Canada.[153]

towngas, which for the most part (60-65%) consisted of hydrogen. The storage capacity of the German natural gas network is more than 200,000 GW·h which is enough for several months of energy requirement. By comparison, the capacity of all German pumped storage power plants amounts to only about 40 GW·h. The transport of energy through a gas network is done with much less loss (<0.1%) than in a power network (8%). The use of the existing natural gas pipelines for hydrogen was studied by NaturalHy[154]

Automotive onboard hydrogen storage

Portability is one of the biggest challenges in the automotive industry, where high density storage systems are problematic due to safety concerns. High-pressure tanks weigh much more than the hydrogen they can hold. For example, in the 2014 Toyota Mirai, a full tank contains only 5.7% hydrogen, the rest of the weight being the tank.[155]

System densities are often around half those of the working material, thus while a material may store 6 wt% H2, a working system using that material may only achieve 3 wt% when the weight of tanks, temperature and pressure control equipment, etc., is considered.[citation needed]

Fuel cells and storage

Due to its clean-burning characteristics, hydrogen is a clean fuel alternative for the automotive industry. Hydrogen-based fuel could significantly reduce the emissions of greenhouse gases such as CO2, SO2 and NOx. Three problems for the use of hydrogen fuel cells (HFC) are efficiency, size, and safe onboard storage of the gas. Other major disadvantages of this emerging technology involve cost, operability and durability issues, which still need to be improved from the existing systems. To address these challenges, the use of nanomaterials has been proposed as an alternative option to the traditional hydrogen storage systems. The use of nanomaterials could provide a higher density system and increase the driving range towards the target set by the DOE at 300 miles. Carbonaceous materials such as carbon nanotube and metal hydrides are the main focus of research. They are currently being considered for onboard storage systems due to their versatility, multi-functionality, mechanical properties and low cost with respect to other alternatives.[156]

Other advantages of nanomaterials in fuel cells

The introduction of nanomaterials in onboard hydrogen storage systems may be a major turning point in the automotive industry. However, storage is not the only aspect of the fuel cell to which nanomaterials may contribute. Different studies have shown that the transport and

SnO2 nanoparticles.[156] The increased performance is caused by an improvement in hydrogen splitting kinetics due to catalytic activity of the nanoparticles. Furthermore, this system exhibits faster transport of protons across the cell which makes HFCs
with nanoparticle composite membranes a promising alternative.

Another application of nanomaterials in water splitting has been introduced by a research group at

electrodes consisting of a graphene-like material.[157] Similar systems have been developed using photoelectrochemical techniques
.

Pressurized hydrogen gas

See also: Compressed hydrogen

Increasing gas pressure improves the energy density by volume making for smaller container tanks. The standard material for holding pressurised hydrogen in tube trailers is steel (there is no hydrogen embrittlement problem with hydrogen gas). Tanks made of carbon and glass fibres reinforcing plastic as fitted in Toyota Marai and Kenworth trucks are required to meet safety standards. Few materials are suitable for tanks as hydrogen being a small molecule tends to diffuse through many polymeric materials. The most common on board hydrogen storage in 2020 vehicles was hydrogen at pressure 700bar = 70MPa. The energy cost of compressing hydrogen to this pressure is significant.[citation needed]

Pressurized gas pipelines
are always made of steel and operate at much lower pressures than tube trailers.

Liquid hydrogen

See also: Liquid hydrogen

Alternatively, higher volumetric energy density liquid hydrogen or

liquification energies. The liquefaction process, involving pressurizing and cooling steps, is energy intensive.[158] The liquefied hydrogen has lower energy density by volume than gasoline by approximately a factor of four, because of the low density of liquid hydrogen – there are actually more oxidizable hydrogen atoms in a litre of gasoline (116 grams) than there are in a litre of pure liquid hydrogen (71 grams). Like any other liquid at cryogenic temperatures
, the liquid hydrogen storage tanks must also be well insulated to minimize boil off.

Japan has a liquid hydrogen (LH2) storage facility at a terminal in Kobe, and was expected to receive the first shipment of liquid hydrogen via LH2 carrier in 2020.[159] Hydrogen is liquified by reducing its temperature to −253 °C, similar to liquified natural gas (LNG) which is stored at −162 °C. A potential efficiency loss of 12.79% can be achieved, or 4.26kWh/kg out of 33.3kWh/kg.[160]

Liquid organic hydrogen carriers (LOHC)

Main article: Liquid organic hydrogen carriers

Underground hydrogen storage

Underground hydrogen storage is the practice of hydrogen storage in caverns, salt domes and depleted oil and gas fields. Large quantities of gaseous hydrogen have been stored in caverns by ICI for many years without any difficulties.[161] The storage of large quantities of liquid hydrogen underground can function as grid energy storage. The round-trip efficiency is approximately 40% (vs. 75–80% for pumped-hydro (PHES)), and the cost is slightly higher than pumped hydro.[162]

Another study referenced by a European staff working paper found that for large scale storage, the cheapest option is hydrogen at €140/MWh for 2,000 hours of storage using an electrolyser, salt cavern storage and combined-cycle power plant.

CAES systems.[165]

A German case study on storage of hydrogen in salt caverns found that if the German power surplus (7% of total variable renewable generation by 2025 and 20% by 2050) would be converted to hydrogen and stored underground, these quantities would require some 15 caverns of 500,000 cubic metres each by 2025 and some 60 caverns by 2050 – corresponding to approximately one third of the number of gas caverns currently operated in Germany.[166] In the US, Sandia Labs are conducting research into the storage of hydrogen in depleted oil and gas fields, which could easily absorb large amounts of renewably produced hydrogen as there are some 2.7 million depleted wells in existence.[167]

Research

The Hydrogen Storage Materials research field is vast, having tens of thousands of published papers.[168] According to Papers in the 2000 to 2015 period collected from Web of Science and processed in VantagePoint® bibliometric software, a scientometric review of research in hydrogen storage materials was constituted. According to the literature, hydrogen energy went through a hype-cycle type of development in the 2000s. Research in Hydrogen Storage Materials grew at increasing rates from 2000 to 2010. Afterwards, growth continued but at decreasing rates, and a plateau was reached in 2015. Looking at individual country output, there is a division between countries that after 2010 inflected to a constant or slightly declining production, such as the European Union countries, the US and Japan, and those whose production continued growing until 2015, such as China and South Korea. The countries with most publications were China, the EU and the United States, followed by Japan. China kept the leading position throughout the entire period, and had a higher share of hydrogen storage materials publications in its total research output.[169]

Among materials classes, Metal-Organic Frameworks were the most researched materials, followed by Simple Hydrides. Three typical behaviors were identified:

  1. New materials, researched mainly after 2004, such as MOFs and Borohydrides;
  2. Classic materials, present through the entire period with growing number of papers, such as Simple Hydrides, and
  3. Materials with stagnant or declining research through the end of the period, such as AB5 alloys and Carbon Nanotubes.[169]

However, current physisorption technologies are still far from being commercialized. The experimental studies are executed for small samples less than 100 g.[170] The described technologies require high pressure and/or low temperatures as a rule. Therefore, at their current state of the art these techniques are not considered as a separate novel technology but as a type of valuable add-on to current compression and liquefaction methods.

Physisorption processes are reversible since no activation energy is involved and the interaction energy is very low. In materials such as metal–organic frameworks, porous carbons, zeolites, clathrates, and organic polymers, hydrogen is physisorbed on the surface of the pores. In these classes of materials, the hydrogen storage capacity mainly depends on the surface area and pore volume. The main limitation of use of these sorbents as H2storage materials is weak van der Waals interaction energy between hydrogen and the surface of the sorbents. Therefore, many of the physisorption based materials have high storage capacities at liquid nitrogen temperature and high pressures, but their capacities become very low at ambient temperature and pressure.[citation needed]

obsolete source
]

See also

References

  1. doi:10.1038/s43247-023-00857-8
    . Retrieved 2024-04-11.
  2. doi:10.1039/C2EE22596D. Archived
    from the original on 2014-02-09. Retrieved 2014-12-19.
  3. ^ "FCX Clarity". Honda Worldwide. Archived from the original on 2011-12-09. Retrieved 2012-01-08.
  4. ^ "X-TRAIL FCV '03 model". Nissan-global.com. Archived from the original on 2010-09-17. Retrieved 2012-01-08.
  5. ^ Savvides, Nick (2017-01-11). "Japan plans to use imported liquefied hydrogen to fuel Tokyo 2020 Olympics". Fairplay. IHS Markit Maritime Portal. Archived from the original on 2018-04-23. Retrieved 22 April 2018.
  6. doi:10.1016/j.ijhydene.2017.01.136
    .
  7. ^ "Target Explanation Document: Onboard Hydrogen Storage forLight-Duty Fuel Cell Vehicles" (PDF). US Department of Energy. Archived (PDF) from the original on Apr 11, 2021.
  8. doi:10.1016/j.cattod.2006.09.022. Archived
    from the original on 2019-10-21. Retrieved 2019-06-27.
  9. doi:10.1016/j.ijhydene.2017.08.103
    .
  10. ^
    doi:10.1155/2008/950967
    .
  11. ^ EU Hydrogen Storage Archived 2012-10-25 at the Wayback Machine. (PDF)
  12. S2CID 118701455
    .
  13. ISSN 0021-9517. Archived
    from the original on 2022-10-16. Retrieved 2021-11-19.
  14. ^ DOE Metal hydrides Archived 2008-01-31 at the Wayback Machine. eere.energy.gov (2008-12-19)
  15. PMID 22873406
    .
  16. doi:10.2172/899889. Archived
    from the original on 2019-10-21. Retrieved 2019-06-27.
  17. ^ CNRS Institut Neel H2 Storage Archived 2016-03-03 at the Wayback Machine. Neel.cnrs.fr
  18. S2CID 20333088
    .
  19. ^ Elizabeth Wilson H2 Activation, Reversibly Metal-free compound readily breaks and makes hydrogen Archived 2006-11-27 at the Wayback Machine, Chemical & Engineering News November 20, 2006
  20. tris(pentafluorophenyl)boron
  21. ^ White Paper: A Novel Method For Grid Energy Storage Using Aluminium Fuel Archived 2013-05-31 at the Wayback Machine, Alchemy Research, April 2012.
  22. ^ "New process generates hydrogen from aluminium alloy to run engines, fuel cells". phys.org.
  23. ^ Blain, Loz (2022-09-02). "Aluminum-gallium powder bubbles hydrogen out of dirty water". New Atlas. Archived from the original on 2022-09-04. Retrieved 2022-09-04.
  24. S2CID 225254629. Archived
    from the original on 2022-10-16. Retrieved 2022-09-06.
  25. S2CID 98790485. Archived
    from the original on 2022-10-16. Retrieved 2021-11-20.
  26. ISSN 1359-6454
    .
  27. ISSN 0360-3199
    .
  28. ISSN 0925-8388
    .
  29. ISSN 0925-8388. Archived
    from the original on 2012-03-30. Retrieved 2021-11-20.
  30. PMID 17488082
    .
  31. PMID 19883120
    .
  32. PMID 20890496. Archived
    from the original on 2021-11-20. Retrieved 2021-11-20.
  33. S2CID 197614310
    .
  34. S2CID 139886102
    .
  35. ISSN 0360-3199
    .
  36. S2CID 202212456
    .
  37. ^
    S2CID 216182360. Archived
    from the original on 2022-06-15. Retrieved 2021-11-20.
  38. ISSN 0021-8979. Archived
    from the original on 2022-08-02. Retrieved 2022-09-06.
  39. ISSN 0277-5387
    .
  40. ^ "Scopus preview - Scopus - Welcome to Scopus". www.scopus.com. Archived from the original on 2019-09-06. Retrieved 2021-11-19.
  41. ISSN 2211-2855. Archived
    from the original on 2012-11-07. Retrieved 2021-11-20.
  42. PMID 14577773
    .
  43. ISSN 0020-1669
    .
  44. ISSN 0360-3199. Archived
    from the original on 2022-10-16. Retrieved 2021-11-20.
  45. ISSN 0025-5408
    .
  46. ^
    ISSN 2075-4701. Text was copied from this source, which is available under a Creative Commons Attribution 4.0 International License Archived 2017-10-16 at the Wayback Machine
    .
  47. ISSN 0925-8388. Archived
    from the original on 2022-10-16. Retrieved 2021-11-20.
  48. ISSN 0360-3199. Archived
    from the original on 2022-10-16. Retrieved 2021-11-20.
  49. ISSN 0360-3199. Archived
    from the original on 2022-10-16. Retrieved 2021-11-20.
  50. ISSN 0360-3199. Archived
    from the original on 2022-10-16. Retrieved 2021-11-20.
  51. ISSN 0360-3199. Archived
    from the original on 2022-10-16. Retrieved 2021-11-20.
  52. ISSN 0020-1669
    .
  53. ISSN 0925-8388. Archived
    from the original on 2022-10-16. Retrieved 2021-11-20.
  54. S2CID 93043691
    .
  55. doi:10.1002/cite.201100113
    .
  56. ^
    doi:10.1016/j.jechem.2015.08.007. Archived
    from the original on 2021-03-09. Retrieved 2019-11-29.
  57. doi:10.1039/C1EE01454D
    .
  58. ^ US patent 7351395, "Hydrogen storage by reversible hydrogenation of pi-conjugated substrates" 
  59. PMID 23956191
    .
  60. doi:10.1039/C2EE21928J
    .
  61. doi:10.1016/j.jcat.2007.11.012
    .
  62. doi:10.1016/S0926-860X(02)00139-4
    .
  63. doi:10.1016/j.cattod.2008.07.020
    .
  64. PMID 17534500
    .
  65. doi:10.1039/C2EE22066K
    .
  66. doi:10.1021/ef060481t
    .
  67. PMID 18393267
    .
  68. PMID 18781551
    .
  69. ^ P. G. Jessop, in Handbook of Homogeneous Hydrogenation (Eds.: J. G. de Vries, C. J. Elsevier), Wiley-VCH, Weinheim, Germany, 2007, pp. 489–511.
  70. doi:10.1016/j.ccr.2004.05.019
    .
  71. ISSN 0360-3199
    .
  72. ^ The ammonia economy Archived 2008-05-13 at the Wayback Machine. Memagazine.org (2003-07-10)
  73. S2CID 104446684
    .
  74. ISSN 0021-9517. Archived
    from the original on 2020-07-16. Retrieved 2020-11-18.
  75. ISSN 0376-7388
    .
  76. PMID 15975585
    .
  77. ^ Focus Denmark Archived 2007-09-27 at the Wayback Machine. Netpublikationer.dk (2006-06-13)
  78. ^ "Liquid asset". The Engineer. 2008-01-15. Archived from the original on 2012-12-09. Retrieved 2015-01-09.
  79. ^ Zong, J., J. T. Mague, and R. A. Pascal, Jr., Exceptional Steric Congestion in an in,in-Bis(hydrosilane), J. Am. Chem. Soc. 2013, 135, 13235-13237.
  80. doi:10.1002/qua.25432
    .
  81. doi:10.1016/B978-1-78242-362-1.00008-0
  82. ^ Bjørnæs, Christian. "Global warming potential of hydrogen estimated", Centre for International Climate and Environmental Research, June 7, 2023. Retrieved June 15, 2023.
  83. ^
    ISSN 0360-3199
    .
  84. ISSN 0360-3199
    .
  85. PMID 16928014
    .
  86. ISSN 1754-5706
    .
  87. PMID 29146978
    .
  88. S2CID 104050734. Archived
    (PDF) from the original on 2019-04-28. Retrieved 2019-06-27.
  89. ^ Graphene as suitable hydrogen storage substance Archived 2008-12-05 at the Wayback Machine. Physicsworld.com
  90. ^ Graphene to graphane Archived 2011-06-08 at the Wayback Machine. Rsc.org. January 2009
  91. ^
    S2CID 233623695. Archived
    from the original on 2022-10-16. Retrieved 2021-11-21.
  92. ISSN 0927-0256. Archived
    from the original on 2022-10-16. Retrieved 2021-11-21.
  93. PMID 30952862. Archived
    from the original on 2022-10-16. Retrieved 2021-11-21.
  94. ISSN 0040-4039. Archived
    from the original on 2022-10-16. Retrieved 2021-11-21.
  95. S2CID 104093990
    .
  96. ^ MOF-74 – A Potential Hydrogen-Storage Compound Archived 2012-06-20 at the Wayback Machine. Nist.gov
  97. ^ Researchers Demonstrate 7.5 wt% Hydrogen Storage in MOFs Archived 2007-02-28 at the Wayback Machine. Green Car Congress (2006-03-06)
  98. ^ New MOF Material With hydrogen Uptake Of Up To 10 wt% Archived 2010-05-07 at the Wayback Machine. 22 February 2009
  99. ^ Matt McGrath (18 April 2020). "Climate change: 'Bath sponge' breakthrough could boost cleaner cars". BBC News. Archived from the original on 19 April 2020. Retrieved 19 April 2020.
  100. S2CID 215789994. Archived
    from the original on 25 February 2022. Retrieved 19 April 2020.
  101. ^ R. K. Ahluwalia, T. Q. Hua, J. K. Peng and R. Kumar System Level Analysis of Hydrogen Storage Options Archived 2011-07-19 at the Wayback Machine. 2010 DOE Hydrogen Program Review, Washington, DC, June 8–11, 2010
  102. ^ Stephen Lasher Analyses of Hydrogen Storage Materials and On-Board Systems Archived 2011-09-29 at the Wayback Machine. DOE Annual Merit Review June 7–11, 2010
  103. ^ S&TR | Setting a World Driving Record with Hydrogen Archived 2008-12-03 at the Wayback Machine. Llnl.gov (2007-06-12)
  104. ^ Compact (L)H2 Storage with Extended Dormancy in Cryogenic Pressure Vessels Archived 2011-09-29 at the Wayback Machine. Lawrence Livermore National Laboratory June 8, 2010
  105. ^ Technical Sessions Archived 2011-07-11 at the Wayback Machine. FISITA 2010
  106. S2CID 219971360
    .
  107. S2CID 38107525
    .
  108. doi:10.1016/j.enconman.2006.11.017
    .
  109. doi:10.1016/j.ijhydene.2009.10.011
    .
  110. ^ Dan Eliezer et al. A New Technology for Hydrogen Storage in Capillary Arrays. C.En & BAM
  111. doi:10.1016/j.ijhydene.2013.03.107
    .
  112. ^
    doi:10.1016/j.matpr.2017.09.072
    . Retrieved 16 November 2020.
  113. doi:10.1016/j.ijhydene.2011.10.034
    . Retrieved 16 November 2020.
  114. doi:10.1016/j.jnoncrysol.2004.08.151
    . Retrieved 16 November 2020.
  115. S2CID 225544099
    . Retrieved 16 November 2020.
  116. ^ "R&D of large stationary hydrogen/CNG/HCNG storage vessels" (PDF). Archived (PDF) from the original on 2016-03-03. Retrieved 2012-07-14.
  117. ^ a b "COMMISSION STAFF WORKING DOCUMENT: Energy storage – the role of electricity" (PDF). European Commission. 1 Feb 2017. Archived (PDF) from the original on 8 November 2020. Retrieved 22 April 2018.
  118. S2CID 236299486. Archived
    from the original on 2022-10-16. Retrieved 2022-06-27.
  119. ^ 1994 – ECN abstract Archived 2004-01-02 at the Wayback Machine. Hyweb.de
  120. ^ "European Renewable Energy Network Study" (PDF). Brussels: European Union. January 2012. pp. 86, 188. Archived (PDF) from the original on 2019-07-17. Retrieved 2012-09-02.
  121. ^ "Why storing large scale intermittent renewable energies with hydrogen?". Hyunder. Archived from the original on 2013-11-11. Retrieved 2018-11-25.
  122. ^ "Storing renewable energy: Is hydrogen a viable solution?" (PDF). [permanent dead link]
  123. ^ "Bringing North Sea Energy Ashore Efficiently" (PDF). World Energy Council Netherlands. Archived (PDF) from the original on 23 April 2018. Retrieved 22 April 2018.
  124. ^ Gerdes, Justin (2018-04-10). "Enlisting Abandoned Oil and Gas Wells as 'Electron Reserves'". Greentech Media. Archived from the original on 2018-04-23. Retrieved 22 April 2018.
  125. ^ 1979 - Underground hydrogen storage. Final report.
  126. ^ hydrogen storage cavern system
  127. S2CID 236299486
    .
  128. ^ Energy storage 2012
  129. ^ 1994 - ECN abstract
  130. ^ "2006-Underground hydrogen storage in geological formations" (PDF). Archived from the original (PDF) on 2007-06-13. Retrieved 2024-02-27.
  131. ^ Brookhaven National Lab -Final report
  132. ^ Large-scale hydrogen underground storage for securing future energy supplies Archived 2014-07-28 at the Wayback Machine
  133. ^ LINDBLOM U.E.; A conceptual design for compressed hydrogen storage in mined caverns
  134. ^ Energy technology analysis: Prospects for Hydrogen and Fuel Cells (International Energy Agency 2005) p.70
  135. ^ ORNL-Pag.20 Archived 2008-12-06 at the Wayback Machine
  136. S2CID 115848429
    .
  137. ^
    S2CID 247822881
    .
  138. ^
    ISSN 1996-1073
    .
  139. S2CID 240290598
    .
  140. ^
    S2CID 225452215
    .
  141. S2CID 121951492
    .
  142. ^ a life-cycle cost analysis framework for geologic storage of hydrogen
  143. ^ Hyunder
  144. ^ Storing renewable energy: Is hydrogen a viable solution? [permanent dead link]
  145. ^ The role of hydrogen storage in a clean responsive power system
  146. ^ "Underground Sun Storage - Publikationen - Presse/Publikationen". Archived from the original on 2019-04-16. Retrieved 2019-04-16.
  147. ^ Hornyak, Tim (1 November 2020). "An $11 trillion global hydrogen energy boom is coming. Here's what could trigger it". CNBC. Archived from the original on 20 May 2021.
  148. doi:10.24425/ams.2020.133198
    .
  149. ^ Rathi, Akshat (11 December 2017). "Batteries can't solve the world's biggest energy-storage problem. One startup has a solution". qz.com. Quartz. Archived from the original on 23 April 2018. Retrieved 22 April 2018.
  150. ^ "Munich-based clean-tech startup Electrochaea and Hungarian utility MVM establish power-to-gas joint venture". MVM Group. 24 October 2016. Archived from the original on 23 April 2018. Retrieved 22 April 2018.
  151. ^ "SoCalGas and Opus 12 Successfully Demonstrate Technology That Simplifies Conversion of Carbon Dioxide into Storable Renewable Energy". prnewswire.com. prnewswire. Archived from the original on 23 April 2018. Retrieved 22 April 2018.
  152. ^ Ambrose, Jillian (2018-01-06). "Energy networks prepare to blend hydrogen into the gas grid for the first time". The Telegraph. Archived from the original on 2018-04-23. Retrieved 22 April 2018.
  153. ^ Anscombe, Nadya (4 June 2012). "Energy storage: Could hydrogen be the answer?". Solar Novus Today. Archived from the original on 19 August 2013. Retrieved 3 November 2012.
  154. ^ "naturalhy.net" (PDF). www.naturalhy.net. Archived from the original (PDF) on January 18, 2012.
  155. ^ Mike Millikin (2014-11-18). "Toyota FCV Mirai launches in LA; initial TFCS specs; $57,500 or $499 lease; leaning on Prius analogy". Green Car Congress. Archived from the original on 2014-11-21. Retrieved 2014-11-23.
  156. ^
    doi:10.1016/j.rser.2014.10.027
    .
  157. ^ Evans, Scarlett (August 20, 2018). "Researchers to create hydrogen energy source using nanotechnology". United Kingdom. Archived from the original on December 16, 2018. Retrieved December 14, 2018.
  158. ISBN 978-1-59102-591-7
    . The situation is much worse than this, however, because before the hydrogen can be transported anywhere, it needs to be either compressed or liquefied. To liquefy it, it must be refrigerated down to a temperature of −253 °C (20 degrees above absolute zero). At these temperatures, fundamental laws of thermodynamics make refrigerators extremely inefficient. As a result, about 40 percent of the energy in the hydrogen must be spent to liquefy it. This reduces the actual net energy content of our product fuel to 792 kcal. In addition, because it is a cryogenic liquid, still more energy could be expected to be lost as the hydrogen boils away as it is warmed by heat leaking in from the outside environment during transport and storage.
  159. ^ Savvides, Nick (2017-01-11). "Japan plans to use imported liquefied hydrogen to fuel Tokyo 2020 Olympics". Safety At Sea. IHS Markit Maritime Portal. Archived from the original on 2018-04-23. Retrieved 22 April 2018.
  160. ^ S.Sadaghiani, Mirhadi (2 March 2017). "Introducing and energy analysis of a novel cryogenic hydrogen liquefaction process configuration". International Journal of Hydrogen Energy. 42 (9).
  161. ^ 1994 – ECN abstract Archived 2004-01-02 at the Wayback Machine. Hyweb.de. Retrieved on 2012-01-08.
  162. ^ European Renewable Energy Network Archived 2019-07-17 at the Wayback Machine pp. 86, 188
  163. ^ "Energy storage – the role of electricity" (PDF). European Commission. Archived from the original (PDF) on 8 November 2020. Retrieved 22 April 2018.
  164. ^ "Hyunder". Archived from the original on 2013-11-11. Retrieved 2013-11-11.
  165. ^ "Storing renewable energy: Is hydrogen a viable solution?" (PDF).[permanent dead link]
  166. ^ "BRINGING NORTH SEA ENERGY ASHORE EFFICIENTLY" (PDF). worldenergy.org. World Energy Council Netherlands. Archived (PDF) from the original on 23 April 2018. Retrieved 22 April 2018.
  167. ^ GERDES, JUSTIN (2018-04-10). "Enlisting Abandoned Oil and Gas Wells as 'Electron Reserves'". greentechmedia.com. Wood MacKenzie. Archived from the original on 2018-04-23. Retrieved 22 April 2018.
  168. ^ Chanchetti, Lucas Faccioni (2014-09-18). "Cientometria aplicada a materiais para armazenamento de hidrogênio". Archived from the original on 2021-05-01. Retrieved 2021-11-19.
  169. ^
    S2CID 199075995
    .
  170. S2CID 104929670
    , retrieved 2021-11-19
  171. ISSN 1754-5692. Archived
    from the original on 2022-10-16. Retrieved 2021-11-19.

External links
Wikimedia Commons has media related to Hydrogen storage.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Hydrogen_storage&oldid=1220607881"